Page 1 ® R&S SMW-K60/-K117/-K178 ® Bluetooth Signal Generation User Manual (;ÙÒ32) 1175680302 Version 26...
Page 2 This document describes the following software options: ● R&S ® SMW-K60 Bluetooth EDR (1413.4239.xx) ● ® R&S SMW-K117 Bluetooth 5.x (1414.3336.xx) ● ® R&S SMW-K178 Bluetooth 5.4 + Channel Sounding (1434.8279.xx) This manual describes firmware version FW 5.30.175.xx and later of the R&S ®...
Page 3: Table Of Contents
® Contents R&S SMW-K60/-K117/-K178 Contents 1 Welcome to the Bluetooth options............7 Key features........................7 Accessing the Bluetooth dialog.................. 9 What's new........................9 Documentation overview....................9 1.4.1 Getting started manual....................10 1.4.2 User manuals and help....................10 1.4.3 Tutorials.........................10 1.4.4 Service manual......................10 1.4.5 Instrument security procedures..................11 1.4.6 Printed safety instructions.....................
Page 4 ® Contents R&S SMW-K60/-K117/-K178 2.4.3 Packet structure and fields....................30 2.4.4 Bluetooth modulation schemes..................33 3 Bluetooth general settings..............35 4 Dirty transmitter test settings............. 39 5 Bluetooth LE configuration and settings...........44 Channel settings......................44 Advertising event and frame configuration..............51 5.2.1 Advertising event and frame settings................51 5.2.2 Connection settings.......................54 5.2.3...
Page 5 ® Contents R&S SMW-K60/-K117/-K178 5.5.5 CS IND payload settings..................... 126 5.5.6 CS terminate payload settings..................128 5.5.7 CS FAE payload settings.................... 128 5.5.8 CS channel map payload settings................129 Test packet configuration..................129 6 Bluetooth BR/EDR configuration and settings....... 133 Channel settings....................... 133 Packet configuration....................135 7 Signal control and signal characteristics........
Page 6 ® Contents R&S SMW-K60/-K117/-K178 Packet configuration commands - LE..............211 8.6.1 General configuration....................217 8.6.2 Header configuration....................219 8.6.3 Payload configuration....................222 8.6.4 Cs payload configuration.....................251 Test packet configuration commands - LE............. 269 Channel configuration commands - BR/EDR............272 Packet configuration commands - BR/EDR............273 8.10 Filter/clipping commands..................282 8.11...
Page 7: Welcome To The Bluetooth Options
® Welcome to the Bluetooth options R&S SMW-K60/-K117/-K178 Key features 1 Welcome to the Bluetooth options The Bluetooth options R&S SMW-K60/-K117/-K178 are firmware applications that add functionality to generate signals in accordance with the Bluetooth standard. This user manual contains a description of the functionality that the application pro- vides, including remote control operation.
Page 8 ® Welcome to the Bluetooth options R&S SMW-K60/-K117/-K178 Key features ● Dirty transmitter test, compliant to the RF test specification with options to change start phase, frequency drift rate and frequency drift deviation ● Support of CRC corruption for every 2nd packet ●...
Page 9: Accessing The Bluetooth Dialog
® Welcome to the Bluetooth options R&S SMW-K60/-K117/-K178 Documentation overview 1.2 Accessing the Bluetooth dialog To open the dialog with Bluetooth settings ► In the block diagram of the R&S SMW200A, select "Baseband > Bluetooth". A dialog box opens that displays the provided general settings. The signal generation is not started immediately.
Page 10: Getting Started Manual
® Welcome to the Bluetooth options R&S SMW-K60/-K117/-K178 Documentation overview www.rohde-schwarz.com/manual/smw200a 1.4.1 Getting started manual Introduces the R&S SMW200A and describes how to set up and start working with the product. Includes basic operations, typical measurement examples, and general infor- mation, e.g.
Page 11: Instrument Security Procedures
® Welcome to the Bluetooth options R&S SMW-K60/-K117/-K178 Documentation overview 1.4.5 Instrument security procedures Deals with security issues when working with the R&S SMW200A in secure areas. It is available for download on the internet. 1.4.6 Printed safety instructions Provides safety information in many languages. The printed document is delivered with the product.
Page 12: Videos
® Welcome to the Bluetooth options R&S SMW-K60/-K117/-K178 Notes on screenshots 1.4.11 Videos Find various videos on Rohde & Schwarz products and test and measurement topics on YouTube: https://www.youtube.com/@RohdeundSchwarz On the menu bar, search for your product to find related videos. Figure 1-1: Product search on YouTube 1.5 Scope Tasks (in manual or remote operation) that are also performed in the base unit in the...
Page 13: About The Bluetooth Options
® About the Bluetooth options R&S SMW-K60/-K117/-K178 About Bluetooth LE 2 About the Bluetooth options The R&S SMW200A provides you with the ability to generate signals in accordance with the core specification 5.4 for Bluetooth wireless technology. This section lists required options and provides background information on basic terms and principles used in Bluetooth technology.
Page 14: Packet Formats For Le
® About the Bluetooth options R&S SMW-K60/-K117/-K178 About Bluetooth LE Table 2-1: Operating band Frequency range RF channels k and center frequencies f 2400.0 MHz to 2483.5 MHz k = 0 to 39, f = k * 2 MHz + 2402 MHz Table 2-2: Channel index RF channel RF center frequency...
Page 15 ® About the Bluetooth options R&S SMW-K60/-K117/-K178 About Bluetooth LE Each packet consists of four mandatory fields: Preamble, Access Address, Protocol Data Unit (PDU) and Cyclic Redundancy Check (CRC). For Bluetooth direction finding, the optional field Constant Tone Extension (CTE) is at the end of the packet. See also Chapter 2.2.6, "Direction finding", on page 21.
Page 16: Packet Types For Le
® About the Bluetooth options R&S SMW-K60/-K117/-K178 About Bluetooth LE Table 2-4: Packet format for LE coded PHY Pream- Access TERM1 TERM2 address Number of uncoded bits 16 - 2056 Duration in µs for S=8 coding 128 - 16448 Duration in µs for S=2 coding 32 - 4112 Packets take between 462 μs and 17040 μs to transmit.
Page 17 ® About the Bluetooth options R&S SMW-K60/-K117/-K178 About Bluetooth LE AUX_CHAIN_IND AUX_CONNECT_REQ AUX_SYNC_IND AUX_CONNECT_RSP Data channel packet types The data channel PDU has a 16-bit header, a variable size payload, and can include a message integrity check (MIC) field as shown in "Header"...
Page 18: Advertising Channel Packet Structure
® About the Bluetooth options R&S SMW-K60/-K117/-K178 About Bluetooth LE 2.2.3 Advertising channel packet structure Header Header Payload 2 octets 1-255 octets PDU type ChSel TxAdd RxAdd Length 4 bits 1 bit 1bit 1 bit 1 bit 8 bits ● The possible PDU types, indicated in the header of advertising channel PDU, are listed in the previous tables, see Table...
Page 19 ® About the Bluetooth options R&S SMW-K60/-K117/-K178 About Bluetooth LE Payload The advertising channel PDU types consist of three groups. Table 2-10: Advertising channel PDU types PDU type PDU name Option Advertising PDU (legacy) ADV_IND, ADV_DIRECT_IND, ADV_NONCONN_IND, R&S SMW-K60 ADV_SCAN_IND Advertising PDU (extended) ADV_EXT_IND, AUX_ADV_IND, AUX_SYNC_IND, R&S SMW-K117...
Page 20: Data Channel Packet Structure
® About the Bluetooth options R&S SMW-K60/-K117/-K178 About Bluetooth LE 2.2.4 Data channel packet structure Header Header Payload 2 octets 0-251 octets 4 octets LLID NESN Length 2 bits 1 bit 1 bit 1 bit 3 bits 8 bits The 16-bit header field consists of five fields: ●...
Page 21: Direction Finding
® About the Bluetooth options R&S SMW-K60/-K117/-K178 About Bluetooth LE Option R&S SMW-K60 supports LE uncoded 1 Msymbol/s (LE 1M) physical layer (PHY). Option R&S SMW-K117 supports LE Coded 1 Msymbol/s PHY and an optional modu- lation scheme LE uncoded 2 Msymbol/s (LE 2M) PHY. 2.2.6 Direction finding Since Bluetooth version 5.1, a Bluetooth LE device can transmit its direction informa- tion to a Bluetooth receiver.
Page 22 ® About the Bluetooth options R&S SMW-K60/-K117/-K178 About Bluetooth LE Figure 2-4: Angle of Arrival method Angle of Departure (AoD) method A Bluetooth LE transmitter sends direction finding enabled packets using an antenna array. A receiving Bluetooth LE device, consisting of a single antenna, captures I/Q samples and the geometry of the antenna array from profile-level information.
Page 23 ® About the Bluetooth options R&S SMW-K60/-K117/-K178 About Bluetooth LE Figure 2-5: Angle of Departure method The geometry of the antenna array is information that is shared between Bluetooth LE transmitter and receiver on a profile-level. The antenna switching pattern and the method of angle estimation is specified by Constant Tone Extension.
Page 24 ® About the Bluetooth options R&S SMW-K60/-K117/-K178 About Bluetooth LE CTEInfo field Length Value Description CTETime 5 bit 2 to 20 CTE length = 8 µs * Value Other values are reserved for future use. 1 bit 1 to 2 Reserved for future use CTEType 2 bit...
Page 25: About Bluetooth Le Channel Sounding
® About the Bluetooth options R&S SMW-K60/-K117/-K178 About Bluetooth LE Channel Sounding Figure 2-8: CTE structure for AoD method For more information, refer to section 2.5 Constant Tone Extension and IQ Sampling of core specification for Bluetooth wireless technology, volume 6, part B. 2.3 About Bluetooth LE Channel Sounding This section provides basic information on Bluetooth LE Channel Sounding technology.
Page 26: About Bluetooth Br/Edr
® About the Bluetooth options R&S SMW-K60/-K117/-K178 About Bluetooth BR/EDR A CS procedure exists only for a limited duration, and consists of CS events, CS sube- vents, and CS steps. CS events may contain one or more subevents. CS subevents contain two or more CS steps.
Page 27: Bluetooth Packet Types For Br/Edr
® About the Bluetooth options R&S SMW-K60/-K117/-K178 About Bluetooth BR/EDR Two modulation formats are used for Bluetooth: the mandatory basic rate (BR) and the optional enhanced data rate (EDR). The BR mode uses binary FM modulation and pro- vides a data rate of 1 Mbit/s. The EDR mode uses two types of PSK modulation, the π/4-DQPSK or 8DPSK, and achieves data rates of 2 Mbit/s and 3 Mbit/s, respectively.
