Download
Share
Print this page
Watts ENWARE FS012ADJ Installation And Maintenance Instructions Manual
  1. Manuals
  2. Brands
  3. Watts Manuals
  4. Plumbing Product
  5. ENWARE FS012ADJ
  6. Installation and maintenance instructions manual
Watts ENWARE FS012ADJ Installation And Maintenance Instructions Manual

Watts ENWARE FS012ADJ Installation And Maintenance Instructions Manual

Hob mounted adjustable exposed mixer base
Hide thumbs
1
2
3
4
5
6
7
8

Advertisement

Quick Links

Download this manual
Hob Mounted Adjustable Exposed Mixer
Base
Installation and Maintenance Instructions
FS012ADJ
technical data
Working Pressure Range
Maximum Static Pressure
Maximum Working Temperature
Inlet Connection
Enware products are to be installed in accordance with the Plumbing Code of Australia (PCA) and AS/NZS3500.
Installations not complying with PCA and AS/NZS 3500 may void the product and performance warranty provisions.
Reference should also be made to the Australasian Health Facility Guidelines (AHFG), ABCB and Local Government
regulations when considering the choice of, and the installation of these products.
This product must be installed and commissioned by a qualified plumber.
For use with potable water only.
NOTE: Enware Australia advises:
1. Due to ongoing Research and Development, specifications may change without notice.
2. Component specifications may change on some export models.
I00616_16 Feb 2024
1300 369 273 | info@enware.com.au | enware.com.au
Min 50 kPa
Max 500 kPa
1200 kPa
95°C (Jumper Valve)
1/2" BSP

Advertisement

loading
Need help?

Need help?

Do you have a question about the ENWARE FS012ADJ and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Watts ENWARE FS012ADJ

Summary of Contents for Watts ENWARE FS012ADJ

  • Page 1 Hob Mounted Adjustable Exposed Mixer Base Installation and Maintenance Instructions FS012ADJ technical data Working Pressure Range Min 50 kPa Max 500 kPa Maximum Static Pressure 1200 kPa Maximum Working Temperature 95°C (Jumper Valve) Inlet Connection 1/2” BSP Enware products are to be installed in accordance with the Plumbing Code of Australia (PCA) and AS/NZS3500. Installations not complying with PCA and AS/NZS 3500 may void the product and performance warranty provisions.

  • Page 2: Before Installation

    installation BEFORE INSTALLATION • Ensure all operating and dimensional specifications are suitable for the intended installation. Check that there is no shelf or obstruction above. Shorter riser, hose & spring guard options are available from Enware • Check that wall bracket can be installed on a stable wall surface. If not, extra measures may need to be taken so that the bracket can be supported by a firm wall backing.
  • Page 3 2. Measure the centres of tap holes on bench, subtract 25mm from each end and mark this on each end of the breeching piece. Cut the breeching piece to the required length using tube cutters or similar hand tool. SEE IMAGE 02 3.
  • Page 4 FITTING LEVER HANDLES Fit colour indicator ring onto lever handle. To do this, place an indicator ring on flat surface with the rebated edge facing up. Fit spline adaptor onto Press the lever handle down onto TOOTH spindle. WASHER the indicator ring evenly until it clips into place.
  • Page 5 operating instructions OPERATING LEVER TAP To operate tap, turn handle lever in the directions indicated. Mixing Set (top view) Anti-Clockwise to close Clockwise to close WARNING Hot water will scald. Care must be taken to avoid scalding when using the trigger spray to deliver hot water.

  • Page 6: Maintenance

    maintenance CLEANING Enware products should be cleaned with a soft damp cloth using only mild liquid detergent or soap and water. Do not use cleaning agents containing a corrosive acid, scouring agent or solvent chemicals. Do not use cream cleaners, as they are abrasive. Use of unsuitable cleaning agents may damage the surface.

  • Page 7: Spare Parts

    spare parts Description Enware Part Code O-rings (8), grub screws (4), & aerator (1) pack FS734 Lever handle with colour indicators FSJ378 (for new/old style lever handle) Lever Top Assembly (includes lever handle, Hot, Cold, Warm & Hob Mount / Wall Mount / Pot Filler (Pillar / Bib) - grey indicators, fixing screw &...

  • Page 8: Product Warranty Statement

    - WATTS AUSTRALIA EFFECTIVE FROM 20 November 2023 3. Our responsibilities This Warranty Statement applies to products supplied by Australian Valve (a) In the event that the Supplier is reasonably satisfied that there is a Group Pty Ltd (ACN 068 227 270) (AVG) or Enware Pty Ltd (ACN 662...