OttLite J8600C Manual

LED Cone Clip Lamp
J8600C J8608C
INS-16-0296
ENGLISH
CONGRATULATIONS!
You've purchased the finest in natural lighting technology
with your new OttLite
PRODUCT REGISTRATION FORM
Please complete the enclosed Product Registration Form
and return it today by mail, or register online by going to:
www.warranty.ottlite.com
NOTE: THIS UNIT IS FULLY ASSEMBLED
1. Remove lamp from packing for use on a horizontal
table.
2. To use on standard table, mount lamp body clip (A)
on the preferred edge of the table.
3. Grasp by flex-neck (B) and back of body clamp,
squeeze clamp mechanism and slide onto table edge.
Clip must fully touch table surface.
B
4. Verify the lamp is secure before using.
5. Plug the cord into a standard household 120V AC
outlet.
6. Turn the lamp ON & OFF using power switch (C)
located near plug.
7. To position the shade simply bend the Flex-Neck (B)
as needed to point the light. To avoid damaging the
lamp, DO NOT force the Flex-Neck into a sharp bend.
SAFETY WARNING: TO REDUCE THE RISK OF
FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS
A
1. Turn off/unplug and WAIT UNTIL BULB / LAMP
HEAD IS COOL before handling.
2. Bulb gets hot quickly! Touch only switch/plug when
turning ON or OFF.
3. Never use with an extension cord unless the plug can
be fully inserted into the receptacles in the extension
cord.
4. Do not alter the plug.
5. The bulb included with this unit cannot be replaced by
the consumer.
C
Enjoy your OttLite
NOTE: The important safety instructions appearing in
this instruction sheet are not meant to cover all possible
conditions and situations that may occur. It must be
understood that common sense, caution, and care must
be used with any electrical product.
PL-0016
CAUTION!
Is damaged, It shall be exclusIvely replaced by the manufacturer or Its
® product.
servIce agent or a sImIlar qualIfIed person In order to avoId a hazard.
Indoor use only
FCC PArT 15
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that the interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
CAUTION:
recognized by OttLite Technologies voids OttLite's responsibility for
proper function of product
CAN ICES-3 (B)/NMB-3 (B)
AC/DC ADAPTER
Input: AC 100-240V, 50-60Hz
Output: 13.2V DC 280mA with male DC plug
® LED Cone Clip Lamp!
LED Cone Clip Lamp
If the external flexIble cable or cord of thIs lumInaIre
.
Any change or modification to product not expressly
REV093016