Page 28 ® About the Bluetooth options R&S SMW-K60/-K117/-K178 About Bluetooth BR/EDR Table 2-16: ACL packets - enhanced rate Type Payload User Payload Slot number Header (bytes) (bytes) 2-DH1 0-54 2-DH3 0-367 2-DH5 0-679 Yes, 16-bit 3-DH1 0-83 3-DH3 0-552 2-DH5 0-1021 Figure 2-10: Packet structure of ACL packets - enhanced data rate 2.4.1.2 SCO and eSCO packets...
Page 29 ® About the Bluetooth options R&S SMW-K60/-K117/-K178 About Bluetooth BR/EDR Table 2-18: eSCO packets - basic rate Type Payload User Payload Slot number Header (bytes) (bytes) 1-30 n.a. Yes, 16-bit 1-120 1-180 (Data only) Figure 2-13: Packet structure eSCO packets - basic rate Table 2-19: eSCO packets - basic rate Type Payload...
Page 30: Bluetooth Transport Modes
® About the Bluetooth options R&S SMW-K60/-K117/-K178 About Bluetooth BR/EDR Table 2-21: Common link control packets: packet structure Packet Type ID Packet Types NULL and PULL Packet Types FHS 2.4.2 Bluetooth transport modes There are three different transport modes defined in the Bluetooth core specification, each of them with special applications: ●...
Page 31 ® About the Bluetooth options R&S SMW-K60/-K117/-K178 About Bluetooth BR/EDR Table 2-22: The access code fields Field Description Packets Preamble A fixed zero-one pattern of 4 symbols, used to facili- All packets tate DC compensation Sync word A 64-bit code word derived from a 24-bit address, All packets improves timing acquisition Trailer...
Page 32 ® About the Bluetooth options R&S SMW-K60/-K117/-K178 About Bluetooth BR/EDR Synchronous data fields Asynchronous data fields Synchronous and asynchronous data fields The meaning of some payload fields is given in the table below. Table 2-24: The payload fields Field Description The cyclic redundancy error check Guard, sync The guard time and synchronization sequence, used for physical layer change of modula-...
Page 33: Bluetooth Modulation Schemes
® About the Bluetooth options R&S SMW-K60/-K117/-K178 About Bluetooth BR/EDR Table 2-25: The payload fields for the FHS packet Field Description Parity bits Form the first part of the sync word of the access code of the device that sends the FHS packet Contains the lower address part of the device that sends the FHS packet An extended inquiry response, provides miscellaneous information during the inquiry...
Page 34 ® About the Bluetooth options R&S SMW-K60/-K117/-K178 About Bluetooth BR/EDR Table 2-26: The modulation types and corresponding packet types Modulation type Packet types GFSK ID, NULL, POLL, FHS, DM1, DH1, DM3, DH3, DM5, DH5, AUX1, HV1, HV2, HV3, DV, EV3, EV4, EV5 GFSK + π/4-DQPSK 2-DH1, 2-DH3, 2-DH5, 2-EV3, 2-EV5 GFSK + 8DPSK...
Page 35: Bluetooth General Settings
® Bluetooth general settings R&S SMW-K60/-K117/-K178 3 Bluetooth general settings Access: ► Select "Baseband" > "Bluetooth". The tab provides general settings to call default settings and the "Save"/"Recall" settings. Also, it provides Bluetooth version information, Bluetooth mode settings and access to further settings. Settings: State..........................35 Set To...
Page 36: Save/Recall
® Bluetooth general settings R&S SMW-K60/-K117/-K178 Parameter Value State Not affected by "Set To default" Bluetooth version R&S SMW-K60: 4.2 R&S SMW-K117: 5.4 R&S SMW-K178: 5.4 + Channel Sounding Bluetooth mode Basic Rate + EDR Transport mode ACL(Asynchronous)+EDR Packet type Sequence length 1 Frame Slot timing...
Page 37: Bluetooth Version
® Bluetooth general settings R&S SMW-K60/-K117/-K178 Remote command: on page 167 [:SOURce<hw>]:BB:BTOoth:WAVeform:CREate Bluetooth Version Displays the version of the standard that the firmware supports. The displayed version for Bluetooth wireless technology depends on installed options. For example, "Bluetooth Version" > "5.4" requires R&S SMW-K117. Remote command: on page 167 [:SOURce<hw>]:BB:BTOoth:VERSion?
Page 38: Power Ramping
® Bluetooth general settings R&S SMW-K60/-K117/-K178 The button also displays configured filters and the clipping state. Chapter 7.1, "Filter/clipping settings", on page 143. Remote command: on page 284 [:SOURce<hw>]:BB:BTOoth:FILTer:FILTers? on page 283 [:SOURce<hw>]:BB:BTOoth:CLIPping:STATe Power Ramping Opens a dialog to configure the power ramping. Chapter 7.2, "Power ramping settings", on page 149.
Page 39: Dirty Transmitter Test Settings
® Dirty transmitter test settings R&S SMW-K60/-K117/-K178 4 Dirty transmitter test settings Access: 1. Select "Bluetooth" > "General". 2. Select "Dirty Transmitter Test". The dialog provides settings to configure dirty transmitter test settings. These set- tings contain parameters that you can change for the central device signal. It is used to test the connection under 'dirty transmitter' conditions, and to define the influence on the receiver quality (bit error rate tests).
Page 40 ® Dirty transmitter test settings R&S SMW-K60/-K117/-K178 Table 4-2: Dirty transmitter test parameters for EDR Δt /ppm offset error Table 4-3: Dirty transmitter test parameters for LE Δt /ppm offset error standard stable 0.45 0.495 0.48 0.498 0.46 0.496 0.52 0.502 0.53 0.503...
Page 41 ® Dirty transmitter test settings R&S SMW-K60/-K117/-K178 Dirty Transmitter Test Enables the dirty transmitter test. The setting is available for the following packet types: ● BR: DH1, DH3, DH5 For basic rate packets, each enabled set of parameters in the "Dirty Transmitter Setting"...
Page 42 ® Dirty transmitter test settings R&S SMW-K60/-K117/-K178 A sine wave is used to drift the modulated Bluetooth signal around center frequency + carrier frequency offset. The maximum deviation reached during the drift equals the set frequency drift deviation. Remote command: on page 169 [:SOURce<hw>]:BB:BTOoth:DTTest:FDDeviation Number Of Packets Per Set/Number Of Steps Per Set...
Page 43 ® Dirty transmitter test settings R&S SMW-K60/-K117/-K178 Symbol Timing Error (ppm) ← Dirty Transmitter Setting Sets the symbol timing error in ppm. The symbol timing error modifies the symbol clock frequency by the specified value. Remote command: [:SOURce<hw>]:BB:BTOoth:DTTest:TABLe:LONG:SET<ch>:STERror on page 173 [:SOURce<hw>]:BB:BTOoth:DTTest:TABLe:SHORt:SET<ch>:STERror on page 174 Modulation Index ←...
Page 44: Bluetooth Le Configuration And Settings
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Channel settings 5 Bluetooth LE configuration and settings Access: 1. Select "Baseband" > "Bluetooth". 2. Select "Bluetooth Mode" > "Bluetooth Low Energy". The remote commands required to define these settings are described in Chapter 8, "Remote control commands",...
Page 45 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Channel settings The tab provides settings to configure channel settings and general packet set- tings. To display Bluetooth LE event or frame sequences Depending on the channel type packet type and packet format, the "Channel" tab dis- plays a chart at the bottom that illustrates sequences of the corresponding events or frames.
Page 46 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Channel settings Settings: Channel Type........................ 46 Packet Type........................46 Packet Format.......................48 Duty Cycle........................48 Sequence Length......................48 Bluetooth Controller Role....................48 Bluetooth Controller State..................... 49 Corrupted CRC Every 2nd Packet................49 Payload Type........................ 49 Duration.........................49 Modulation Format......................
Page 47 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Channel settings Channel type Packet/PDU type Option Advertising TEST PACKET R&S SMW-K60 Advertising CONTINUOUS R&S SMW-K60 Data DATA R&S SMW-K60 Data CONTROL_DATA, see Table 5-2. Table 5-2. Data TEST PACKET R&S SMW-K60 Data CONTINUOUS R&S SMW-K60...
Page 48 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Channel settings How to: "To display Bluetooth LE event or frame sequences" on page 45 For more information, refer to the specifications document. Remote command: on page 177 [:SOURce<hw>]:BB:BTOoth:UPTYpe Packet Format Selects the packet format that is the format according to the physical layer (PHY) that supports the packet type or PDU type.
Page 49 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Channel settings Bluetooth controller Channel type PDU type role Advertiser (read-only) Advertising ADV_IND, ADV_DIRECT_IND, ADV_NON- CONN_IND, ADV_SCAN_IND, SCAN_RSP, ADV_EXT_IND, AUX_ADV_IND, AUX_CHAIN_IND, AUX_SYNC_IND, AUX_SCAN_RSP, AUX_CON- NECT_RSP, TEST PACKET Scanner (read-only) Advertising SCAN_REQ, AUX_SCAN_REQ Initiator (read-only) Advertising CONNECT_IND, AUX_CONNECT_IND...
Page 50 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Channel settings Specifies the physical layer. Remote command: on page 179 [:SOURce<hw>]:BB:BTOoth:MFORmat Event Configuration/Frame Configuration Opens the "Event Configuration" dialog, if the sequence length of the packet type is expressed in events or opens the "Frame Configuration" dialog, if it is expressed in frames, see Chapter 5.2, "Advertising event and frame configuration",...
Page 51: Advertising Event And Frame Configuration
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising event and frame configuration Sets the role of the Channel Sounding device. "Initiator" Channel Sounding device initiates a CS procedure. "Reflector" Channel Sounding device responds to a CS procedure. Remote command: on page 192 [:SOURce<hw>]:BB:BTOoth:CS:ROLE 5.2 Advertising event and frame configuration...
Page 52 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising event and frame configuration 2. Select "Event Configuration" for event-type packets or "Frame Configuration" for frame-type packets. Figure 5-1: Event configuration for an advertising channel (advertiser) Figure 5-2: Frame configuration for an advertising channel (scanner) The "Advertising Settings"...
Page 53 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising event and frame configuration Sets the time interval between two consecutive advertising events, regarding the start- ing points. Remote command: For packet type ADV_DIRECT_IND and duty cycle high: on page 183 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:ADINterval For all others: on page 183...
