Warranty and Service Information Enjoy your Alto-Shaam Hot Well! Halo Heat® Technology Better food quality. Individual well control. Inside Alto-Shaam drop-in food wells, gentle Halo Heat® surrounds each well with precisely controlled, even heat. Water-less design offers safety and less maintenance.
Delivery This Alto-Shaam appliance has been thoroughly tested The serial number is required for all inquiries. and inspected to ensure only the highest quality Always include both model and serial number(s) in any appliance is provided. Upon receipt, check for any correspondence regarding the appliance.
Alto-Shaam of all liability. • Remove all protective plastic fi lm, packaging materials, and accessories from the appliance before connecting electrical power.
Safety Procedures • The appliance is intended to hold hot food for the The following signal words and symbols may be used purpose of human consumption. No other use for this throughout this manual. appliance is authorized and is therefore considered dangerous.
Page 8
If your appliance makes an especially loud noise warranty and relieve Alto-Shaam of all liability. when starting up, shut down the appliance and call a Children should be supervised to ensure qualifi ed and trained service technician.
Personnel qualifié : Sectionnez l’alimentation avant toute intervention. LA-38950 Every Alto-Shaam product is precision calibrated prior to release from the factory to ensure accurate temperature control. Mount unit to allow a minimum of 1" (25mm) clearance between unit bottom surface and combustible materials.
Site Installation The Alto-Shaam hot well must be installed in a location that Clearance Requirements will permit it to function for its intended purpose and to allow adequate clearance for ventilation, proper cleaning, and 1"...
Page 12
Installation Net Weights Model D443 D643 100-HW 25 lb (11 kg) 29 lb (13 kg) 31 lb (14 kg) 35 lb (16 kg) 100-HWLF 27 lb (12 kg) 31 lb (14 kg) — — 100-HWRS — 29 lb (13 kg) —...
Page 13
Installation Control Installation Instructions Apply a food grade silicone under the edge of the hot well support flange. “TOP” ETCHING DECOR FACE SCREWS Cut an appropriate sized opening in the location where Making sure "TOP" etching is at the top, route control the control is to be positioned.
Page 14
Installation 100-HWRS/D6 Control Housing Installation Instructions (5022756) 1. Drill four (4) 3/8" (9.5mm) holes in mounting surface. 2. Align housing with holes and attach housing to mounting surface with 5/16" (M9) bolt, flat washer, lock washer and locknut (not supplied). MN-48161 •...
Page 15
Installation 100-HWRS/D6 Switch Housing Installation New Installation: 1. Cut switch cut-out in cabinet to 0.865" x 1.200" ± 0.020". 2. Install switch body in cutout. 3. Crimp two (2) Molex spade connectors (190020024 or equivalent) and one (1) #10 ring terminal to 16/3 SJT, 120V wire and run to 120V power source.
Page 16
Installation Locking Kit 5020849 Installation (Option) Put clip in highest pair of slots that Tighten screw so that it presses against the fit under the counter counter, holding the well in place. Do not overtighten the screws. One clip for each corner MN-48161 •...
Page 17
SRV-20035 REV. 1 Alto-Shaam Technical Service 800-558-8744 x6702 servicedept@alto-shaam.com 1 of 7 STUD LOCATION CIRCLE q CLEAN THE BOTTOM SURFACE OF THE COUNTER THAT THE HOT WELL WILL MOUNT q USE A PAPER GAUGE (KIT INCLUDES PAPER TEMPLATES - USE SCISSORS TO CUT TO (INSIDE CUTOUT SURFACE OF COUNTER MUST BE FINISHED/SEALED FOR THE IMAGES OUT AND FOLD ON DASHED LINES).
Page 18
ADDED UNDERMOUNT HARNESS 3/17/2016 SRV-20035 REV. 1 Alto-Shaam Technical Service 800-558-8744 x6702 servicedept@alto-shaam.com 1 of 7 Installation Undermount Kit 5020793 Installation - continued (option) STUD LOCATION CIRCLE q CLEAN THE BOTTOM SURFACE OF THE COUNTER THAT THE HOT WELL WILL MOUNT q ...
Page 19
REPEAT STEPS 14 & 15 FOR THE WIRE ON THE OPPOSITE SIDE. WHEN MAKING BEFORE. THE BEND, LEAVE ABOUT 6” (152mm) BETWEEN THE BENDS. SRV-20035 REV. 1 Alto-Shaam Technical Service 800-558-8744 x6702 servicedept@alto-shaam.com 5 of 7 HOOKS q LOOP ONE “V” AROUND THE T-NUT SO THAT THE LOOP GOES BELOW THE BOLT.
Page 20
Installation Undermount Kit 5020793 Installation - continued (option) SRV-20035 REV. 1 Alto-Shaam Technical Service 800-558-8744 x6702 servicedept@alto-shaam.com 7 of 7 MN-48161 • Rev 01 • 08/23 • Hot Food Holding Drop-In Well...
Electrical Connections • A rating tag is permanently mounted on the WARNING appliance. Make sure the source voltage matches the voltage listed on the rating tag. To prevent SERIOUS INJURY, DEATH or PROPERTY DAMAGE: • This appliance is equipped with a three-prong grounding plug.
Operation 5. Reset thermostat(s) as needed CAUTION After all products are loaded into the appliance, it may be necessary to reset the thermostat(s). Since proper To prevent personal injury or temperature range depends on the type of products property damage: and the quantities being held, periodically check each item to make certain the correct temperatures are being Always use hand protection when...
Failure to clean the appliance properly may cause fire, personal injury, death, invalidates the warranty and relieves Alto-Shaam of all liability. MN-48161 • Rev 01 • 08/23 • Hot Food Holding Drop-In Well...
Page 24
Cleaning and Preventative Maintenance WARNING WARNING To prevent serious personal injury, death, or To prevent serious injury, death, or property damage, always disconnect the appliance property damage: from the power source before cleaning Do not steam clean, hose down or flood the or servicing.
No person except an officer of Alto-Shaam, Inc. is authorized to modify this warranty or to incur on behalf of Alto-Shaam any other obligation or liability in connection with Alto- Shaam equipment.
Page 28
Miami, FL US A INDIA MEXICO Pune, India Leon, Mexic o AUSTRALIA Brisbane, Queenslan d Menomonee Falls, WI U.S.A. Phone 800 -558-8 744 | +1-262-251-3800 | alto-shaam.co m ASIA FRANCE MEXICO Shanghai, China Aix en Provence, France Phone +52 1 477-717-3108 Phone +86-21-6173-0336 Phone +33(0)4-88-78-21-73 MIDDLE EAST &...
Need help?
Do you have a question about the 100-HW/D4 and is the answer not in the manual?
Questions and answers