Selecting Channels; Selecting Fader Modes - Yamaha 01V96i Owner's Manual

22
Operating Basics

Selecting Channels

To select a channel on the 01V96i,
press the corresponding [SEL]
button. To adjust the Pan and EQ
settings, use the rotary controls in
the SELECTED CHANNEL sec-
tion. To select a channel on pages
that cover multiple channels, press
the corresponding [SEL] button.
1.
Press the corresponding
LAYER button to select a
layer that includes the
desired channel (see
page 21).
To select ST IN channels, press
the [ST IN] button.
2.
Use the corresponding [SEL] button to
select the desired channel.
The channel is selected and the [SEL] button indi-
cator lights up.
The Channel's ID and short name appear in the
upper-left corner of the display. If the currently-dis-
played page contains a relevant channel parameter,
the cursor moves to that parameter automatically. If
the currently-displayed page contains no such
parameter, a page that does contain such a parame-
ter is selected automatically.
Tip: For paired Input or Output Channels, the channel
for which you pressed the [SEL] button is selected, and
its indicator lights up. The [SEL] button indicator of
the paired partner flashes.
3.
To select the Stereo Out, press the STE-
REO [SEL] button.
Repeatedly pressing the STEREO [SEL] button tog-
gles between the Stereo Out left and Stereo Out
right channels.
If the currently-displayed page contains a relevant
Stereo Out parameter, the cursor moves to that
parameter automatically. If the currently-displayed
page contains no such parameter, a page that does
contain such a parameter is selected automatically.
01V96i—Owner's Manual

Selecting Fader Modes

The function of channel faders (1–16) depends on the
selected Layer and Fader mode.
1.
2.
HIGH
Q
HIGH-MID
FREQUENCY
LOW-MID
LOW
GAIN
• When the [HOME] button indicator lights up:
• When one of the [AUX1]–[AUX8] button indica-
The following table shows the channel fader functions
for each Layer and Fader mode.
[1–16]
button
[17–32]
button
[REMOTE]
button
[MASTER]
button
Note: You cannot select the [AUX1]–[AUX8] buttons
while the Master layer is selected. If you switch to the Mas-
ter layer while one of the [AUX1]–[AUX8] button indica-
tors is lit, the indicator automatically turns off and the
[HOME] button indicator lights up.
Select a layer that includes the desired
channel (see page 21).
Press the FADER MODE buttons to select
a Fader mode.
FADER MODE
1 2 3
AUX AUX AUX AUX
5 6 7
AUX AUX AUX AUX
HOME (METER)
The button indicators identify the following Fader
modes:
You can use channel faders to control Input Chan-
nels and ST IN Channel levels or Output Channels
(Aux Out 1–8, Bus Out 1–8) master levels.
tors light up:
You can use channel faders to control the corre-
sponding Aux Send level.
LAYER
Fader Mode
buttons
[HOME] button
[AUX1]–[AUX8]
buttons
[HOME] button
[AUX1]–[AUX8]
buttons
[HOME] button
[AUX1]–[AUX8]
buttons
[HOME] button
[AUX1]–[AUX8]
buttons
4
8
Channel Strip Fader
1–8 9–16
Input Channel 1–16 level
Input Channel 1–16 Aux
Send level
Input Channel 17–32 level
Input Channel 17–32 Aux
Send level
Operation depends on the
selected target.
Aux Send Bus Out
master 1–8 master1–8
output level output level
No operation