Page 54: Connection Settings
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising event and frame configuration Transmit Window Offset Requires packet type CONNECT_IND, AUX_CONNECT_REQ or AUX_CON- NECT_RSP. Displays the start point of the transmit window. For related settings, see "Transmit Win- dow Offset" on page 77.
Page 55 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising event and frame configuration Settings: No. Of Tx Packets/Event....................55 Connection Event Interval..................... 55 LL Connection Mode..................... 55 Long Term Key(hex)......................56 Selected Data Channel Index..................56 No. Of Tx Packets/Event Sets the number of TX packets per event. Each connection contains at least one data channel packet.
Page 56: Channel Table Settings
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising event and frame configuration "Un-encrypted" Payload data is transmitted without encoding. Example of packet type data: "Encrypted" The link layer connection runs in encrypted mode. Example of packet type data: Remote command: on page 184 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:LCMode Long Term Key(hex)
Page 57 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising event and frame configuration 2. Select "Channel Table" The channel table displays all possible channels and their characteristics. Also you can select the channel that you want to use for the generated packets. Settings: Channel Table The channel table displays channel characteristics including the channel state.
Page 58: Advertising And Data Packet Configuration
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration 5.3 Advertising and data packet configuration Access: 1. Select "Bluetooth" > "General". 2. "Bluetooth Mode" > "Bluetooth LE". 3. In the "Channel" tab, select the channel type, for example, "Channel Type" > "Advertising".
Page 59 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration Settings: Data Whitening......................59 Access Address......................59 CRC Initial Value(hex)....................60 Data Whitening Enables data whitening. Evenly distributed white noise is ideal for the transmission and real data can be forced to look similar to white noise with different methods called "Data Whitening".
Page 60: Header Settings
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:AADDress on page 218 CRC Initial Value(hex) Requires data channel PDU or an advertising channel PDU. For an advertising chan- nel, also requires packet type CONNECT_IND or AUX_CONNECT_REQ. Sets the initialization value for the 24-bit cyclic redundancy check (CRC) calculation.
Page 61 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration SN Start Value Requires a data channel packet that is not a test packet. Sets the sequence number of the packet. You can set this parameter for the first event. From the second event and later events, the field is empty.
Page 62: Cteinfo Settings
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration "Public" Allocates a unique 48-bit address to each Bluetooth LE device. Public addresses use an organizational unique identifier (OUI) obtained from the IEEE registration authority. "Random" Allocates a 48-bit random static device address to each Bluetooth LE device.
Page 63: Legacy Advertising Pdu Payload Settings
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CTIMe on page 220 CTEType Sets the type of constant tone extension. The type specifies the CTE AoA/AoD method and for AoD the length of the switching and I/Q sampling slots. Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CTYPe on page 221...
Page 64 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration For an overview of supported legacy advertising PDUs, see Table 2-10. Settings: Advertiser's Device Addr....................64 Target's Device Addr..................... 65 Data Source........................65 Data Length........................65 Advertiser's Device Addr Sets the 48-bit device address of the advertiser.
Page 65 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ANUap on page 227 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ALAP on page 226 Target's Device Addr TargetA field of the device address that is a scanner's device address or an initiator's device address. Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:TNUap on page 227...
Page 66: Extended Advertising Pdu Payload Settings
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:DLENgth on page 232 5.3.5 Extended advertising PDU payload settings Option: R&S SMW-K117 Access: 1. Select an extended advertising PDU: a) In the "Channel" tab, select "Channel Type" > "Advertising". b) Select an extended advertising PDU, for example "Packet Type"...
Page 67 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration The tab provides general settings to configure the payload of the extended adver- tising PDUs. Advertising Mode......................67 Extended Header......................67 Data Source........................67 Data Length........................67 Advertising Mode Selects the mode of the advertisement in the AdvMode field.
Page 68: Settings: Adva
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration If enabled, the R&S SMW200A signals the extended header for extended advertis- ing PDUs. The "Extended Header" table provides general settings to configure the extended header. It also provides access to further settings of fields within the extended header.
Page 69: Advdatainfo
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration Selecting "Conf" opens the CTEInfo configuration dialog to define the CTE length and the CTE method for direction finding. See Chapter 5.3.3, "CTEInfo settings", on page 62. Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:EHFLags: on page 235...
Page 70: Acad Length
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration ACAD Length Specifies the length of an additional controller advertising data (ACAD) field. Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ALENgth on page 227 ACAD Sets the pattern for additional controller advertising data (ACAD). The following standard data sources are available: ●...
Page 71 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration 5.3.5.3 AdvDataInfo configuration settings Access: 1. Select "Payload" > "Extended Header". 2. Select "AdvDataInfo" > "On". 3. Select "AdvDataInfo" > "Conf". The "AdvDataInfo Configuration" section opens. The section provides AdvDataInfo field settings and displays the structure of the field graphically.
Page 72 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration The "AuxPtr Configuration" dialog opens. The "AuxPtr Configuration" tab provides AuxPtr field settings and displays the structure of the field graphically. The "Secondary Advertising Channel Table" tab lists the configuration of all 37 LE channels and allows you to enable the channel that you want to use for secondary advertising.
Page 73 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:APHY on page 228 5.3.5.5 SyncInfo configuration settings Access: 1. Select "Payload" > "Extended Header". 2. Select "SyncInfo" > "On". 3. Select "SyncInfo" > "Conf". The "SyncInfo Configuration"...
Page 74: Scanning Pdu Payload Settings
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SPOFfset on page 246 Offset Units Sets the offset units of the sync packet offset, see "Sync Packet Offset" on page 73. Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SOUNits on page 245 Offset Adjust Adjusts the "Sync Packet Offset"...
Page 75 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration 2. Select "Event Configuration"/"Frame Configuration" > "Packet Configuration". 3. Select "Payload". The tab provides settings to configure the payload of the scanning PDUs. For an overview of supported scanning PDUs, see Table 2-10.
Page 76: Initiating Pdu Payload Settings
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration Extended Header Requires an AUX_SCAN_RSP PDU. For related settings, see "Extended Header" on page 67 and Chapter 5.3.5.2, "Exten- ded header settings", on page 67. 5.3.7 Initiating PDU payload settings Access: 1.
Page 77 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration Data Source........................79 Data Length........................79 Extended Header......................79 Initiator's Device Addr Sets the 48-bit device address of the initiator. For more information, see "Advertiser's Device Addr" on page 64. Remote command: Company_Assigned and Company_Id in the device address of an initiator: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ICASsigned...
Page 78 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration Remote command: For advertising channels: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:WOFFset on page 247 For data channels: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:NWOFfset on page 241 Connection Event Interval Requires packet type CONNECT_IND, AUX_CONNECT_REQ, LL_CONNEC- TION_UPDATE_IND, LL_CONNECTION_PARAM_REQ or LL_CONNEC- TION_PARAM_REQ.
Page 79: Data Channel Pdu Payload Settings
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration Show Data Channel Map Table/Hide Data Channel Map Table Requires packet type CONNECT_IND or LL_CHANNEL_MAP_IND. Shows or hides the data channel map table. For related settings, see Chapter 5.2.3, "Channel table settings",...
Page 80 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration 2. Select "Event Configuration" for event-type packets or "Frame Configuration" for frame-type packets. The "Event Configuration" or "Frame Configuration" dialog opens. 3. Select "Packet Configuration" The dialog provides settings to configure the payload of advertising PDUs. For an overview of supported advertising PDUs, see Table 2-10.
Page 81 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration Min Used Channels.......................87 ID(hex).......................... 87 SyncInfo Configuration....................87 Connection Event Count....................87 Last Pa Event Counter....................88 SID(hex)........................88 Address Type........................ 88 Sleep Clock Accuracy....................88 PHY..........................88 Advertiser's Device Addr....................
Page 82 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration Connection Instant Requires packet type LL_CONNECTION_UPDATE_IND, LL_CHANNEL_MAP_IND or LL_PHY_UPDATE_IND. The PDU LL_PHY_UPDATE_IND also requires option R&S SMW-K117. Sets a connection instant for indicating the connection event at which the new connec- tion parameters are taken in use.
Page 83 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration: on page 233 EDIVersifier Session Key iD(hex) Requires the packet type LL_ENC_REQ and a Central Bluetooth controller or LL_ENC_RSP and a Peripheral Bluetooth controller. Sets the portion of the Central or the portion of the Peripheral of the session key diver- sifier (SKDm/SKDs).
Page 84 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration Sets the version of the Bluetooth controller. It is an 8-bit value in hexadecimal repre- sentation. Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:VNUMber on page 247 SubVersion Number(hex) Requires packet type LL_VERSION_IND. Sets a unique 16-bit value for each implementation or revision of an implementation of the Bluetooth controller.
Page 85 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration Ref. Connection Event Count Requires option R&S SMW-K117 and packet types LL_CONNECTION_PARAM_REQ or LL_CONNECTION_PARAM_RSP. Sets connection event counter relative to the calculation of all valid offset fields Offset0 to Offset5.
Page 86 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MROCtets on page 238 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MTOCtets on page 238 MaxRxTime/MaxTxTime Requires option R&S SMW-K117 and packet types LL_LENGTH_REQ or LL_LENGTH_RSP. Sets the maximum allowed time to receive (RX) a packet or to transmit (TX) a packet. Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MRTime on page 239...
Page 87 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:STMPhy: on page 239 L1M:STATe [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:STMPhy: on page 239 L2M:STATe [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:STMPhy: on page 239 LCOD:STATe PHYs Requires option R&S SMW-K117 and packet type LL_MIN_USED_CHANNELS_IND. Sets the physical layers for which the Peripheral device has a minimum used channels requirement.
Page 88 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CECount on page 248 Last Pa Event Counter Requires option R&S SMW-K117 and packet type LL_PERIODIC_SYNC_IND. Sets the lastPaEventCounter field in the CtrData field. The lastPaEventCounter value is typically equal to the PaEventCounter value in the AUX_SYNC_IND PDU.
Page 89: Featureset Configuration Settings
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:PHY:L1M: on page 250 STATe [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:PHY:L2M: on page 250 STATe [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:PHY:LCOD: on page 250 STATe Advertiser's Device Addr Requires option R&S SMW-K117 and packet type LL_PERIODIC_SYNC_IND. For related settings, see "Advertiser's Device Addr"...
Page 90 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Advertising and data packet configuration a) Select "Bluetooth Controller Role" > "Central". b) Select "Packet Type" > "LL_FEATURE_REQ" or "LL_PERIPHERAL_FEA- TURE_REQ". 4. For a peripheral controller, proceed as follows: a) Select "Bluetooth Controller Role" > "Peripheral". b) Select "Packet Type"...
