Download Print this page
Frigidaire GAH085Q1T - GIBSON 8000BTU 115V 8.0A 9.4EE3 SPD 4 WAY AIR DIRECTION Installation Instructions Manual
Frigidaire GAH085Q1T - GIBSON 8000BTU 115V 8.0A 9.4EE3 SPD 4 WAY AIR DIRECTION Installation Instructions Manual

Frigidaire GAH085Q1T - GIBSON 8000BTU 115V 8.0A 9.4EE3 SPD 4 WAY AIR DIRECTION Installation Instructions Manual

Installation instructions
Hide thumbs Also See for GAH085Q1T - GIBSON 8000BTU 115V 8.0A 9.4EE3 SPD 4 WAY AIR DIRECTION:

Advertisement

Installation Instructions

Do This First
(for existing sleeve)
Note that the air conditioner dimensions are: 24 wide,
14
1
high, and 22
deep (without front). Install Air
2
Conditioner according to these installation instructions
to achieve the best performance. Save these installation
instructions for future reference.
Items in Kit
You may not need all parts in the kit. Discard unused
parts.
Tapered Spacer Blocks
Centering/Support Blocks
Plastic Divider
Stuffer Seal
Seal
Seal
Seal
Seal
Seal
Trim Frame (side legs)
Trim Frame (top & bottom legs)
Ground Wire (green)
Nut for grounding screw
Grounding Screw
Grille (plastic)
Grille Aluminum
Nuts (plastic)
Screw w/washer

How to Install

1. Identify the wall-sleeve brand for your installation,
from the chart below.
Brand
White-Westinghouse
}
Frigidaire
Carrier (52F Series)
General Electric/
Hotpoint
Whirlpool
Fedders/Emerson
Sears/Kenmore
Emerson/Fedders
Carrier (51S Series)
Friedrich
NOTE: All wall sleeves used to mount the new Air
Conditioner must be in sound structural condition and
have a rear grille that securely attaches to sleeve, or
rear flange that serves as a stop for the Air Conditioner.
17 Long
4
1
x 3
1
x 1
1
2
2
2
1/8" x 4
1
x 14
1
2
2
1 x 1
1
"x 84
2
1
1
x 1
1
x 25
2
2
1
1
x 1
1
x 14
2
2
1
1
x 3/8 x 25
2
1
1
x 3/8 x 14
2
1" x 3/4 x 14
Wall Sleeve Dimensions
(inches)
Width
Height
Depth
25
1
15
1
16, 17
2
4
or 22
26
15
5
8
25
16
7
1
8
2
or 23
27
16
3
4
or 19
25
3
16
7
4
8
26
15
3
3
4
4
25
3
16
7
4
8
27
16
3
4
CAUTION: When installation is complete, replacement
unit MUST have a rearward
slope as shown.
2. Remove old Air Conditioner from wall sleeve and
prepare wall sleeve as follows:
— Clean interior (do not disturb seals).
Qty.
— Wall sleeve must be securely fastened in wall before
2
installing Air Conditioner. Drive more nails or screws
2
through sleeve, into wall, if needed.
1
— Repair paint if needed.
1
2
3. If not existing, drill a 3/16 clearance hole for ground-
2
ing screw through left side of wall sleeve, in a clear area
2
about 3 inches maximum (to suit) back from front edge
2
of sleeve as shown below. Next attach ground wire inside
1
sleeve, using grounding screw, nut washer pull loose
2
end of ground wire out front of sleeve, and temporarily
2
bend it down and around lower edge of sleeve.
1
1
1
1
Wall sleeve to unit
1
sleeve grounding
4
4
4. Prepare the wall sleeve for installation of the new unit
per the following Brand instructions.
#1 Emerson
#2 Fedders
#3 Fedders or Friedrich
#4 General Electric/Hotpoint
1
2
#5 Sears or Carrier (51S Series)
#6 Whirlpool
#7 Whirlpool
16
7
8
#8 White-Westinghouse/Frigidaire/
17
1
8
Carrier (52F Series)
#9 White-Westinghouse/Frigidaire
16
3
4
3
4
5. Install new unit into wall sleeve.
18
5
8
15
6. To attach ground wire to the new unit, remove the
18
5
8
screw from the left side front.
16
3
4
7. Assemble and install the
Trim Frame (see instruction).
1
1/4" to 5/16"
Wa l l
S l e e v e
UNIT
REAR
3"
Max.
1"
15 Deep
19
3
Deep
4
16
3
Deep
4
16
7
Deep
8
18
5
Deep
8
17
1
8
23 Deep
16 + 17
22 Deep
P/N 220218A029
FRONT
LEVEL
3
/
16 "
Hole
Deep
1
Deep
2

