Advertisement
Quick Links
Advertisement
Related Manuals for Genius SIROCCO 250
Summary of Contents for Genius SIROCCO 250
- Page 1 SIROCCO SIROCCO...
- Page 2 “16”. 6) GENIUS declines all liability caused by improper use or use other than that for which the 18) GENIUS décline toute responsabilité quant à la sécurité et au bon fonctionnement de automated system was intended.
- Page 3 Available accessories pag.20 CE DECLARATION OF CONFORMITY FOR MACHINES (DIRECTIVE 98/37/CE) Manufacturer: GENIUS S.p.a. Address: Via Padre Elzi, 32 - 24050 - Grassobbio BERGAMO - ITALY SIROCCO mod. operator Declares that: • is built to be integrated into a machine or to be assembled with other machinery to create a machine under the provisions of Directive 98/37/CE;...
- Page 4 ATTENTION: • The correct operation and the declared specifications only apply if GENIUS accessories and safety devices are used. • As no mechanical clutch device is fitted, a control unit with adjustable electronic clutch is required to ensure the necessary anti- crushing safety.
- Page 5 3. TECHNICAL SPECIFICATIONS ° ( µ ( ° 0 ° 0 ° ( If no closing and opening mechanical travel stops are used, the operator travel is 350 mm With leaves exceeding 1.8 m the fitting of an electric lock is required to ensure the leaf locking 3.1.
- Page 6 4.3. Installation dimensions Determine the fitting position of the operator with reference to Fig.4. During this phase it is important to define if the mechanical travel stops are to be used: by eliminating the mechanical travel stops the operator travel increases thus changing the installation dimensions A and B.
- Page 7 2) Assemble the rear fitting to the operator as shown in Fig.8. Fig. 8 3) Check if the front fitting is in the correct position as shown in Fig.9 (with closing mechanical travel stop) or in Fig.10 (without closing mechanical travel stop). If this is not the case, temporarily supply power to the operator to position the fitting. ATTENTION: The operator can be moved by hand only if it is installed on the gate and in released position (see paragraph 6).
- Page 8 6) Close the leaf and, keeping the operator in a perfect horizontal position, determine the fastening point of the front bracket (Fig.13). 7) Temporarily fix the front bracket with two welding spots (Fig.13). Note: if the gate structure does not allow a fix bracket fastening it is necessary to create a sturdy supporting base in the gate structure.
- Page 9 4.6. Mechanical travel stops The SIROCCO operators are equipped with opening and closing mechanical travel stops. They can be used instead of the leaf mechanical limit stops. To adjust the mechanical travel stops operate as follows: 4.6.1. Adjusting the opening mechanical travel stop 1) Set the operator for manual operation, see paragraph 6 2) Manually move the leaf in opening position.
- Page 10 4.7. Limit switches The “LS” models are equipped with opening and closing limit switches. Therefore they require the use of a control board able to control these inputs. Note: The limit switches are triggered for the first and the last 30 mm of the travel. Therefore the operator should use the whole available travel during the opening phase.
- Page 11 5) Position again the cover by sliding it on the lower casting and make sure that it reaches the stop, Fig.25. 6) Screw both lower screws, Fig.25. Fig. 25 4.8. Start-up ATTENTION: Cut power before any job on the system or on the operator. Carefully observe points 10, 11, 12, 13 and 14 of the SAFETY GENERAL RULES.
- Page 12 6. MANUAL OPERATION If the automated system needs to be moved manually due to a power lack or to an operator malfunction, proceed as follows: 1) Cut power by means of the safety circuit breaker (even in the event of a power lack). 2) Slide the protective cap, Fig.26/1.
- Page 13 24) Sólo puede transitarse entre las hojas si la cancela está completamente abierta. 9) GENIUS is niet aansprakelijk als de regels der goede techniek niet in acht genomen zijn 25) El usuario no debe por ningún motivo intentar reparar o modificar el producto, debe bij de bouw van het sluitwerk dat gemotoriseerd moet worden, noch voor vervormingen siempre dirigirse a personal cualificado.
- Page 14 Les descriptions et les illustrations du présent manuel sont fournies à titre indicatif. GENIUS se réserve le droit d’apporter à tout moment les modifications qu’elle jugera utiles sur ce produit tout en conservant les caractéristiques essentielles, sans devoir pour autant mettre à...
Need help?
Do you have a question about the SIROCCO 250 and is the answer not in the manual?
Questions and answers