Page 91: Cs Subevent Configuration
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS subevent configuration Link layer feature Link layer feature LE extended advertising Sleep clock accuracy updates LE periodic advertising Remote public key validation Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration: on page 236 FSBit<ch0>:STATe 5.4 CS subevent configuration Option: R&S SMW-K178 Access: 1.
Page 92 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS subevent configuration 2. Select "Subevent Settings". The tab provides settings to configure subevent settings. Settings: Subevent Length......................92 Subevent Interval......................92 Step Scheduling......................93 Number of Subevents....................93 Subevent table......................93 Subevent........................
Page 93 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS subevent configuration Step Scheduling Sets the CS step scheduling mode. "Auto" Automatic CS step scheduling. The subevent length, the subevent interval and the number of subevents are configurable. The number of CS steps is 2. "Manual"...
Page 94 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS subevent configuration Subevent Displays the subevent number "Subevent x" within a subevent interval. "x" ranges from 0 to 31 depending on the number of subevents, see "Number of Subevents" on page 93. Remote command: Via suffix SUBevent<ch>...
Page 95: Channel Table
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS subevent configuration 5.4.2 Channel table Access: 1. Select "CS Subevent Configuration". 2. Select "Channel Table". The tab lists general settings for all 78 Bluetooth LE channels in a table. Settings: Channel.........................95 Center Frequency (MHz)....................95 Channel...
Page 96: Cs Security Settings
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS subevent configuration Channel Index Displays the channel index of the channel. See also Table 2-13. Remote command: [:SOURce<hw>]:BB:BTOoth:CS:CTABle[:CHANnel<ch0>]:CINDex? on page 206 Channel Type Displays the channel type that is Channel Sounding for all channels. Remote command: [:SOURce<hw>]:BB:BTOoth:CS:CTABle[:CHANnel<ch0>]:CTYPe? on page 206...
Page 97 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS subevent configuration Settings: CS_IV_C(hex)....................... 97 CS_IV_P(hex)....................... 97 CS_IN_C(hex).......................97 CS_IN_P(hex)....................... 97 CS_PV_C(hex)......................97 CS_PV_P(hex)......................97 CS_IV_C(hex) Requires packet type CS SEQUENCE or LL_CS_SEC_REQ. Sets the CS_IV_C parameter. The parameter is 64-bit in hexadecimal representation. Remote command: on page 207 [:SOURce<hw>]:BB:BTOoth:CS:CIVC...
Page 98: Channel Selection Settings
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS subevent configuration 5.4.4 Channel selection settings Access: 1. Select "CS Subevent Configuration". 2. Select "Channel Selection". The tab provides settings to configure channel selection. Settings: CSFilteredChM(hex)..................... 98 ChM_Repetition......................98 ChSel..........................98 Ch3cShape........................
Page 99: Cs Step Configuration
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS subevent configuration "Algorithm #3c" Sets for Algorithm #3c channel selection algorithm. Table 5-7: Algorithm #3c parameters CSChannelJump seq1StartCh seq2StartCh maxRepsAllowed saltRate Remote command: on page 210 [:SOURce<hw>]:BB:BTOoth:CS:CSEL Ch3cShape Requires "ChSel" > "Algorithm #3c". Sets the bits of the Ch3cShape field.
Page 100 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS subevent configuration The "CS Step Config" tab of the "Structure for Subevent x" dialog opens. The tab provides CS step settings for the first subevent "Subevent 0". If configured, all following subevents share CS step configuration as subevent 0. Settings: ●...
Page 101 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS subevent configuration Table 5-8: CS step main modes and submodes "Main_Mode" "Sub_Mode" "Mode-1" "None" "Mode-2" "None", "Mode-1", "Mode-3" "Mode-3" "None", "Mode-2" Remote command: on page 196 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:MMODe Sub_Mode Sets the submode of the main mode. The table Table 5-8 provides an overview on available submodes per main mode.
Page 102 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS subevent configuration 5.4.5.2 Mode-0 config settings Access: ► Select "CS Step Config" > "Mode-0 Config". The tab provides Mode-0 CS step settings. Settings: T_IP1 Sets the time "T_IP1" for Mode-0 CS steps. Remote command: on page 198 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:MZERo:TIPO...
Page 103 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS subevent configuration ● Select "Main_Mode" > "Mode-2" and "Sub_Mode" > "Mode-1". The tab provides Mode-1 CS step settings. Settings: T_IP1...........................103 Sequence Length......................103 Sequence Type......................103 User Payload Pattern....................104 Select Data List......................
Page 104 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS subevent configuration User Payload Pattern Displaying the parameter "User Payload Pattern" requires the following: ● "Packet Type" > "TEST PACKET". ● "Main_Mode" > "Mode-1" or "Mode-3". "Sub_Mode" > "Mode-1" or "Mode-3". ●...
Page 105 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS subevent configuration ● Select "Main_Mode" > "Mode-3" and "Sub_Mode" > "Mode-2". The tab provides Mode-2 CS step settings. Settings: T_SW.......................... 105 N_AP...........................105 T_PM...........................105 T_IP2...........................105 T_SW Sets the time "T_SW" for Mode-2. Remote command: on page 199 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:MTWO:TSW?
Page 106 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS subevent configuration 5.4.5.5 Mode-3 config settings Access: 1. Select "CS Step Config" > "General". 2. Select Mode-3 in the CS step main mode or submode: ● Select "Main_Mode" > "Mode-3". ● Select "Main_Mode"...
Page 107 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS subevent configuration T_PM Sets the time "T_PM" for Mode-3. Remote command: on page 199 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:MTHRee:TPM T_IP2 Sets the time "T_IP2" for Mode-3. Remote command: on page 200 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:MTHRee:TIPT Sequence Length Sets the sequence length. The length is discrete and depends on the sequence type. Sequence type Sequence length Sounding sequence...
Page 108: Cs Step Info
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS subevent configuration "Use CS_SYNC_User_Payload" Selects binary data from a user-defined data list file, see "Select Data List" on page 104. Remote command: on page 201 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:UPPattern Select Data List Requires "User Payload Pattern" > "Use CS_SYNC_User_Payload". "Data Source"...
Page 109 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS subevent configuration Settings: Step..........................109 Mode Type........................109 Channel Index......................110 CS Access Address.....................110 Sounding Sequence Content/Random Sequence Content......... 110 Companion Signal....................... 110 CS Tone Ext.........................112 Step Displays the number of the CS step "Step x". "x" depends on the number of main mode steps, see "Main_Mode_Steps"...
Page 110 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS subevent configuration Channel Index Sets or displays the channel index for individual CS steps. Setting the index requires "Step Scheduling" > "Manual" See also Table 2-13. Remote command: [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>][:STEP<st0>]:CINDex on page 203 CS Access Address Sets or displays the 32-bit CS access address for individual CS steps.
Page 111 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS subevent configuration "Companion Signal" Enables or disables the companion signal. This signal consists of one or two signals that deviate symmetrically from the carrier frequency of the wanted signal. The carrier frequency is the center frequency of the channel that relates to the channel index, see "Channel Index"...
Page 112: Cs Control Data Payload Settings
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS control data payload settings Requires "Companion Signal" ≠ "None". "Data Source" Selects the data source. The following standard data sources are available: ● "All 0"/"All 1" An internally generated sequence containing 0 data or 1 data. ●...
Page 113: Cs Security Payload Settings
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS control data payload settings Access: 1. Select "Packet Configuration". 2. Select "Payload". The tab provides settings to configure the packet/PDU payload. ● CS security payload settings................. 113 ● CS capabilities payload settings................113 ●...
Page 114 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS control data payload settings Settings: ● CpbData 1 settings....................114 ● CpbData 2 settings....................116 ● CpbData 3 settings....................117 5.5.2.1 CpbData 1 settings Mode_Types........................114 RTT_Capability......................114 RTT_AA_Only......................114 RTT_Sounding_N......................115 RTT_Random_Sequence_N..................115 NADM_Sounding_Capability..................115 NADM_Random_Sequence_Capability..............115 CS_SYNC_PHY_Capability..................
Page 115 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS control data payload settings RTT_Sounding_N Displays or sets the time values of the RTT_Sounding_N field. Setting the value depends on the bits of the RTT_Capability field. See the table Table 5-9 for an overview.
Page 116 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS control data payload settings Role "Role" on page 50. Companion_Signal Enables the companion signal. See also "Companion Signal" on page 110. Remote command: on page 257 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:CSIGnal 5.5.2.2 CpbData 2 settings No_FAE........................
Page 117 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS control data payload settings Sets the bits that are reserved for future use (RFU). The number of RFU bits can vary depending on the CS_Control_Data PDU. Remote command: on page 264 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:RFU Num_Configs Sets the Num_Configs field that relates to the number of independent CS configura-...
Page 118 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS control data payload settings "T_IP1" Displays the T_IP1 time of the bit position. "T_IP1 Capability" Enables the T_IP1 capability per bit position. Remote command: [:SOURce<hw>]:BB:BTOoth:CS:CDATa[:BPOSition<ch0>]:TIPO: on page 254 CAPability Show T_IP2 Capability Table/Hide T_IP2 Capability Table Shows or hides the "T_IP2_Capability Table".
Page 119: Cs Configuration Payload Settings
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS control data payload settings T_PM_Capability Table The table provides settings to enable the T_PM capability including the T_PM time per bit position. You can enable T_PM capabilities for bit position 0 to bit position 2. "Bit Position"...
Page 120 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS control data payload settings ChM_Repetition Sets the 3-bit ChM_Repetition field. The value equals the number of cycles of the ChM field for non-Mode-0 CS steps within a CS procedure. Remote command: on page 210 [:SOURce<hw>]:BB:BTOoth:CS:CMRepetition Main_Mode...
Page 121 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS control data payload settings This value indicates the TX PHY of the remote device, to which the Pwr_Delta field in this PDU applies. See also "Packet Format" on page 48. Remote command: on page 263 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:PHY? RTT_Type...
Page 122: Cs Payload Settings
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS control data payload settings Sets the bits that are reserved for future use (RFU). The number of RFU bits can vary depending on the CS_Control_Data PDU. Remote command: on page 264 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:RFU ChSel "ChSel"...
Page 123 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS control data payload settings Settings: Config_ID........................123 RFU..........................123 connEventCount......................123 Offset_Min........................123 Offset_Max........................124 Max_Procedure_Len....................124 Event_Interval......................124 Subevent_Per_Event....................124 Subevent_Interval....................... 124 Subevent_Len......................125 Procedure_Interval......................125 Procedure_Count......................125 ACI..........................125 PHY..........................125 Preferred_Peer_Ant....................125 Pwr_Delta........................126 Config_ID Sets the 6-bit Config_ID field that is the CS configuration ID. Settable ID values are 2 bits in decimal representation.
