Subscribe to Our Youtube Channel
Related Manuals for Pentair V3000-SEA
Summary of Contents for Pentair V3000-SEA
- Page 1 ENERGON REVERSE OSMOSIS WATER PURIFICATION SYSTEM USER’S MANUAL MODEL: V3000-SEA, V15-SEA...
-
Page 2: Table Of Contents
CONTENTS _____________________________________________________________________________________________________________ 1. PRECAUTIONS AND GENERAL NOTES ..................3 2. PARTS INCLUDED ........................4 3. PRODUCT INFORMATION ......................5 3.1 Product Structure ........................5 3.2 Product Features ........................5 3.3 Specifications ........................6 3.4 Schematic Diagrams ......................6 3.5 Introduction to Main Parts ...................... 7 4. -
Page 3: Precautions And General Notes
1. PRECAUTIONS AND GENERAL NOTES _____________________________________________________________________________________________________________ CAUTION Please read this instruction manual carefully before installing and using this product. If you encounter any problems that are not addressed in this manual, please contact your local Pentair’ s distributor. WARNING: • To prevent damage to the system or property, • Before installation, please ensure that the electric shock or personal injuries, carefully equipment is turned off and that the cold water read and follow this manual. supply valve is closed. • Do not use with water that is microbiologically • During Installation, consider the convenience unsafe or of unknown quality without adequate of use and the room for movement during disinfection before or after the system. maintenance. • This reverse osmosis system will not protect • Do not touch the power plug with wet hands, against disease causing bacteria or remove and disconnect the power supply during naturally-occurring harmless bacteria. installation. • The water purification system must be installed • Before using the water purification system, to the cold water supply line. -
Page 4: Parts Included
Pentair authorized distributor. • Maintenance and replacement has to be • Residential water purification systems are only performed using parts or accessories approved suitable for personal and home use, and are not by Pentair recommended for commercial use. • Use of unauthorized parts or accessories may • The display value of TDS is calibrated with result in reduced product performance or standard NaCl solution and may differ from property damage. These are not covered by other TDS measuring instruments. Pentair’ s limited warranty. • If you have any questions after installation, • Do not disassemble or modify the water please contact your local Pentair authorized purification system. distributor. 2. PARTS INCLUDED _____________________________________________________________________________________________________________ Carefully unpack unit and make sure all components are present. See checklist below for the components included with your system. Packing List Reverse Osmosis Water Purification System 1 unit 1/4” PE tube Operation manual 1 booklet 3/8” PE tube... -
Page 5: Product Information
Check High pressure TDS Plug Water inlet Drain panel panel panel board cover valve switch solenoid valve solenoid valve 3.2. Product Features • Provides two grades of water quality: (1) Filtered (Clean) Water and (2) RO (Pure) Water for different water usage (Model V3000-SEA only). • RO (Pure) water can used for drinking and cooking. • Filtered (Clean) water can be used for food preparation and washing (Model V3000-SEA only). • Integrated quick change filter cartridge for easy filter replacement. • Slim machine design allows flexible installation. Filter Cartridges Functions Stage 1 : PP removes sediments, sand and rust; Carbon removes chlorine, colour, taste and odour. Stage 2: Removes TDS, some organics such as chloroform and carbon tetrachloride, as well as some heavy metals like arsenic, lead and cadmium. Stage 3: Improves taste. -
Page 6: Specifications
3.3. Specifications Model V3000-SEA V15-SEA RO Membrane Performance 400GPD Clean (Filtered) Water: 1.5 L/min System Flowrate Pure (RO) Water: 1.0 L/min Pure (RO) Water: 1.0 L/min Dual Faucet: Pure (RO) Water Outlet(s) Single Faucet: Pure (RO) Water and Clean (Filtered) Water Appearance Cabinet Type Product Dimensions 460 x 132 x 361mm Inlet Water Quality Chlorinated City Water Inlet Water Pressure 15 - 55 PSI Operating Pressure 60 - 115 PSI Operating Environment Ambient temperature 4°C-40°C, relative humidity ≤90% (indoors) Power Supply 110-220V, 50/60Hz Power - TDS Value; - System status indicators: Water production (Processing); Flushing; Leak; Error Display - Individual cartridge lifespan progress bars + Cartridge replacement reminder Function Buttons: Select Button; Flush Button; Reset Button... -
Page 7: Introduction To Main Parts
1 piece 12 months Φ53mm Filter housing Polypropylene 2 pieces 5 years Φ74mm RO housing Polypropylene 1 unit 5 years Φ107mm Dual faucet Stainless steel 1 piece 5 years (Model V3000-SEA) Single faucet Copper 1 piece 5 years (Model V15-SEA) PE plastic tubes Polyethylene 5 years Integrated waterway Polypropylene 1 piece 5 years board Solenoid valve Polypropylene DC24V... -