Advertisement

loading
Need help?

Need help?

Do you have a question about the GAH085Q1T - GIBSON 8000BTU 115V 8.0A 9.4EE3 SPD 4 WAY AIR DIRECTION and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Frigidaire GAH085Q1T - GIBSON 8000BTU 115V 8.0A 9.4EE3 SPD 4 WAY AIR DIRECTION

  • Page 1: Installation Instructions

    3. If not existing, drill a 3/16 clearance hole for ground- Seal ⁄ ⁄ x 14 ing screw through left side of wall sleeve, in a clear area Seal ⁄ x 3/8 x 25 about 3 inches maximum (to suit) back from front edge Seal ⁄...
  • Page 2 It is very important that these installation instructions are followed so your unit can operate at maximum efficiency. If this is an existing sleeve, and there is an existing rear grille, the louvers will have to be bent as per the instructions at the beginning of each section.
  • Page 3 The use of pliers is recommended. 7" Top View 2. Attach (1) 1 ½” x 3/8” x 25” long seal in the center at the top of the sleeve. Remove the backing paper and press into position. 3. Attach (2) 1 ½” x 3/8” x 14” seals to the left and right sides of the sleeve.
  • Page 4 6. Attach (2) 1 ½” x 3/8” x 14” seals to the left and right sides of the sleeve. 7. Cut the 1 ½” x 3/8” x 25” long seal to 14” long and attach it to the vertical section of the rear grille as shown.
  • Page 5 6. Attach (2) 1 ½” x 3/8” x 14” seals to the left and right sides of the sleeve. 7. Cut the 1 ½” x 3/8” x 25” long seal to 14” long and attach it to the vertical section of the rear grille as shown.
  • Page 6 3. Install as shown with the tapered end ½” from the back of the sleeve. This helps induce a rearward slope on the unit. 4. Attach (1) 1 ½” x 3/8” x 25” long seal in the center at the top of the sleeve. Remove the backing paper and press into position.
  • Page 7 3. Install as shown with the tapered end ½” from the back of the sleeve. This helps induce a rearward slope on the unit. 4. Attach (1) 1 ½” x 3/8” x 25” long seal in the center at the top of the sleeve. Remove the backing paper and press into position.
  • Page 8 5. Attach (2) 1 ½” x 3/8” x 14” seals to the left and right sides of the sleeve. 6. Cut the 1 ½” x 3/8” x 25” long seal to 14” long and attach it to the vertical section of the rear grille as shown.
  • Page 9 5. Attach (2) 1 ½” x 1 ½” x 14” seals to the left and right sides of the sleeve. 6. Cut the 1 ½” x 1 ½” x 25” long seal to 14” long and attach it vertically to the rear grill 7” from the left side.
  • Page 10 Place the grille against the rear flanges and use the (4) large washers and screws to secure the grille. 2. Attach (1) 1 ½” x 3/8” x 25” long seal in the center at the top of the sleeve. Remove the backing paper and press into position.
  • Page 11 10. Install the divider into the slots of the foam blocks. You may need to trim the length to size. 11. Cut to fit the 1 ½” x 1 ½” x 25” seal to fit the top of the sleeve. The pieces must be fitted flush to the edge of the divider.
  • Page 12: Finishing Installation

    FINISHING INSTALLATION: 1. Install the 1” x 1 ½” x 84” long stuffer-seal between the wall-sleeve and the unit. A flat-bladed screwdriver or putty knife is recommended. 2. Assemble the trim frame by inserting top and bottom peieces into side pieces and snapping into place.