Page 124 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS control data payload settings The Offset_Min time value is greater than or equal to 500 μs and less than 4 s. Remote command: on page 262 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:OMIN Offset_Max Sets the time value of the Offset_Max field. The value has a length of 3 octets or 9 bits. The field corresponds to the proposed maximum time between the ACL anchor point and the offset of the first CS step of the first CS subevent.
Page 125 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS control data payload settings Subevent_Len Sets the subevent length in the Subevent_Len field. The value has a length of 3 octets or 9 bits. The Subevent_Len field implies the maximum duration of each CS subevent in micro- seconds.
Page 126: Cs Ind Payload Settings
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS control data payload settings Table 5-11: Preferred_Peer_Ant field values Bit number Description <PrePeerAnt> Use the first ordered antenna element ANT0 Use the second ordered antenna element ANT1 Use the third ordered antenna element ANT2 Use the fourth ordered antenna element ANT3...
Page 127 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS control data payload settings Remote command: on page 256 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:CID Sets the bits that are reserved for future use (RFU). The number of RFU bits can vary depending on the CS_Control_Data PDU. Remote command: on page 264 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:RFU...
Page 128: Cs Terminate Payload Settings
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 CS control data payload settings Remote command: on page 256 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:ACI Displays the LE physical layer that is the LE uncoded PHY LE1M. See also "Packet Format" on page 48. Remote command: on page 177 [:SOURce<hw>]:BB:BTOoth:PFORmat Pwr_Delta...
Page 129: Cs Channel Map Payload Settings
® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Test packet configuration Settings: Show Channel FAE Table/Hide Channel FAE Table........... 129 Channel FAE Table..................... 129 Show Channel FAE Table/Hide Channel FAE Table Shows or hides the fractional frequency offset actuation error (FAE) channel table. "Channel FAE Table"...
Page 130 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Test packet configuration 3. Select "Channel" > "Packet Type" > "TEST PACKET". 4. Select "Test Packet Configuration". The dialog provides settings to configure test packets. The graphic below the set- tings shows the test packet structure and fields. Settings: Packet Configuration....................130...
Page 131 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Test packet configuration Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SPBit on page 269 Header The "Header" section provides settings to configure the header of the test packet. CTEInfo Present Requires a data channel packet or a test packet. Enables the CTEInfo field in the header of Bluetooth LE data packets in the LE unco- ded PHY.
Page 132 ® Bluetooth LE configuration and settings R&S SMW-K60/-K117/-K178 Test packet configuration Predefined pattern 11110000, 10101010, 11111111, 00000000, 00001111 or 01010101 "Data List" "Data Source" on page 65. Remote command: [:SOURce<hw>]:BB:BTOoth:DTTest:TPConfiguration:UPSource on page 271 Payload Length Sets the payload length of the test packet. Remote command: [:SOURce<hw>]:BB:BTOoth:DTTest:TPConfiguration:UPLength on page 271...
Page 133: Bluetooth Br/Edr Configuration And Settings
® Bluetooth BR/EDR configuration and settings R&S SMW-K60/-K117/-K178 Channel settings 6 Bluetooth BR/EDR configuration and set- tings Access: 1. Select "Baseband" > "Bluetooth". 2. Select "Bluetooth Mode" > "Basic Rate + EDR". The remote commands required to define these settings are described in Chapter 8, "Remote control commands",...
Page 134 ® Bluetooth BR/EDR configuration and settings R&S SMW-K60/-K117/-K178 Channel settings For Bluetooth LE channel settings, see Chapter 5.1, "Channel settings", on page 44. Settings: Packet Type........................ 134 Sequence Length......................134 Slot Timing........................134 Packet Configuration....................135 Packet Type Selects the packet type. The available packets depend on the selected Transport Mode.
Page 135: Packet Configuration
® Bluetooth BR/EDR configuration and settings R&S SMW-K60/-K117/-K178 Packet configuration Packet Configuration Access the "Packet Configuration" dialog, see Chapter 6.2, "Packet configuration", on page 135. The current data source for the packet and the data whitening state are displayed next to the button.
Page 136 ® Bluetooth BR/EDR configuration and settings R&S SMW-K60/-K117/-K178 Packet configuration └ Acknowledgment...................138 └ SEQN Start Value..................138 Payload........................138 └ Data Source....................138 └ Data Length....................139 └ EIR packet follows..................139 └ Flow Control....................139 └ Scan Repetition Mode...................140 └ Class of Device.....................
Page 137 ® Bluetooth BR/EDR configuration and settings R&S SMW-K60/-K117/-K178 Packet configuration Sets the 24-bit lower address part (LAP) in the 64-bit sync word separately, if "Syn- chronize LAP with BD_ADDR > OFF". The LAP is obtained automatically from the Bluetooth device address "BD_ADDR > LAP", if "Synchronize LAP with BD_ADDR >...
Page 138 ® Bluetooth BR/EDR configuration and settings R&S SMW-K60/-K117/-K178 Packet configuration Sets the FLOW bit in the header. This bit indicates the start or stop of transmission of packets over the ACL logical transport. "Go" Allows the other devices to transmit new data. "Stop"...
Page 139 ® Bluetooth BR/EDR configuration and settings R&S SMW-K60/-K117/-K178 Packet configuration ● "PNxx" An internally generated pseudo-random noise sequence. ● "Pattern" An internally generated sequence according to a bit pattern. Use the "Pattern" box to set the bit pattern. ● "Data List"/"Select Data List" Binary data from a list file, internally or externally generated.
Page 140 ® Bluetooth BR/EDR configuration and settings R&S SMW-K60/-K117/-K178 Packet configuration Remote command: on page 280 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:PFControl Scan Repetition Mode ← Payload Available for FHS packets. The 2-bit scan repetition field indicates the interval between two consecutive page scan windows, determines the behavior of the paging device. "R0"...
Page 141 ® Bluetooth BR/EDR configuration and settings R&S SMW-K60/-K117/-K178 Packet configuration Use the "Pattern" box to set the bit pattern. ● "Data List"/"Select Data List" Binary data from a list file, internally or externally generated. Select "Select Data List" to open the standard "Select List" dialog. The dialog lists file with file extension *.dm_iqd if existing.
Page 142 ® Bluetooth BR/EDR configuration and settings R&S SMW-K60/-K117/-K178 Packet configuration Data Length ← DV Payload (Available for all packet types except ID, POLL, NULL and FHS packets) Enters the payload data length in bytes. Remote command: on page 277 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:DLENgth Flow Control ←...
Page 143: Signal Control And Signal Characteristics
® Signal control and signal characteristics R&S SMW-K60/-K117/-K178 Filter/clipping settings 7 Signal control and signal characteristics This section lists settings provided for configuring the baseband filter and configuring power ramping of bluetooth bursts. Also settings are listed for defining the signal gen- eration start and for generating signals necessary for synchronization with other instru- ments.
Page 144: Common Filter Settings
® Signal control and signal characteristics R&S SMW-K60/-K117/-K178 Filter/clipping settings Settings: 7.1.1 Common filter settings....................144 7.1.2 DPSK filter settings..................... 145 7.1.3 Modulation settings..................... 146 7.1.4 Clipping settings......................148 7.1.1 Common filter settings Access: 1. Select "General" > "Filter"/"Clipping". 2. Select "Filter" > "GFSK section". The section provides settings to configure the common baseband GFSK filter.
Page 145: Dpsk Filter Settings
® Signal control and signal characteristics R&S SMW-K60/-K117/-K178 Filter/clipping settings on page 287 [:SOURce<hw>]:BB:BTOoth:FILTer:PARameter:GAUSs on page 288 [:SOURce<hw>]:BB:BTOoth:FILTer:PARameter:LPASs on page 288 [:SOURce<hw>]:BB:BTOoth:FILTer:PARameter:PGAuss on page 288 [:SOURce<hw>]:BB:BTOoth:FILTer:PARameter:RCOSine on page 289 [:SOURce<hw>]:BB:BTOoth:FILTer:PARameter:SPHase Impulse Length Displays the number of filter tabs. If enabled, the most sensible parameter values are selected. The value depends on the coherence check.
Page 146: Modulation Settings
® Signal control and signal characteristics R&S SMW-K60/-K117/-K178 Filter/clipping settings Table 7-1: DPSK filter for Bluetooth EDR packets Transport mode Packet type DPSK filter type ACL+EDR 2-DH1, 2-DH3, 2-DH5 π/4 DQPSK 3-DH1, 3-DH3, 3-DH5 8DPSK eSCO+EDR 2-EV3, 2-EV5 π/4 DQPSK 3-EV3, 3-EV5 8DPSK Settings:...
Page 147 ® Signal control and signal characteristics R&S SMW-K60/-K117/-K178 Filter/clipping settings 2. Select "Modulation Settings". The tab provides settings to configure modulation settings. Settings: Modulation Type......................147 Frequency Deviation....................147 Modulation Index......................147 Symbol Rate Variation....................148 Modulation Type Displays the modulation format used for the current packet selection. Remote command: on page 286 [:SOURce<hw>]:BB:BTOoth:FILTer:MTYPe...
Page 148: Clipping Settings
® Signal control and signal characteristics R&S SMW-K60/-K117/-K178 Filter/clipping settings Symbol Rate Variation Enter the symbol rate. Remote command: on page 289 [:SOURce<hw>]:BB:BTOoth:SRATe:VARiation 7.1.4 Clipping settings Access: 1. Select "General" > "Filter"/"Clipping". 2. Select "Clipping". The tab provides settings to configure clipping. Settings: State..........................148 Clipping...
Page 149: Power Ramping Settings
® Signal control and signal characteristics R&S SMW-K60/-K117/-K178 Power ramping settings Clipping Mode Selects the clipping method. The dialog displays a graphical illustration on how this two methods work. ● "Vector | i + jq |" The limit is related to the amplitude | i + q |. The I and Q components are mapped together, the angle is retained.
Page 150 ® Signal control and signal characteristics R&S SMW-K60/-K117/-K178 Power ramping settings Settings: Ramp Function......................150 Ramp Time........................150 Rise Offset........................150 Fall Offset........................150 Ramp Function Selects the form of the transmitted power, i.e. the shape of the rising and falling edges during power ramp control. The transmitted power rises and falls with linear fashion.
Page 151: Trigger Settings
® Signal control and signal characteristics R&S SMW-K60/-K117/-K178 Trigger settings 7.3 Trigger settings Access: ► Select "Baseband" > "Bluetooth" > "Trigger In". This tab provides settings to select and configure the trigger, like trigger source, trigger mode and trigger delays, and to arm or trigger an internal trigger manually. The header of the tab displays the status of the trigger signal and trigger mode.
