Frigidaire GAM155Q1A - GIBSON 15100BTU 115V 12.5A 10.3 SPD 4 WAY AIR DIRECTION Installation Instructions Manual

Heavy duty (fas models) and median (fam models) air conditioners
Hide thumbs

Advertisement

For Heavy Duty (FAS Models) and
Median (FAM Models) Air Conditioners
Please read ALL instructions before installing. Two people are
recommended to install this product. If a new electrical outlet
is required, have the outlet installed by a qualified electrician
before installing unit. See#5 in Preliminary Instructions
following.

Preliminary Instructions

Do the following before starting to install unit. See illustrations
below.
Check dimensions of your unit to determine model type:
Heavy duty (FAS)
Unit Height:
18 5/8"
Unit Width:
Min. Window Opening:
Min. Window Width:
Max. Window Width:
1. Check window opening size - the mounting parts furnished
with this air conditioner are made to install in a wooden
sill double-hung window. The standard parts are for
window dimensions listed above. Open sash to a minimum
of 19''(483mm). (FIG. 1)
2. Check condition of window - all wood parts of window
must be in good shape and able to firmly hold the needed
screws. If not, make repairs before installing unit.
FIG. 1
STORM WINDOW FRAM E OR
OTHER OBSTRUCTION

Installation Instructions

Median (FAM)
17 5/8"
26 ½"
23 ½"
19"
18 ½"
31"
26 ½"
43"
40 ½"
SAFETY LOCK AND
3/4'' LONG HEX HEAD
SCREW
3. Check your storm windows - if your storm window
frame does not allow the clearance required, correct by
adding a piece of wood as shown in FIG. 2, or by removing
storm window while room air conditioner is being installed.
(continued)
STORM WINDOW FRAME OR
OTHER OBSTRUCTION
1
BOARD THICKNESS AS
REQUIRED, ALONG
ENTIRE STOOL. FASTEN
WITH TWO NAILS OR
SCREWS.
P/N 220219A032

Advertisement

loading

  Also See for Frigidaire GAM155Q1A - GIBSON 15100BTU 115V 12.5A 10.3 SPD 4 WAY AIR DIRECTION

  Related Manuals for Frigidaire GAM155Q1A - GIBSON 15100BTU 115V 12.5A 10.3 SPD 4 WAY AIR DIRECTION

  Summary of Contents for Frigidaire GAM155Q1A - GIBSON 15100BTU 115V 12.5A 10.3 SPD 4 WAY AIR DIRECTION

  • Page 1: Preliminary Instructions

    2. Check condition of window - all wood parts of window adding a piece of wood as shown in FIG. 2, or by removing must be in good shape and able to firmly hold the needed storm window while room air conditioner is being installed.
  • Page 2: Tools Required

    All models have a 3-prong service plug to provide proper service and safe positive grouding. Do not change plug in Hardware (in plastic bag) any way. Do not use an adapter plug. If your present wall outlet does not match your plug, call a qualified electrician Qty.
  • Page 3: Remove Chassis

    4. Pry away front from cabinet sides as per photo (See FIG. 3). to cabinet as 5. Gently lift front off unit and place to one side (See FIG. 4). shown in FIG. 6. FIG. 4 FIG. 3...
  • Page 4: Install Support Bracket

    4. Insert washer head locking screws (2) into holes in and tight to bottom of cabinet as shown below. Mark top leg of f iller panel frame (see Step 6). Do not totally brackets at top level of sill, and remove.
  • Page 5 Loosen screws so filler panels slide easily. leaving 6” protruding. DO not push on controls OR finned coils. CAUTION 3. Be sure chassis is firmly seated towards rear of cabinet. LOCKING SCREWS Installation of front is the reverse of removal outlined in Section 1.
  • Page 6: Thru-The-Wall Installation

    5. Nail frame to spacers to spacers with front flush with nails). drywall. 2. Cut or knock out a hole on each side of center stud. 3. Measure between inside edges of every other stud as shown NAIL SPACERS TO STUDS in FIG.
  • Page 7 NOTE: If wall thickness is 8-1/2'' or more, add aluminum flashing over bottom of frame opening to assure no water can FIG. 2 enter area between inner and outer wall. 1'' LONG WOOD SCREW CAULK AS REQUIRED Refer to Step 4 of Window Mounting for assembly of support brackets.
  • Page 8: Masonry Construction

    You can buy wood from your local lumber or hardware supply. On the outside, caulk openings around top and sides of cabinet, and all sides of wood sleeve to the opening. NOTE: See Step 7, Item 3 of Window Mounting Instructions for bottom rail seal location.