Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Holzstar DB 450
Summary of Contents for Holzstar DB 450
- Page 1 Instruction Manual Wood Lathe DB 450 DB 450...
-
Page 2: Table Of Contents
Contraventions are liable to compensa- 14 Spare parts..........16 tion. 14.1 Spare parts orders ........... 16 14.2 Spare parts drawing DB 450......17 Subject to technical modifications and error. 15 Electrical Schematic......18 16 EC Declaration of Conformity....19 DB 450 | Version 4.07... -
Page 3: Introduction
WARNING! even further. This combination of symbol and signal term indi- cates potentially hazardous situations which may cause death or serious injury if not averted. DB 450 | Version 4.07... -
Page 4: Obligations Of The Operating Company
These must be implemented in the form of opera- ting instructions for the operation of the machine. DB 450 | Version 4.07... -
Page 5: Personal Protective Equipment
Ear protection until new signs have been attached. The ear protection protects against hearing damage caused by noise. Eye protection Protective glasses protect the eyes against projected parts and splashes of liquid. DB 450 | Version 4.07... -
Page 6: Safety Instructions
Protect the cable from heat, oil - Wear a dust mask to protect yourself from wood and sharp edges. dust. - Prevent the tool from being hooked in during ma- chining DB 450 | Version 4.07... -
Page 7: Intended Use
Intended Use damage to persons or objects and invalidate the war- ranty claim! The Wood Lathe DB 450 is used exclusively for turning 3.1 Residual risks wood or wood-like materials whose max. Turning diame- ter is 250 mm. The max. Tip width of the workpiece is 450 mm (which can be optionally extended to 1000 mm). -
Page 8: Technical Data
The removal of danger spots, disturbances and unevenness at the time of trans- port by other employees leads to considerable dangers. Fig. 2: Type plate DB 450 Careful planning of internal transport is therefore essen- tial. -
Page 9: Packaging
- Tailstock - Revolving center of gravity - Turning steel edition - Instruction manual 5.5 Accessories, not included Fig. 4: Wood Lathe DB 450 1. Headstock with cover 2. Plate 3. Face driver 4. Tool rest 5. Clamping the height adjustment 6. -
Page 10: Setting Up And Connection
Degrease the cone seats on the two centering points the operating personnel, for material transport as well and insert them by hand. The revolving centering point as for adjustment and maintenance work. should be placed in the tailstock (Fig.6). DB 450 | Version 4.07... -
Page 11: Electrical Connection
Place the belt on a different pair of Before starting the machine, execute a few sample revo- discs to change the speed (RPM). lutions on the handwheel (Pos. 4, fig. 8) to avoid collisi- ons. DB 450 | Version 4.07... -
Page 12: Adjusting The Tool Rest
- In addition, guides, sleeves and bearings must be lubricated or oiled with commercially available lubri- cating grease! DB 450 | Version 4.07... -
Page 13: Working Instructions
The contact details can be found in chapter 1.2 Customer Service. Please consider the following points: 1. All protective and safety equipment must be reinstal- led immediately after repair and maintenance work has been completed. DB 450 | Version 4.07... -
Page 14: Lubrication
12 Disposal, recycling of old equipment In your own interests and in the interests of the environ- ment, please ensure that all components of the machine are disposed of in the proper and approved way. DB 450 | Version 4.07... -
Page 15: Troubleshooting
Motor is connected incor- Let it checked by a specialist. rectly. Insufficient working Uneven, heavy or clamped Clamp workpiece mass-balanced and tension-free. accuracy workpiece. Incorrect horizontal position Adjust the tool rest. of the tool rest. DB 450 | Version 4.07... -
Page 16: Spare Parts
Spare parts 14 Spare parts Example The drive belt for the Wood Lathe DB 450 must be or- DANGER! dered. The drive belt has the number 26 in the spare parts drawing 1. Risk of injury caused by the use of... -
Page 17: Spare Parts Drawing Db 450
The following spare parts drawing is intended to help identify the necessary spare parts. To order, please send a copy of the list of spare parts with the marked components to your dealer. Machine bed extension (Optional) Fig. 10: Spare Parts Drawing DB 450 DB 450 | Version 4.07... -
Page 18: Electrical Schematic
Electrical Schematic 15 Electrical Schematic Fig. 11: Electrical schematic DB 450 DB 450 | Version 4.07... -
Page 19: Ec Declaration Of Conformity
Safety of woodworking machines - Chip and dust extraction systems with fixed installation - Safety requirements Responsible for documentation: Kilian Stürmer, Stürmer Maschinen GmbH, Dr.-Robert-Pfleger-Straße 26, D-96103 Hallstadt Hallstadt, den 13.04.2016 ______________________ Kilian Stürmer Managing Director DB 450 | Version 4.07... - Page 20 www.holzstar.de...
Need help?
Do you have a question about the DB 450 and is the answer not in the manual?
Questions and answers