Page 152 ® Signal control and signal characteristics R&S SMW-K60/-K117/-K178 Trigger settings Arm..........................154 Execute Trigger......................154 Source.........................154 Sync. Output to Ext. Trigger/Sync. Output to Trigger..........154 External Inhibit/Trigger Inhibit..................155 External Delay/Trigger Delay..................156 Trigger Settings Common to All Basebands To enable simultaneous signal generation in all basebands, the R&S SMW200A cou- ples the trigger settings in the available basebands in any instrument's configuration involving signal routing with signal addition.
Page 153 ® Signal control and signal characteristics R&S SMW-K60/-K117/-K178 Trigger settings Remote command: on page 296 [:SOURce<hw>]:BB:BTOoth:TRIGger:SLUNit Signal Duration Requires trigger "Mode" > "Single". Enters the length of the trigger signal sequence. Use this parameter, for example, for the following applications: ●...
Page 154 ® Signal control and signal characteristics R&S SMW-K60/-K117/-K178 Trigger settings "Time" Sets the time of the time-based trigger in format hh:mm:ss. Remote command: on page 294 [:SOURce<hw>]:BB:BTOoth:TRIGger:TIME:TIME Stops the signal generation until subsequent trigger event occurs. Remote command: on page 296 [:SOURce<hw>]:BB:BTOoth:TRIGger:ARM:EXECute Execute Trigger For internal trigger source, executes trigger manually.
Page 155 ® Signal control and signal characteristics R&S SMW-K60/-K117/-K178 Trigger settings Corresponds to the default state of this parameter. The signal calculation starts simultaneously with the trigger event. Because of the processing time of the instrument, the first samples are cut off and no signal is out- put.
Page 156: Marker Settings
® Signal control and signal characteristics R&S SMW-K60/-K117/-K178 Marker settings Remote command: on page 297 [:SOURce<hw>]:BB:BTOoth:TRIGger[:EXTernal]:INHibit on page 297 [:SOURce<hw>]:BB:BTOoth:TRIGger:OBASeband:INHibit External Delay/Trigger Delay Delays the trigger event of the signal from: ● The external trigger source ● The other path ●...
Page 157 ® Signal control and signal characteristics R&S SMW-K60/-K117/-K178 Marker settings The R&S SMW200A adds the marker signal to the baseband signal. Also, R&S SMW200A outputs this signal at the configured USER x connector. About marker output signals This section focuses on the available settings. For detailed information on baseband trigger signals, see section About trigger signals"...
Page 158 ® Signal control and signal characteristics R&S SMW-K60/-K117/-K178 Marker settings "Pulse" A regular marker signal is generated. The pulse frequency is defined by entering a divider. The frequency is derived by dividing the sample rate by the divider. The input box for the divider opens when "Pulse" is selected, and the resulting pulse frequency is displayed below it.
Page 159: Clock Settings
® Signal control and signal characteristics R&S SMW-K60/-K117/-K178 Clock settings 7.5 Clock settings Access: ► Select "Baseband" > "Bluetooth" > "Clock". This tab provides settings to select and configure the clock signal, like the clock source and clock mode. Defining the clock 1.
Page 160: Local And Global Connectors Settings
® Signal control and signal characteristics R&S SMW-K60/-K117/-K178 Local and global connectors settings How to: "Defining the clock" on page 159 Remote command: on page 303 [:SOURce<hw>]:BB:BTOoth:CLOCk:SOURce Clock Mode Option: R&S SMW-B10 Sets the type of externally supplied clock. Remote command: on page 302 [:SOURce<hw>]:BB:BTOoth:CLOCk:MODE Measured External Clock...
Page 161: Remote Control Commands
® Remote control commands R&S SMW-K60/-K117/-K178 8 Remote control commands The following commands are required to perform signal generation with the Bluetooth options in a remote environment. We assume that the R&S SMW200A has already been set up for remote operation in a network as described in the R&S SMW200A doc- umentation.
Page 162: General Commands
® Remote control commands R&S SMW-K60/-K117/-K178 General commands The following chapters describe the commands specific to the Bluetooth options R&S SMW-K60, R&S SMW-K117 and R&S SMW-K178. ● General commands....................162 ● Dirty transmitter configuration................167 ● Channel configuration commands - LE..............174 ●...
Page 163 ® Remote control commands R&S SMW-K60/-K117/-K178 General commands Example: To configure general Bluetooth BR/EDR settings // ****************************************************************** // Set time unit to ms. // ****************************************************************** :SOURce1:BB:BTOoth:UNIT:TIME MS // ****************************************************************** // Set frequency and level. // Set BR/EDR PHY and transport modes. // Query the version of the digital standard.
Page 164 ® Remote control commands R&S SMW-K60/-K117/-K178 General commands ................167 [:SOURce<hw>]:BB:BTOoth:UNIT:TIME ................167 [:SOURce<hw>]:BB:BTOoth:VERSion? ............... 167 [:SOURce<hw>]:BB:BTOoth:WAVeform:CREate [:SOURce<hw>]:BB:BTOoth:BCText? Queries the state and controller role. Return values: <BcText> string Connected (only data channel type) Advertiser (only advertising channel type) ADV_IND, ADV_DIRECT_IND, ADV_NONCONN_IND, ADV_SCAN_IND Within R&S SMW-K117 also ADV_EXT_IND, AUX_ADV_IND, AUX_SYNC_IND, AUX_CHAIN_IND Scanner...
Page 165 ® Remote control commands R&S SMW-K60/-K117/-K178 General commands Manual operation: "Bluetooth Mode" on page 37 [:SOURce<hw>]:BB:BTOoth:PRESet Sets the parameters of the digital standard to their default values (*RST values speci- fied for the commands). Not affected is the state set with the command SOURce<hw>:BB:BTOoth:STATe. Example: Example"To save and recall settings"...
Page 166 ® Remote control commands R&S SMW-K60/-K117/-K178 General commands [:SOURce<hw>]:BB:BTOoth:SETTing:STORe <Filename> Saves the current settings into the selected file; the file extension (*.bto) is assigned automatically. Setting parameters: <Filename> string file name or complete file path Example: Example"To save and recall settings" on page 162.
Page 167: Dirty Transmitter Configuration
® Remote control commands R&S SMW-K60/-K117/-K178 Dirty transmitter configuration [:SOURce<hw>]:BB:BTOoth:UNIT:TIME <Time> Sets the time unit for remote control commands. Parameters: <Time> S | MS *RST: Example: Example"To configure time units for timing and delay com- mands" on page 162. [:SOURce<hw>]:BB:BTOoth:VERSion? Queries the version of the specification for Bluetooth wireless technology underlying the definitions.
Page 168 ® Remote control commands R&S SMW-K60/-K117/-K178 Dirty transmitter configuration // ****************************************************************** // Reset dirty transmitter. Set frequency drift rate, start phase, // frequency drift deviation and number of packets // per dirty transmitter set (LE only). Enable dirty transmitter. // ****************************************************************** SOURce1:BB:BTOoth:DTTest:STDefault SOURce1:BB:BTOoth:DTTest:FDRate 1.25 SOURce1:BB:BTOoth:DTTest:SPHase 0...
Page 169 ® Remote control commands R&S SMW-K60/-K117/-K178 Dirty transmitter configuration Parameters: <DttState> 1 | ON | 0 | OFF *RST: Example: Example"To configure a dirty transmitter" on page 167. Manual operation: "Dirty Transmitter Test" on page 41 [:SOURce<hw>]:BB:BTOoth:DTTest:FDDeviation <FdDeviation> Sets a frequency drift rate. A sine wave is used to drift the modulated Bluetooth signal around center frequency + carrier frequency offset.
Page 170 ® Remote control commands R&S SMW-K60/-K117/-K178 Dirty transmitter configuration Options: R&S SMW-K117 Manual operation: "Modulation Index Mode" on page 41 [:SOURce<hw>]:BB:BTOoth:DTTest:NPPSet <NumPack> Specifies the number of packets per dirty transmitter set. Specifies the number of packets or CS steps per dirty transmitter set. Bluetooth mode Channel type Number of packets...
Page 171 ® Remote control commands R&S SMW-K60/-K117/-K178 Dirty transmitter configuration Example: SOURce1:BB:BTO:DTT:STD calls the default settings. Example: See also Example"To configure a dirty transmitter" on page 167. Usage: Event Manual operation: "Set To Default" on page 40 [:SOURce<hw>]:BB:BTOoth:DTTest:TABLe <Table> Opens the table settings. Parameters: <Table>...
Page 172 ® Remote control commands R&S SMW-K60/-K117/-K178 Dirty transmitter configuration with = "symbol rate" , set with the command [:SOURce<hw>]:BB:BTOoth:SRATe: VARiation = "frequency deviation", set with the command [:SOURce<hw>]:BB:BTOoth: MSETtings:FDEViation According to the Bluetooth standard, the modulation index is allowed to vary between 0.28 and 0.35.
Page 173 ® Remote control commands R&S SMW-K60/-K117/-K178 Dirty transmitter configuration [:SOURce<hw>]:BB:BTOoth:DTTest:TABLe:LONG:SET<ch>:STERror <StError> Sets a symbol timing error in ppm. This parameter modifies the symbol clock frequency by the set value. Parameters: <StError> integer Range: -150 to 150 *RST: Default unit: ppm Example: SOURce1:BB:BTO:PTYP DH1 sets the packet type.
Page 174: Channel Configuration Commands - Le
® Remote control commands R&S SMW-K60/-K117/-K178 Channel configuration commands - LE Parameters: <State> 1 | ON | 0 | OFF *RST: Example: SOURce1:BB:BTO:PTYP DH1 sets the packet type. SOURce1:BB:BTO:DTT:TABL SHOR sets the table type SOURce1:BB:BTO:DTT:TABL:SHOR:SET2:STAT ON activates the set 2 in the short table. Example: See also Example"To configure a dirty transmitter"...
Page 175 ® Remote control commands R&S SMW-K60/-K117/-K178 Channel configuration commands - LE SOURce1:BB:BTOoth:CTYPe DATA SOURce1:BB:BTOoth:UPTYpe TPAC SOURce1:BB:BTOoth:PFORmat L2M SOURce1:BB:BTOoth:USLength 2 SOURce1:BB:BTOoth:BCRole CENTral SOURce1:BB:BTOoth:CCRC:STATe 1 // ****************************************************************** // Alternatively set duty cycle for ADV_DIRECT_IND // ****************************************************************** SOURce1:BB:BTOoth:CTYPe ADV SOURce1:BB:BTOoth:UPTYpe ADIN SOURce1:BB:BTOoth:DCYCle LOW ................175 [:SOURce<hw>]:BB:BTOoth:BCRole ...............
