Subscribe to Our Youtube Channel
Related Manuals for Atlas Copco XAMS396E
Summary of Contents for Atlas Copco XAMS396E
- Page 1 XAMS396E XAS486E XAVS366E XAHS376E XAMS466E XAVS306E PORTABLE COMPRESSOR INSTRUCTION BOOK Atlas Copco – Portable Air Division 1092038501...
-
Page 2: Table Of Contents
INSTRUCTION BOOK Please read the following instructions carefully before starting to use your machine. Follow the instructions in this booklet and we guarantee you years of trouble free operation. Always keep the manual available near the machine. In all correspondence always mention the compressor type and serial number, shown on the data plate. -
Page 3: Safety Precautions For Portable Compressors
Only people that have the right skills should be allowed — a scertain that the towing eye can swivel freely on to operate on Atlas Copco equipment and to observe all the hook, relevant local safety requirements and ordinances. —... - Page 4 5. Never move a unit when external lines or hoses are connected to the outlet valves, to avoid damage to 2. Parts shall only be replaced by genuine Atlas Copco valves, manifold and hoses. replacement parts. 6. Do not use compressed air from any type of 3.
- Page 5 All responsibility for any damage or injury resulting damage to parts. from neglecting these precautions non-observance of ordinary caution and due care required in handling, operating, maintenance or Specific safety precautions repair, also if not expressly mentioned in this instruction manual, is disclaimed by Atlas Copco.
-
Page 6: Main Parts
The air receiver is provided with effective working pressure of 12 bar, XAMS466E/ a safety valve. XAMS396E built for a nominal effective working — — — — F rame and axle pressure of 8.6 bar, XAS486E built for a nominal... -
Page 7: Main Parts
INSTRUCTION BOOK XAS Compressor Main Parts Main parts Main Motor Left Bracket Air Filter Oil Indicator Minimum Pressure Valve S1 Pressure Switch Filler Plug Air Receiver Safety Valve Oil Filter S2 Pressure Switch Solenoid Valve Regulating Valve Pressure Gauge 1 Fan Motor Compressor Element Oil Stop Valve... -
Page 8: Compressor System
INSTRUCTION BOOK Compressor Regulating System O I L 油 油 1. Main Motor 13. Scavenge Line 25. Refill plug 2. Unloader Assembly 14. Flow Restrictor 26. Thermostatic Bypass Valve 3. Pressure Diversity Sensor 15. Temperature Sensor 27. Oil Indicator 4. Air Filter 16. -
Page 9: Oil System
INSTRUCTION BOOK removed by the separator element. The oil collects in For this reason, the oil filter must be replaced at the receiver and on the bottom of the separator regular intervals (See Preventive maintenance element. schedule for the compressor). The air leaves the receiver via a minimum pressure valve (22) that prevents the receiver pressure from Continuous Regulating System... -
Page 10: Electrical System
INSTRUCTION BOOK corresponding unloading pressure. Unloading pressure and open, the air receiver pressure in air receiver will = normal working pressure + 1.4 bar be down to 2.5 bar to save power. When consumption resumed and outlet valve (23) pressure is down to 5 When the air consumption is resumed, the blow off bar, the pressure switch closed, the solenoid valve valve closes and the throttle valve gradually opens the... -
Page 11: Operating Instructions
INSTRUCTION BOOK Operating Instructions Packing, towing, lifting Safety Precautions The operator is expected to apply all relevant safety precautions, including those mentioned on the page 2-4. Towing instructions Attention: Before towing the compressor, ensure the — B efore putting compressors into use, check the towing equipment of the vehicle matches the brake system as described in ‘brake adjustment’. - Page 12 INSTRUCTION BOOK of oil level gauge should register in the green range. Before start: Add oil if necessary. 1. After parking, check the compressor and confirm all Before removing oil filler plug ensure that the parts are in correct place especially the connection to avoid leakage and hazard.
-
Page 13: During Operation
INSTRUCTION BOOK 4. When compress air temperature higher than Display, Button and Appearance ambient temperature about +32 ℃ , rotate load/unload 2. Fan motor overload indicator lamp — L amp lighting switch to ‘load’ position then compressor turn to load when fun motor overload. -
Page 14: Maintenance
(1) More frequently when work in dusty environment (2) Use special filter element with bypass valve made by Atlas Copco. (see spare part list) Keep the bolts of the housing, the lifting eye, the towbar and the axle securely tightened. Refer to section 8 ‘... -
Page 15: Preventive Maintenance Schedule For Compressor
INSTRUCTION BOOK tighten the filler plug. OIL AND OIL FILTER CHANGE Never add more oil. Overfilling results in oil consumption. CLEANING COOLERS The prescribed interval (see section 4.2) is based on an oil temperature of up to 100 °C and normal operating conditions. -
Page 16: Storage
All compressor parts Service Pcks Contact Atlas Copco, we guarantee that all necessary A Service Pak is a collection of parts to be used for a parts and tools supply in time. specific maintenance measure. (e.g 50, 500, 1000h... -
Page 17: Adjustments And Servicing Procedures
INSTRUCTION BOOK Adjustment and Servicing Procedures O I L O I L A I R A I R 油 路 气 路 油 气 路 Adjustment of the continuous regulating system The working pressure is determined by the tension of valve (7) until a pressure high than normal working the spring in the regulating valve (7). -
Page 18: Air Filter
Do not use inject air to airing it. 3. Safety cartridge 6. Vacuum valve 5. Check element whether broken, change it if necessary. The Atlas Copco air filters are specially 6. Assemble filter. designed application. Air receiver non-genuine air filters may lead to severe damage The air receiver is tested according to official standard. -
Page 19: Safety Valve
INSTRUCTION BOOK Safety Valve Brake adjustment All adjustments or repairs are to be done by an authorized representative of the valve repair Following checks must be carried out: — A check of the opening of the lifting gear, twice a year. -
Page 20: Problem Solving
Air filter clogged c. Disassembly and check normal c. Regulating valve fault d. Consult Atlas copco d. Oil separator clogged e. Knock down air filter and hose, check unloader e. Unloader assembly not completely valve, replace part if necessary. Attention: There... -
Page 21: Technical Specification
1 L=0.220 UK gal /min 1 L=0.035 cu.ft XAVS306E 18.4 1 m=3.281 ft XAHS376E 22.7 1 mm=0.039ft XAMS466E 28.2 /min=35.35 cfm XAMS396E 23.4 1 mbar=0.401 in wc XAS486E 28.5 1 N=0.225 lbf F=32+(1.8×t ℃ ) c. Limitations ℃ = ( F-32)/1.8 —...
Need help?
Do you have a question about the XAMS396E and is the answer not in the manual?
Questions and answers