IMPORTANT SAFETY INTRODUCTIONS W A R N I N G Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire, and /or serious personal injury. W A R N I N G When using this product, basic precaution should always be followed, including the following.
SPECIFIC SAFETY RULES ■ Know your product. Read the operator’s manual carefully. Learn the machine’s applications and limitations as well as the specific potential hazards related to this product. ■ To reduce the risk of injury, keep children and visitors away. All visitors should wear safety glasses and be kept a safe distance from the work area.
Page 7
SPECIFIC SAFETY RULES ■ Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. A wire gauge size (A.W.G.) of at least 14 is recommended for an extension cord 25 feet or less in length. If in doubt, use the next heavier gauge.
SYMBOLS Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer. SYMBOL NAME DESIGNATION/EXPLANATION Volts Voltage Amperes Current Hertz Frequency (cycles per second)
Page 9
If you do not understand the warnings and instructions in the operator’s manual, do not use this product. Call GREENWORKS customer service for assistance. The operation of any power tool can result in foreign objects being thrown into your eyes, which can result in severe eye damage.
ELECTRICAL W A R N I N G The double insulated system is intended to protect the user from shock resulting from a break in the product’s internal insulation. Observe all normal safety precautions to avoid electrical shock. DOUBLE INSULATED Double insulation is a concept in safety in electric power tools, which eliminates the need for the usual three-wire grounded power cord.
KNOW YOUR PRESSURE WASHER The safe use of this product requires an understanding of the information on the tool and in this operator’s manual, as well as a knowledge of the project you are attempting. Before using this product, familiarize yourself with all operating features and safety rules. (See Figure 2.) Handle High Pressure Hose...
PACKING LIST PART NAME ERP NO. FIGURE • Pressure Washer (including the spray tips) 25°Spray Tip 40°Spray Tip C1101896-00 • Trigger Handle • Wand Assembly 31115661 • 20 ft. High Pressure Hose 31160363 • Detergent Tank 31111368 • Spray Tip Cleaning Tool 33201671 •...
ASSEMBLY UNPACKING This product requires assembly. ■ Carefully remove the product and any accessories from the box. Make sure that all the contents from the packaging list are included. W A R N I N G Do not use this product if any parts on the Packing List are already assembled to your product when you unpack it.
Page 14
ASSEMBLY ASSEMBLING THE GUN HOLDER (See Figure 3.) ■ Insert the gun holder into the slot until it locks into its tabs. Fig. 3 ASSEMBLING THE PRESSURE WASHER GUN ■ Insert the male end (A) of the wand into the female bayonet outlet (B) firmly. (See Figure 4-1.) ■...
Page 15
ASSEMBLY CONNECTING HIGH PRESSURE HOSE TO THE TRIGGER HANDLE (See Figure 5.) ■ Connect the high pressure hose to the pressure washer gun assembly by turning the fitting clockwise. Ensure the fitting is fully tightened to the pressure washer gun. NOTE: For easier installation of the hose to the unit or trigger it is suggested to add pressure washer or dish detergent to the rubber seal at each end of the hose.
Page 16
ASSEMBLY CONNECTING THE GARDEN HOSE (See Figure 7.) C A U T I O N : Always observe all local regulations when connecting hoses to the water main. Some areas have restrictions against connecting directly to public drinking water supply to prevent the feedback of preventer is usually permitted.
OPERATION W A R N I N G Do not allow familiarity with the product to make you careless. Remember that a careless fraction of a W A R N I N G Never direct a water stream toward people or pets, or any electrical device. Failure to heed this warning could result in serious injury.
Page 18
OPERATION STARTING ANd STOPPING THE PRESSURE WASHER CAUTION : Do not run the pump without the water supply connected and turned on. ■ Connect the garden hose. ■ Turn the garden hose on then squeeze the high pressure trigger to relieve air pressure. Once a steady stream of water appears, release the trigger.
Page 19
OPERATION USING THE SPRAY WAND TRIGGER For greater control and safety, keep both hands on the pressure washer gun at all times. ■ Pull back and hold the trigger to operate the pressure washer. TO ENGAGE THE LOCK-OUT (See Figure 9-1.) ■...
Page 20
OPERATION CHANGING THE SPRAY TIP (See Figure 10.) W A R N I N G NEVER change spray tips without engaging the lock-out on the trigger handle and NEVER point the wand at your face or at others. The quick-connect feature contains small springs that could eject the spray tip with some force.
Page 21
OPERATION OPERATING THE PRESSURE WASHER (See Figure 11.) Use only detergents designed for pressure washers. Soap is applied under low pressure high volume for optimum performance. Soap can not be applied under high pressure with this machine. To clean: ■ Install the soap attachment on the trigger handle. ■...
MAINTENANCE W A R N I N G When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage. W A R N I N G Before inspecting, cleaning or servicing the machine,turn off the unit, unplug from the outlet, pull trigger to release water pressure and disconnect the high pressure hose.
Page 23
MAINTENANCE SPRAY TIP MAINTENANCE (See Figure 12.) Excessive pump pressure (a pulsing sensation felt while squeezing the trigger) may be the result of a clogged or dirty spray tip. Fig. 12 ■ Unplug the pressure washer. ■ Turn off the pressure washer and shut off the water supply. Pull trigger to release water pressure. ■...
Page 24
MAINTENANCE QUICK WINTERIZING PROCEdURE If you cannot do the Optimum Winterizing procedure, you can still protect your pressure washer from winter damage by doing below: ■ Disconnect all water connections. ■ Turn on the machine for a few second, until the remaining water in the pump exits. Turn off immediately. ■...
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION On/Off switch is Turn switch to the “ON” ( | ) position. Squeeze gun in the “OFF” (O) trigger. position. Power cord is not Plug in power cord. plugged in. Extension cord is too long. Replace extension cord with either a 25’...
Page 26
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Filter on detergent Run warm water through the filter to remove build suction tube is clogged. Unit does not reach Damaged or clogged Remove obstruction or replace detergent suction high pressure. detergent suction tube. (continued) tube.
Page 27
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Supply voltage below Verify that only the pressure washer is running on minimum. this circuit. System has residual Turn unit “OFF”, squeeze trigger on spray wand to pressure. release pressure, then turn unit “ON”. Voltage loss due to Unplug any extension cords attached and plug the Motor buzzes but fails unit directly into the outlet.
Greenworks hereby warranties this product, to the original purchaser with proof of purchase, for a period of three (3) years against defects in materials, parts or workmanship. Greenworks, at its own discretion will repair or replace any and all parts found to be defective, through normal use, free of charge to the customer.
EXPLODED VIEW This equipment is designed to be used with authorized parts ONLY. If equipment is used with third party parts that DO NOT comply with below minimum specifications, user assumes all risks and liabilities and all applicable express and, except where prohibited, implied warranties are void. EN - 27...
Need help?
Do you have a question about the 5124202 and is the answer not in the manual?
Questions and answers