Page 176 ® Remote control commands R&S SMW-K60/-K117/-K178 Channel configuration commands - LE [:SOURce<hw>]:BB:BTOoth:CCRC:STATe <State> Enables/disables the corruption of CRC for every second generated packet. If enabled, only 50% of packets are generated with correct CRC. Parameters: <State> 1 | ON | 0 | OFF *RST: Example: Example"To configure general channel settings for LE"...
Page 177 ® Remote control commands R&S SMW-K60/-K117/-K178 Channel configuration commands - LE [:SOURce<hw>]:BB:BTOoth:PFORmat <PFormat> Selects the packet format that is the format according to the physical layer (PHY) that supports the packet type or PDU type. Parameters: <PFormat> L1M | L2M | LCOD | L2M2B LE uncoded PHY with 1 Msymbol/s modulation.
Page 178 ® Remote control commands R&S SMW-K60/-K117/-K178 Channel configuration commands - LE Table 8-2: R&S SMW-K117 packet/PDU types <UpType> Packet/PDU type <UpType> Packet/PDU type PREQ LL_PHY_REQ ACINd AUX_CHAIN_IND PRSP LL_PHY_RSP ASINd AUX_SYNC_IND PUIN LL_PHY_UPDATE_IND ASReq AUX_SCAN_REQ LREQ LL_LENGTH_REQ ASPSp AUX_SCAN_RSP LRSP LL_LENGTH_RSP ACRSp AUX_CONNECT_RSP...
Page 179 ® Remote control commands R&S SMW-K60/-K117/-K178 Channel configuration commands - LE [:SOURce<hw>]:BB:BTOoth:USLength <UsLength> Selects the number of frames or events depending on the packet type. The signal repeats after the specified number of frames/events. For SCAN_REQ and CONNECT_IND packet, the sequence length is expressed in "Frames".
Page 180: Event And Frame Configuration Commands - Le
® Remote control commands R&S SMW-K60/-K117/-K178 Event and frame configuration commands - LE [:SOURce<hw>]:BB:BTOoth:DURation <Duration> Sets the transmission duration for continuous payload transmission. This transmission requires a CONTINUOUS packet: :SOURce1:BB:BTOoth:UPTYpe CONT Command sets the values in ms. Query returns values in s. The duration range, increment and default value depend on the modulation format, symbols per a bit and payload type.
Page 181 ® Remote control commands R&S SMW-K60/-K117/-K178 Event and frame configuration commands - LE // ****************************************************************** SOURce1:BB:BTOoth:CTYPe ADV SOURce1:BB:BTOoth:UPTYpe SREQ SOURce1:BB:BTOoth:ECONfiguration:SWINdow 10 SOURce1:BB:BTOoth:ECONfiguration:SINTerval 3500 // ****************************************************************** // For packet type CONNECT_IND set transmit window, // start point of the transmit window, // LL connection timeout and time interval.
Page 182 ® Remote control commands R&S SMW-K60/-K117/-K178 Event and frame configuration commands - LE ......187 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:PAINterval ......187 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:PPERiodicity ......187 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:RCECount ............. 188 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PNUMber ............188 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:SDCI? ............. 188 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:SINTerval .............189 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:SWINdow ............189 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:WOINfo? ............190 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:WSINfo? [:SOURce<hw>]:BB:BTOoth:ECONfiguration:ACTable:CHANnel<ch0>:STATe <State> [:SOURce<hw>]:BB:BTOoth:ECONfiguration:DCTable:CHANnel<ch0>:STATe <State> [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:DCMTable: CHANnel<ch0>:STATe <State>...
Page 183 ® Remote control commands R&S SMW-K60/-K117/-K178 Event and frame configuration commands - LE Parameters: <AeDelay> float Range: 0 s to 10E-3 s Increment: 0.1E-3 *RST: Default unit: ms Example: SOURce1:BB:BTO:ECON:AEDelay 5 Sets a delay of 5 ms. Example: See also Example"Configure event and frame configuration set- tings"...
Page 184 ® Remote control commands R&S SMW-K60/-K117/-K178 Event and frame configuration commands - LE Example: See also Example"Configure event and frame configuration set- tings" on page 180. Manual operation: "Advertising Event Interval" on page 52 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:APINterval <ApInterval> Sets the time interval between packets starting points of two consecutive packets in the advertising channel.
Page 185 ® Remote control commands R&S SMW-K60/-K117/-K178 Event and frame configuration commands - LE [:SOURce<hw>]:BB:BTOoth:ECONfiguration:LTKey <LtKey>, <BitCount> Indicates the time the controller needs to receive the long-term key from the host. After this time, the controller is ready to enter into the last phase of encryption mode setup. Parameters: <LtKey>...
Page 186 ® Remote control commands R&S SMW-K60/-K117/-K178 Event and frame configuration commands - LE Parameters: <MInterval> float Range: 7.5E-3 s to 4000E-3 s Increment: 1.25E-3 *RST: 7.5E-3 Example: SOURce1:BB:BTO:ECON:PCON:MXIN 12.5 Sets a time interval of 12.5 ms. Example: See also Example"Configure event and frame configuration set- tings"...
Page 187 ® Remote control commands R&S SMW-K60/-K117/-K178 Event and frame configuration commands - LE Options: R&S SMW-K117 Manual operation: "Offset Setting Table" on page 85 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:PAINterval <Interval> Sets the time interval between the start of two AUX_SYNC_IND PDUs from the same advertising set.
Page 188 ® Remote control commands R&S SMW-K60/-K117/-K178 Event and frame configuration commands - LE Parameters: <RCECount> integer Range: 0 to 65535 *RST: Example: Example"Configure event and frame configuration settings" on page 180. Options: R&S SMW-K117 Manual operation: "Ref. Connection Event Count" on page 85 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PNUMber <PNumber>...
Page 189 ® Remote control commands R&S SMW-K60/-K117/-K178 Event and frame configuration commands - LE Command sets the values in ms. Query returns values in s. Parameters: <SInterval> float Range: 10E-3 s to depends on oversampling and the num- ber of advertsing channel table states Increment: 0.625E-3 *RST: 10E-3...
Page 190: Channel Sounding Commands - Le
® Remote control commands R&S SMW-K60/-K117/-K178 Channel sounding commands - LE Example: SOURce1:BB:BTO:UPTY CREQ Sets packet type CONNECT_IND SOURce1:BB:BTO:ECON:PCON:WOIN? Queries the start point of the transmit window. Example: See also Example"Configure event and frame configuration set- tings" on page 180. Usage: Query only [:SOURce<hw>]:BB:BTOoth:ECONfiguration:WSINfo?
Page 191: Cs General Commands
® Remote control commands R&S SMW-K60/-K117/-K178 Channel sounding commands - LE 8.5.1 CS general commands Example: To configure CS sequence settings :SOURce1:BB:BTOoth:CINTerval 10 // The connection interval is 10 microseconds. :SOURce1:BB:BTOoth:EINTerval 2 // The number of event intervals is two. :SOURce1:BB:BTOoth:EOFFset? // Response: "500"...
Page 192: Cs Subevent Commands
® Remote control commands R&S SMW-K60/-K117/-K178 Channel sounding commands - LE [:SOURce<hw>]:BB:BTOoth:CS:EOFFset <EventOffset> Sets the time between the anchor point of the LE connection event and the beginning of the CS event. Parameters: <EventOffset> integer Range: 500 to 4e6 *RST: Example: Example"To configure CS sequence settings"...
Page 193 ® Remote control commands R&S SMW-K60/-K117/-K178 Channel sounding commands - LE // ***************************************************************************** // Configure channel selection settings of a CS subevent. // ***************************************************************************** :SOURce1:BB:BTOoth:CS:CFCHm? // Response: "#H00000000000000000001,80" // CSFilteredChM value is 00000000000000000001 in hexadecimal reperesentation. :SOURce1:BB:BTOoth:CS:CMRepetition 1 // Sets one cycle of the ChM field for non-Mode-0 steps within the CS procedure. :SOURce1:BB:BTOoth:CS:CSEL? // Response: "SEL_3B"...
Page 194 ® Remote control commands R&S SMW-K60/-K117/-K178 Channel sounding commands - LE For :SOURce1:BB:BTO:CS:SNUM 2 or higher, settable subevent intervals depend on the number of event intervals, the connection interval, the event offset and the sube- vent length. See also on page 194. [:SOURce<hw>]:BB:BTOoth:CS:SNUMber Parameters: <SubInterval>...
Page 195 ® Remote control commands R&S SMW-K60/-K117/-K178 Channel sounding commands - LE Setting requires manual step scheduling. Settable minimum values are 1 or equal to the number of non-zero Mode-0 steps. See also [:SOURce<hw>]:BB:BTOoth:CS: on page 194. SSCHeduling Parameters: <NumOfSteps> integer Range: 2 to 160 *RST:...
Page 196: Cs Step Configuration Commands
® Remote control commands R&S SMW-K60/-K117/-K178 Channel sounding commands - LE 8.5.3 CS step configuration commands Example: To configure CS steps for subevent 0 // ***************************************************************************** // Configure general CS step settings of the first subevent "Subevent 0". // ***************************************************************************** // Configure general subevent settings.
Page 197 ® Remote control commands R&S SMW-K60/-K117/-K178 Channel sounding commands - LE For an overview on available submodes per main mode, see Table 5-8. Parameters: <mainMode> MODE1 | MODE2 | MODE3 MODE1 Mode-1 mode with no submode available. MODE2 Mode-2 mode with submodes Mode-1 and Mode-3 available. MODE3 Mode-3 mode with submodes Mode-1 and Mode-2 available.
Page 198 ® Remote control commands R&S SMW-K60/-K117/-K178 Channel sounding commands - LE Example: Example"To configure CS subevent settings" on page 192. Manual operation: "Main_Mode_Min_Steps" on page 101 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:MMSTeps? Queries the number of main mode CS steps. Return values: <MMSTeps> integer Range: 2 to 160 *RST: Example:...
Page 199 ® Remote control commands R&S SMW-K60/-K117/-K178 Channel sounding commands - LE Parameters: <TIPO> TIP1_10 | TIP1_20 | TIP1_30 | TIP1_40 | TIP1_50 | TIP1_60 | TIP1_80 | TIP1_145 TIP1_x, x represents values in microseconds. *RST: TIP1_145 Example: Example"To configure CS subevent settings" on page 192.