Page 8: Installation And Commissioning
4. INSTALLATION AND COMMISSIONING _____________________________________________________________________________________________________________ • Please read all instructions and precautions before installing this product. • When selecting a mounting location of the system, take into consideration the length of tubing required for connections between existing plumbing and system components. Some installation sites may require more tubing than provided in the kit. • Open the package and check all the items in the “PARTS INCLUDED” list are there and without any apparent damage. • The installation instructions below serve only as a guide. The installation, commissioning and maintenance of this product must be carried out by qualified technicians designated by an authorized Pentair’ s distributor. Installation by unauthorized person may damage the product and damage so caused will not be covered by warranty. • Please contact your local Pentair authorized distributor for product installation, commissioning, maintenance and after-sales services. 4.1. Tools and Materials • Hand or electric drill (cordless preferred) • Multimeter • (2) Adjustable wrenches • Tester • Slotted and Phillips screwdrivers • Electric cable • File... -
Page 9: Installation Precautions And Requirements
4.2. Installation Precautions and Requirements • The product is provided with a booster pump. This product can be installed on the municipal tap water supply inlet pipe. • Accessible 110-220V power socket. • Install the product in a clean and hygienic location, with no surrounding pollution, away from direct sunlight, flammable and explosive materials or electrical equipment, and sheltered from rain. • The electrical circuit must be installed by certified professional personnel. • Turn off the main power supply and modify the circuit carefully according to the user’ s requirement. Such work must comply with relevant electrical installation procedures and regulations. • Upon completion of the modification, conduct a circuit check and clean up the area. 4.3. Quick Connect Instruction The water outlets connections of the product are equipped with quick connector ports. The quick connector port allows for quick and firm connections without the use of any tools. • Connecting and disconnecting the PE tube to the quick connector port When connecting, pull out the horseshoe shaped clip. Cut squarely across one end of the supplied PE tube and insert the cut end fully into the connector port. Ensure that the PE tube is inserted through the seal ring of the connector. Then, tug the PE tube slightly outward to generate a small gap between the moveable plastic ring and the port opening. Reinsert the horseshoe shaped clip onto the gap to complete the connection. Blue horseshoe shaped Remove the Push in the tube Tug slightly outward Reinsert the... -
Page 10: Installation Steps
• Installing the inlet 3-way ball valve: Clean the installation location before shutting the main water inlet valve. Then, dismantle the pipe faucet (simple faucet or angle valve) and install the 3-way ball valve in its place (note: threaded connections should be sealed with Teflon tape or washers). Lastly, re-connect the original faucet or angle valve. • Connecting to the water inlet: Connect one end of the PE tube to the ball valve connected to the municipal tap water pipe. Then connect the other end of the PE tube to the water inlet connecting port (marked as “Inlet”) on the main machine. • Installing the water purification system’s faucet: At the position where the faucet is to be installed, make a mark on the stainless steel sink with a hammer and center punch (to facilitate drilling). Drill a Φ 29mm (model: V3000-SEA) or Φ 12 mm (model: V15-SEA) hole with an electric drill and install the faucet. • Connection for clean (filtered) water (for model V3000-SEA only): Connect one end of the 1/4” straight quick-connector onto the faucet connector marked “Clean Water”. Cut an appropriate length of 1/4” PE tube and insert one end into the 1/4” straight quick-connector; then the other end into the clean water connector port on the water purification system. - Page 11 DRAIN CLEAN INLET PURE WATER WATER Faucet Wire (V3000-SEA ONLY) Power Supply Leak Protection DRAIN CLEAN WATER INLET PURE WATER (V3000-SEA only) • Connection for pure (RO) water: Connect one end of the 1/4” straight quick-connector onto the faucet connector marked “Pure Water”. Cut an appropriate length of 1/4” PE tube.Then insert one end into the 1/4” straight quick-connector and the other end into the pure water connector port on the water purification system. • Connection for drain water: Prepare an appropriate length of 3/8” PE tubing and connect it to the drain water connector port on the water purification system. Connect the other end to the drainage pipe, ensuring proper fitting to prevent it from falling out (note: the drain water should not be discharged into a tank without spill-over protection as overflowing may cause water spill).
