Equipment Mains Working Setting - Marantz PM-17SA User Manual

FOREWORD
This section must be read before any connection is made to
the mains supply.
WARNINGS
Do not expose the equipment to rain or moisture.
Do not remove the cover from the equipment.
Do not push anything inside the equipment through the
ventilation holes.
Do not handle the mains lead with wet hands.

EQUIPMENT MAINS WORKING SETTING

Your Marantz product has been prepared to comply with the
household power and safety requirements that exist in your
area.
This product can be powered by 120 V AC only.
COPYRIGHT
Recording and playback of any material may require consent.
For further information refer to the following:
— Copyright Act 1956
— Dramatic and Musical Performers Act 1958
— Performers Protection Acts 1963 and 1972
— any subsequent statutory enactments and orders
ABOUT THIS USER GUIDE
Refer to the Figures on the page 20 at the rear of this user
guide. The numbers on the diagrams correspond to those in
the text. All references to the connections and controls that
are printed in BOLD type are as they appear on the unit.
PRECAUTIONS
The following precautions should be taken when operating the
equipment.
GENERAL PRECAUTIONS
When setting the equipment ensure that:
- the ventilation holes are not covered
- air is allowed to circulate freely around the equipment
- it is on a vibration free-surface
- it will not be exposed to interference from an external source
- it will not be exposed to excessive heat, cold, moisture or
dust
- it will not be exposed to direct sunlight
- it will not be exposed to electrostatic discharges
Never place heavy objects on the equipment.
If a foreign body or water does enter the equipment, contact
your nearest dealer or service centre.
Do not pull out the plug by pulling on the mains lead, hold the
plug.
It is advisable when leaving the house, or during a thunder-
storm, to disconnect the equipment from the mains supply.
To ventilae the unit, do not install the unit in a rack or bookshelf, and
note the followings.
- Do not touch the top of the enclosure during operation.
- Do not block the openings in the enclosure during operation.
- Do not insert objects beneath the unit.
- Do not block the ventilation slots at the top of the unit.
Do not place anything about 1 meter above the top panel.
- Make a space of about 0.2 meter around the unit.
WARRANTY
Contact your local Marantz distributors for warranty information.
RETAIN YOUR RECEIPT AS PROOF OF PURCHASE
Your receipt is proof of a valuable purchase. Keep it in a safe place
where you can easily find it for filing insurance claims when necessary
or when corresponding with Marantz.
IMPORTANT
It is the responsibility of the consumer to establish proof of purchase
when seeking servicing covered by the warranty. Your receipt or in-
voice is valid as such proof.
U.K. ONLY
This undertaking is in addition to a consumer's statutory rights and
does not affect those rights in any way.
CONNECTIONS
(Page 2)
CONNECTIONS OF TUNER
Connect the output jacks of your stereo tuner to the LINE 1-
LINE 3 jacks of this unit.
CONNECTION OF VCR OR DVD PLAYER
Connection the audio output jacks of your VCR or DVD player
to the LINE1–LINE3 jacks of this unit.
CONNECTION OF COMPACT DISC PLAYER
Connect the output jacks of your CD player to the CD jacks of
this unit.
CONNECTION OF ANALOG TURNTABLE
Connect the L (Left) output cord of the turntable to the "L"
PHONO jack of this unit, and connect the R (Right) output cord
to the "R" PHONO jack. Also be sure to connect the turntable's
grounding wire to the GND jack of this unit. The GND jack
does not have to be connected if the turntable is not provided
with a grounding wire.
CONNECTION OF CD RECORDER/TAPE DECK
Connect the IN (line input) jacks of the CD recorder or the tape
deck to the OUT jacks of this unit, and connect the OUT (line
output) jacks of the CD recorder or the tape deck to the IN
jacks of this unit.
CONNECTION OF SPEAKER SYSTEMS
This unit is equipped with a sets of SPEAKERS terminals.
- The speakers in the speaker system should have an impedance
between 4 and 16 ohms. If speakers with an impedance of
less than 4 ohms are connected, the protection circuit may be
activated during play.
- Connect the Right channel speaker to the R terminals, and the
Left channel speaker to the L terminals.
- The output terminals have positive ( : Red) and negative
( : white) polarity, and each speakers also has the same
polarity ( and ). When connecting the speaker, be sure to
connect the terminals with the same polarity ( with
with ).
When connecting two pairs of speaker systems simulta-
neously, the impedance of each speaker system should be
no less than 8 ohm .
Connecting a speaker system with a lower impedance than
8 ohm may activate the protection circuitry and make normal
stereo reproduction impossible.
Connection of speaker cord
Strip coating from extermity.
Twist conductors.
Speaker cord
Turn counter-
clockwise to
loosen.
When combined with a Marantz SM-17SA (main amp), the PM-
17SA main amp can be used as a BTL amp (monaural). It can-
not be used as a BTL amp when combined with other prod-
ucts.
1
CAUTION:
Turn clockwise
Insert conduc-
tors. to tighten.
,