Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Holzstar DB 1102 VARIO
Summary of Contents for Holzstar DB 1102 VARIO
- Page 1 Instruction Manual Wood Lathe DB 1102 VARIO DB 1102 VARIO...
- Page 2 15 Spare parts .......... 20 tion. 15.1 Ordering spare parts........20 Subject to technical modifications and error. 15.2 Spare parts drawings DB 1102 VARIO..21 16 Electrical circuit diagram ....23 17 EC Declaration of Conformity .... 24 DB 1102 VARIO | Version 1.05...
- Page 3 This combination of symbol and signal term indi- could be shared and be valuable to develop our-products cates potentially hazardous situations which may even further. cause death or serious injury if not averted. DB 1102 VARIO | Version 1.05...
- Page 4 He must implement these in the form of operating in- structions for the operation of the machine. DB 1102 VARIO | Version 1.05...
- Page 5 In addition, the operator must also consider other aspects of the danger in relation to the environmental conditions and the material. DB 1102 VARIO | Version 1.05...
- Page 6 - No changes may be made to the machine. - Perform regular inspections according to the in- The Wood Lathe DB 1102 VARIO is designed exclusi- structions in the manual. vely for turning wood or wood-like materials. All specified - Make sure that no user-caused malfunctions can data (see chapter "Technical Data") must be observed.
- Page 7 Control of the speed Electronic variable regulation Taper of tailstock sleeve Travel of tailstock 102 mm sleeve Motor power output 1,5 kW Rated current 4.1 Type plate Fig. 2: Type plate DB 1102 VARIO DB 1102 VARIO | Version 1.05...
- Page 8 WARNING: DANGER OF TIPPING The device may be lifted unsecured by a maximum of 2cm. Employees must be outside the danger zone, the reach of loads. Warn employees and, if necessary, advise employ- ees of the hazard. DB 1102 VARIO | Version 1.05...
- Page 9 1 - Speed indicator The currently set speed is displayed here. 2 - Emergency stop button Fig. 3: Wood Lathe DB 1102 VARIO 1 Protective cover spindle 2 Control panel Stops the motor when it is pushed in. Prevents restarting until 3 Workpiece holder it is reset.
- Page 10 Step 1: Unpack the machine and check for complete- ness and damage. Step 2: Lift the machine onto the machine frame with the help of a second person. Step 3: Fasten the machine to the machine frame with 8 Allen screws DB 1102 VARIO | Version 1.05...
- Page 11 Fasten the lathe to the ground using the holes provided in the machine frame. Step 1: Plug the plug into a 230V power outlet. Step 2: The machine is now ready for operation. Drilling Bohrungen Fig. 8: Drilling DB 1102 VARIO | Version 1.05...
- Page 12 Other persons must stay away from the work 10.3 Speed variation with speed area during operation. controller You can continuously adjust the speed of the lathe in two Wear ear protection! speed ranges. DB 1102 VARIO | Version 1.05...
- Page 13 Step 7: Loosen the motor mounting screw (Fig.11) Step 8: Push down the motor tensioning handle to ten- sion the drive belt. DB 1102 VARIO | Version 1.05...
- Page 14 With the lathe you also have the possibility to move or chine bed. swivel the headstock on the machine bed. DANGER! Always operate the lathe with the headstock firmly locked to the bed. Failure to do so may result in se- rious injury. DB 1102 VARIO | Version 1.05...
- Page 15 Step 4: Release the pivot bolt (Fig.19) to lock the head- stock. Make sure that the pin is inserted into the headstock engages. DB 1102 VARIO | Version 1.05...
- Page 16 Workpieces made of glued wood should the points. only be processed by an experienced craftsman. DB 1102 VARIO | Version 1.05...
- Page 17 A functional test should be carried out before each use. - Connections and repairs to the electrical equip-ment The drive belt must be under tension. may only be carried out by a qualified electrician. Check the direction of rotation of the workpiece. DB 1102 VARIO | Version 1.05...
- Page 18 Step 9: Tension the belt. Step 10: Replace the spindle cover and the access flaps. Spindle cover Belt access Fig. 25: Change drive belt Step 3: Remove the spindle cover and the two hexago- nal bolts. DB 1102 VARIO | Version 1.05...
- Page 19 Step 1: Remove all environmentally hazardous fluids If necessary, the help of a specialized waste manage- from the old machine. ment company can be used for the treatment. DB 1102 VARIO | Version 1.05...
- Page 20 By helping to properly dispose of this product, you are protecting the environment and the health of others. The engine for the Wood Lathe DB 1102 VARIO must be Environment and health are endangered by improper ordered. The engine has the number 61 in the spare disposal.
- Page 21 The following spare parts drawings is intended to help identify the necessary spare parts. To order, please send a copy of the list of spare parts with the marked components to your dealer. Spare parts drawing 1 Fig. 27: Spare parts drawing 1 Wood Lathe DB 1102 VARIO DB 1102 VARIO | Version 1.05...
- Page 22 Spare parts Spare parts drawing 2 Fig. 28: Spare parts drawing 2 Wood Lathe DB 1102 VARIO DB 1102 VARIO | Version 1.05...
- Page 23 Electrical circuit diagram 16 Electrical circuit diagram Fig. 29: Electrical circuit diagram DB 1102 VARIO DB 1102 VARIO | Version 1.05...
- Page 24 ≤ 16 A per phase and not subject to conditional connection Responsible for documentation: Kilian Stürmer, Stürmer Maschinen GmbH, Dr.-Robert-Pfleger-Str. 26, D-96103 Hallstadt Hallstadt, 03.03.2021 ______________________ Kilian Stürmer Geschäftsführer DB 1102 VARIO | Version 1.05...
- Page 25 Notes 18 Notes DB 1102 VARIO | Version 1.05...
- Page 26 www.holzstar.de...
Need help?
Do you have a question about the DB 1102 VARIO and is the answer not in the manual?
Questions and answers