Table of Contents
Advertisement
Quick Links
Functions compatible with the 2016 Jeep Patriot
Arm Factory Security
Brake Status (foot brake)
Control of aftermarket alarm with OEM remote
Disarm Factory Security
Door Lock Control
Door Unlock
Driver Priority Unlock
E-Brake Status
Entry Monitoring ALL Door Pins
Entry Monitoring Hood Pin
Entry Monitoring Trunk/Hatch Pin
Fuel level/EV battery level
Ignition Status
Immobilizer Bypass-Data No Key Req'd
Parking Lights Control
RAP Shut Down (Retained ACC Power)
Remote Start Ready
Remote Start Takeover
SmartStart
Tach / RPM Output
403.CHRYSLER
v7.36
2016 Jeep Patriot
CHTHD2, THCHD2 Compatible
(Sold Separately)
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Voxx Electronics DEI 403.CHRYSLER
Summary of Contents for Voxx Electronics DEI 403.CHRYSLER
- Page 1 403.CHRYSLER v7.36 2016 Jeep Patriot CHTHD2, THCHD2 Compatible (Sold Separately) Functions compatible with the 2016 Jeep Patriot Arm Factory Security Entry Monitoring Trunk/Hatch Pin Brake Status (foot brake) Fuel level/EV battery level Control of aftermarket alarm with OEM remote Ignition Status Disarm Factory Security Immobilizer Bypass-Data No Key Req'd Door Lock Control...
-
Page 2: Table Of Contents
Contents Introduction Pre-installation and application warnings Installation Wiring diagram with T-Harness CHTHD2 (R1-R7 & R9-R10) or THCHD2 (R1) Wiring diagram Locating components in the vehicle Vehicle connections Module programming Key-type Vehicles Push-to-Start (PTS) Vehicles Connecting the module LED diagnostics and troubleshooting Soft reset Hard reset Feature programming... -
Page 3: Introduction
Introduction DB3 is an all-in-one door lock and override module. Warning! This module can only be flashed and configured using DirectLink at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to “Connecting the module” for more information. 403.CHRYSLER 7.36 2016 Jeep Patriot ©2023 Directed. -
Page 4: Pre-Installation And Application Warnings
Pre-installation and application warnings This section highlights important information for this specific firmware and will assist in pricing accordingly, as START HERE well as bringing awareness to any operational or vehicle limitations. Compatibilities and Requirements T-Harness Keys required for Keys required CHTHD2/THCHD2 programming for operation... -
Page 5: Wiring Diagram With T-Harness Chthd2 (R1-R7 & R9-R10) Or Thchd2 (R1)
Wiring diagram with T-Harness CHTHD2 (R1-R6 & R9-R10) or THCHD2 (R1 & R11) Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( only To 8-pin female connector Sentry Key Module at the ignition switch (black 8-pin conn.) -
Page 6: Wiring Diagram
Wiring diagram Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( (+) Ignition: Pink or Pink/White, pin 3 XKD2D65 (MUX) Ignition: Violet/Brown, pin 1 CAN B Low: White or White/Pink, pin 7 Sentry Key Module (black 8-pin conn., connector side view) -
Page 7: Locating Components In The Vehicle
Locating components in the vehicle 403.CHRYSLER 7.36 2016 Jeep Patriot ©2023 Directed. All rights reserved. -
Page 8: Vehicle Connections
Vehicle connections The connection information listed below is specific to the 2016 Jeep Patriot. Refer to “Pre-installation and application warnings” for a list of important notes. Data 14-pin blue connector (H1) Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color H1/1 Light Green... - Page 9 Input 10-pin black connector (H3) Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color H3/1 Green (-) W2W Only - Lock Input Remote Starter H3/2 Blue (-) W2W Only - Unlock Input Remote Starter H3/3 Red/White (-) W2W Only - Trunk Input Remote Starter H3/4 White/Violet...
-
Page 10: Module Programming
Module programming Refer to “LED diagnostics and troubleshooting” for more information and for troubleshooting purposes. Key-type Vehicles Ensure vehicle is in a safe location and cannot move forward during programming. For vehicles equipped with a manual transmission, make sure the gearshift is in the neutral position. -
Page 11: Push-To-Start (Pts) Vehicles
Push-to-Start (PTS) Vehicles Ensure vehicle is in a safe location and cannot move forward during programming. For vehicles equipped with a manual transmission, make sure the gearshift is in the neutral position. The harnesses must be connected in this exact order: ... - Page 12 You have successfully completed the module programming sequence. 403.CHRYSLER 7.36 2016 Jeep Patriot ©2023 Directed. All rights reserved.
-
Page 13: Connecting The Module
Connecting the module Important! Make all the required connections to the vehicle, as described in this guide, and double-check to ensure everything is in order before moving onto the programming. Warning! To take advantage of advanced features, you must use DirectLink 4.5 (and higher) or the Directechs Mobile application. To flash a module using your computer: Connect the interface module to your computer using the XKLoader2. -
Page 14: Led Diagnostics And Troubleshooting
LED diagnostics and troubleshooting This section provides LED diagnostics and troubleshooting information to guide you through the various stages of your installation. Module Programming Description Troubleshooting Make sure the D2D harness is connected and that 12 Volt is present between the red and black wires. If Module has no power. - Page 15 Active Ground When Running (Status) Description Troubleshooting Ground When Running (Status) command The module has initialized the remote start sequence. received. Flashes green Ignition ON command received. The module has received the Ignition ON command and is processing the remote start sequence. Flashes red &...
-
Page 16: Soft Reset
Soft reset A module reset will only erase the steps perfomed in “Module Programming”. The firmware and settings flashed to the module will not be affected. D2D installation Connect the 10-pin, 12-pin & 14-pin harnesses to the module. Press and hold the programming button, then connect the 4-pin D2D harness. (12-pin) (D2D) (Button) -
Page 17: Feature Programming
Feature programming To enter feature programming routine: Turn the ignition ON, then OFF. 2. Within 5 seconds, press and hold the programming button until the LED turns ON orange (after 3 seconds). 3. Release the programming button. The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate the current option of feature 1 (e.g. -
Page 18: Feature And Option List
Feature and option list Depending on your vehicle, some of the features and options listed below may need to be configured using the configuration tool found on the module flashing page at www.directechs.com. The web offers more options; however, manual configuration of the features is possible using the information on this page. -
Page 19: Limited One Year Consumer Warranty
Limited 12 Months Consumer Warranty VOXX DEI LLC (the Company) warrants to the original purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 12 months from the date of original purchase, such defect(s) will be repaired or replaced with new or reconditioned product, (at the Company’s option) without charge for parts or repair labor. -
Page 20: Quick Reference Guide (Customer Copy)
Quick Reference Guide (customer copy) Sending commands to your vehicle Pit stop/idle mode Whether you want to remote start the engine, lock/unlock the doors or pop the trunk, there Stop the vehicle in a safe parking spot and put the gear gear in are 3 possible ways you can send commands to your vehicle, using the: in Park (P). - Page 21 403.CHRYSLER 7.36 2016 Jeep Patriot ©2023 Directed. All rights reserved.
Need help?
Do you have a question about the DEI 403.CHRYSLER and is the answer not in the manual?
Questions and answers