-
Page 12: Operating Instructions
5. OPERATING INSTRUCTIONS _____________________________________________________________________________________________________________ NOTE: The reverse osmosis membrane is treated with a sanitizing agent to prevent microbial contamination, which should be flushed from the system. While using the system for the first time or replacing the reverse osmosis membrane (second-stage filter), it is recommended to perform rinsing for 60 minutes and soaking the RO membrane for 24 hours before using it normally. -
Page 13: Normal Operation
5.2. Normal Operation • During normal use, simply turn on the faucet. • After a prolonged period of non-use, flush the system until clear water is being dispensed out of the faucet. LED Screen Every time the power is turned on, the LED on the display will blink once. Thereafter, the machine goes into operation state. Every key pressed is acknowledged by an audible beep. If there is no operation for 5 minutes, the display will go into screen-saver mode. Pressing any key will wake up the display. The machine then immediately enters the operation state. Processing Flushing Leak Error Filter 1 Filter 2 Filter 3 Processing Flushing Leak Error SELECT FLUSH RESET Filter 1 Filter 2 Filter 3 SELECT FLUSH RESET *Front display panel color depends on model. -
Page 14: Water Purification System Monitoring
• Audio alarm is activated: 6 beeps. • After troubleshooting and resolving the fault, the machine will return to normal operation after the power is turned on again. • Error Icon and Text will not light up under normal operating conditions. • Press the “Reset” button or turn the power off and on again to resume normal operation. Leakage Detection If continuous monitoring of the leakage sensor reveals 10 consecutive leakage signals, the product will stop operating. The Leak Icon and Text will light up, and the audio alarm will sound 6 beeps. When the leakage fault is eliminated, the leakage alarm will cease and the machine automatically returns to normal operation. Dual Faucet (Model V3000-SEA only): • When the power is turned on, the Blue LED flashes once followed by the red LED. • Filter cartridge change reminder: When the lifespan of any of the filter cartridge falls below 5%, the blue LED on the faucet blinks whenever the machine is in water production mode, and stops blinking when the machine is on standby. • Filter cartridge lifespan is up: When the lifespan of any of the filter cartridge is up, the red LED on the faucet lights up whenever the machine is in water production mode. 6. MAINTENANCE AND CARE _____________________________________________________________________________________________________________ 6.1. Filter Cartridge Replacement Cycle Replace the filter cartridge according to the reminder for the corresponding filter cartridge on the water purification system. -
Page 15: Steps For Replacement Of Filter Cartridge
6.2. Steps for Replacement of Filter Cartridge Replace the filter cartridge according to the machine’ s lifespan reminder or the recommended replacement cycle. Please contact your local Pentair authorized distributor for replacement of filter cartridges. 1. Turn off power to the water purification system and shut the inlet 3-way ball valve. Open the faucet and discharge it until no more water flows out of the faucet. 2. Remove the top cover and put aside. The filter cartridge is built into the filter canister. Twist the filter cartridge anti-clockwise to remove it and clockwise to install the filter cartridge, as shown in the diagram below. Guide for Cartridge Installation Insert cartridge into the Press down the cartridge and turn it corresponding cartridge receptacle clockwise 60° until it clicks into the as shown in the diagram below. indicated position. The top of the cartridge should be flush with the surface of the internal frame. The direction of the cartridge is shown in the diagram below. The installation is completed. Cartridge Replacement Turn off the inlet water supply and unplug the power. Turn the cartridge anti-clockwise to the unlock position and remove the used cartridge. Install new cartridge according to the above Guide for Cartridge Installation. Twist anti-clockwise to remove, clockwise to install 3. Upon installation of the filter cartridges, open the inlet 3-way ball valve, turn the machine on and... -
Page 16: Troubleshooting
7. TROUBLESHOOTING _____________________________________________________________________________________________________________ Problem Possible Cause(s) Solution The system does not PE tube is bent Remove bend from PE tube produce water or Check if the three-way ball valve Open the three-way ball valve Reduced outlet water is closed flowrate Check if the inlet water supply is Wait for the inlet water supply to disrupted resume Check if filter cartridge 1 is clogged Replace filter cartridge 1 Check if the water pressure is Install a pressure booster lower than the rated pressure Check if the water temperature is too low The equipment does not Faulty power supply Check if there is power operate Faulty power adapter Replace the power adapter The equipment does not have Check if there is water flowing from water supply the source. Once there is water, turn the power off and on to restart. Abnormal taste Check if the machine has not been Flush the filter cartridges (except used for a long period of time... -
Page 17: Terms And Conditions Of Warranty
8. TERMS AND CONDITIONS OF WARRANTY _____________________________________________________________________________________________________________ (1) The warranty period is 1 year from the date of purchase. During the warranty period, Pentair (Company) is responsible for providing free warranty for faults arising from normal operation and use according to the installation manual and user’ s manual. Pentair will charge repair and maintenance fees after the warranty expires. (2) The user should keep valid purchase invoice, which serves as the basis for after-sales service. (3) Installation, maintenance and repair services will be provided by Pentair’ s authorized distributors. In the event that the user is unable to present the warranty card or valid purchase invoice, Pentair will deem the warranty to have expired and charge the relevant fees. (4) Warranty will be void in the following conditions: • Installation by personnel who are not authorized by Pentair; • Product malfunction or damage resulting from user’ s failure to follow the instructions described in user’ s manual to operate the system; • Error or damage caused by the user’ s self-repair or modification of the equipment; • Error or damage caused by force majeure (including but not limited to natural disasters such as fires, floods, earthquakes, lightning strikes, etc.);... - Page 18 Distribution and Service by: (Distributor Stamp Here) Date of Purchase: 371 He Shan Road | New District Suzhou | Jiangsu 215011 | China | pentair.com All Pentair trademarks and logos are owned by Pentair. All other brands or product names are trademarks or registered marks of their respective owners. Because we are continuously improving our products and services, Pentair reserves the right to change specifications without prior notice. 00-00000 00/00 ©2020 Pentair. All Rights Reserved.
Need help?
Do you have a question about the V3000-SEA and is the answer not in the manual?
Questions and answers