Page 200 ® Remote control commands R&S SMW-K60/-K117/-K178 Channel sounding commands - LE Manual operation: "T_PM" on page 105 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:MTHRee:TIPT <TIPT> [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:MTWO:TIPT <TIPT> Sets the time "T_IP2" for Mode-2 or Mode-3 CS steps. Parameters: <TIPT> TIP2_10 | TIP2_20 | TIP2_30 | TIP2_40 | TIP2_50 | TIP2_60 | TIP2_80 | TIP2_145 TIP2_x, x represents values in microseconds.
Page 201 ® Remote control commands R&S SMW-K60/-K117/-K178 Channel sounding commands - LE Select the file from the default instrument directory or a specific directory. Parameters: <UserPayload> string Example: Example"To configure CS step settings for a subevent" on page 202. Manual operation: "Select Data List"...
Page 202: Cs Step Info Commands
® Remote control commands R&S SMW-K60/-K117/-K178 Channel sounding commands - LE 8.5.4 CS step info commands Example: To configure CS step settings for a subevent // ***************************************************************************** // Configure general settings of a CS subevent. // ***************************************************************************** // Configure general subevent settings. :SOURce1:BB:BTOoth:CS:SLENgth 1250 // CS subevent sequence length is 1250 microseconds.
Page 203 ® Remote control commands R&S SMW-K60/-K117/-K178 Channel sounding commands - LE [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>][:STEP<st0>]:CINDex <ChannlIndex> Queries the channel index for individual CS steps. Parameters: <ChannlIndex> integer Range: 0 to 78 *RST: Example: Example"To configure CS step settings for a subevent" on page 202. Manual operation: "Channel Index"...
Page 204 ® Remote control commands R&S SMW-K60/-K117/-K178 Channel sounding commands - LE <BitCount> integer Range: 32 to 128 *RST: Example: Example"To configure CS step settings for a subevent" on page 202. Manual operation: "Sounding Sequence Content/Random Sequence Content" on page 110 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>][:STEP<st0>]:CSIGnal <CompanionSignal>...
Page 205: Cs Channel Table Commands
® Remote control commands R&S SMW-K60/-K117/-K178 Channel sounding commands - LE Select the file from the default instrument directory or a specific directory. Parameters: <DataList> string Example: Example"To configure CS step settings for a subevent" on page 202. Manual operation: "Companion Signal"...
Page 206 ® Remote control commands R&S SMW-K60/-K117/-K178 Channel sounding commands - LE Return values: <CenterFreq> float For a description, see also table Table 2-13. Range: 2402 to 2480 Increment: 2 *RST: 2402 Example: Example"To configure CS subevent settings" on page 192. Usage: Query only Manual operation:...
Page 207: Cs Security Commands
® Remote control commands R&S SMW-K60/-K117/-K178 Channel sounding commands - LE 1|ON Enables transmission of the subevent for the selected channel. 0|OFF Disables transmission of the subevent for the selected channel. *RST: Example: Example"To configure CS subevent settings" on page 192. Manual operation: "Channel Allowed"...
Page 208 ® Remote control commands R&S SMW-K60/-K117/-K178 Channel sounding commands - LE <BitCount> integer Fixed bit count of 64 bits. Range: 64 to 64 *RST: Example: Example"To configure CS subevent settings" on page 192. Manual operation: "CS_IV_P(hex)" on page 97 [:SOURce<hw>]:BB:BTOoth:CS:CINC <CsInC>, <BitCount> Requires packet type CS SEQUENCE or LL_CS_SEC_REQ.
Page 209: Cs Channel Selection Commands
® Remote control commands R&S SMW-K60/-K117/-K178 Channel sounding commands - LE [:SOURce<hw>]:BB:BTOoth:CS:CSPVc <csPvC> Parameters: <csPvC> 64 bits Manual operation: "CS_PV_C(hex)" on page 97 [:SOURce<hw>]:BB:BTOoth:CS:CPVP <CsPvP>, <BitCount> Requires packet type CS SEQUENCE or LL_CS_SEC_REQ. Sets the CS_PV_P parameter. The parameter is 64-bit in hexadecimal representation. Parameters: <CsPvP>...
Page 210 ® Remote control commands R&S SMW-K60/-K117/-K178 Channel sounding commands - LE Return values: <CsFilteredChM> numeric CSFilteredChM value in hexadecimal representation. *RST: Example: Example"To configure CS subevent settings" on page 192. Usage: Query only Manual operation: "CSFilteredChM(hex)" on page 98 [:SOURce<hw>]:BB:BTOoth:CS:CMRepetition <ChMRepetition> Sets the 3-bit ChM_Repetition field.
Page 211: Packet Configuration Commands - Le
® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE Parameters: <ChThreeCJump> JUMP_2 | JUMP_3 | JUMP_4 | JUMP_5 | JUMP_6 | JUMP_7 | JUMP_8 For Ch3cJump field parameters, see Table 5-7. *RST: JUMP_2 Example: Example"To configure CS subevent settings" on page 192.
Page 212 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE // ****************************************************************** // Alternatively set periodic advertising interval for AUX_SYNC_IND // ****************************************************************** SOURce1:BB:BTOoth:CTYPe ADV SOURce1:BB:BTOoth:UPTYpe ASIN SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:PAINterval // ****************************************************************** // Select packet type AUX_ADV_IND. (All parameters of // extended header are configurable with AUX_ADV_IND packet // type.) Set channel selection, // Tx device address type, advertising mode.
Page 213 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:ADID #H01FF,12 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:ASID #H0F,4 // ****************************************************************** // Enable and specify AuxPtr for the secondary advertising // channel: select AUX channel, set clock accuracy, offset unit, // AUX offset, AUX PHY. // ****************************************************************** SOURce1:BB:BTOoth:ECONfiguration:PCON:EHFLags:APTR:STATe ON SOURce1:BB:BTOoth:ECONfiguration:DCTable:CHANnel0:STATe 1...
Page 214 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE Example: To configure data packets // ****************************************************************** // Configure signal for DATA: select channel type, packet type, // packet format, sequence length, role, enable CRC corruption. // ****************************************************************** SOURce1:BB:BTOoth:CTYPe DATA SOURce1:BB:BTOoth:UPTYpe CUR SOURce1:BB:BTOoth:PFORmat L1M SOURce1:BB:BTOoth:USLength 12...
Page 215 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit1:STATe 1 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit2:STATe 1 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit3:STATe 1 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit4:STATe 1 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit5:STATe 1 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit6:STATe 1 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit7:STATe 0 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit8:STATe 1 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit9:STATe 0 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit10:STATe 0 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit11:STATe 0 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit12:STATe 0 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit13:STATe 0 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit14:STATe 1 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit15:STATe 0 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit16:STATe 0 // ****************************************************************** // Configure the payload of LL_CONNECTION_PARAM_REQ: max.
Page 216 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE // ****************************************************************** // Set the payload of LL_PHY_REQ: specify preferred Tx, Rx PHYs. // ****************************************************************** SOURce1:BB:BTOoth:CTYPe DATA SOURce1:BB:BTOoth:UPTYpe PREQ SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:TPHYs:L1M:STATe 1 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:TPHYs:L2M:STATe 1 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:TPHYs:LCOD:STATe 0 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:RPHYs:L1M:STATe 1 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:RPHYs:L2M:STATe 1 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:RPHYs:LCOD:STATe 0 // ****************************************************************** // Set the payload of LL_PHY_UPDATE_IND: specify PHYs for...
Page 217: General Configuration
® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE // configure CTE method, set event counter properties, specify PHYs // and address type. // ****************************************************************** SOURce1:BB:BTOoth:CTYPe DATA SOURce1:BB:BTOoth:UPTYpe PSIN SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:CPResent 1 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:CTIMe 0.016 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:CTYPe AOD1 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:ANTNumber 4 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:ANTGain0? // Response: "0"...
Page 218 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:DWHitening <DWhitening> Activates or deactivates the Data Whitening. Evenly distributed white noise is ideal for the transmission and real data can be forced to look similar to white noise with different methods called Data Whitening.
Page 219: Header Configuration
® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE 8.6.2 Header configuration ......219 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CSELection ....... 219 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:NSValue ....... 219 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SSValue ......220 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CPResent ........220 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CTIMe ......... 220 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CTReq ......... 221 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CTYPe ......... 221 [:SOURce<hw>]:BB:BTOoth:ECONfig:PCONfig:ANTGain<ch0> ..........221 [:SOURce<hw>]:BB:BTOoth:ECONfig:PCONfig:ANTNumber [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CSELection <CSelection>...
Page 220 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE Example: Example"To configure data packets" on page 214. Manual operation: "SN Start Value" on page 61 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CPResent <State> Activates the CTEInfo field in the header of Bluetooth LE data packets in the LE unco- ded PHY.
Page 221 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CTYPe <CType> Sets the type of constant tone extension. The type specifies the CTE AoA/AoD method and for AoD the length of the switching and I/Q sampling slots. Parameters: <CType>...
Page 222: Payload Configuration
® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE 8.6.3 Payload configuration ........224 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ACAD ....224 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ACAD:APATtern ....225 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ACAD:ASELection ........225 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ACID ......225 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ACASsigned ......225 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SCASsigned ........225 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SCID ......225 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ICASsigned ........225 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ICID ........226 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ADID ........226 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ALAP ........226 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ILAP...
Page 223 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE ....... 237 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SIVector ......238 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MROCtets ......238 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MTOCtets ........238 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MSKD ........238 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SSKD ....... 239 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MRTime ........239 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MTTime ......239 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MUCHannels ....239 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MTSPhy:L1M:STATe ....239 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MTSPhy:L2M:STATe ... 239 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MTSPhy:LCOD:STATe ....239 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:STMPhy:L1M:STATe ....239 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:STMPhy:L2M:STATe...
Page 224 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE ....250 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:PHY:LCOD:STATe ......250 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SCECounter ........251 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SID [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ACAD <Data> Specifies the pattern source used for additional controller advertising data (ACAD). Parameters: <Data> ALL0 | ALL1 | PATTern | PN09 | PN11 | PN15 | PN16 | PN20 | PN21 | PN23 | DLISt ALL0 / ALL1 All 0 or all 1 pattern...
Page 225 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE Manual operation: "AList / Pattern" on page 70 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ACAD:ASELection <DSelection> Specifies data list file. The settings is relevant for [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ACADDLISt Parameters: <DSelection> string Path and file name. Example: Example"To configure advertising packets" on page 211.
Page 226 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE <BitCount> integer Range: 24 to 24 *RST: Example: Example"To configure advertising packets" on page 211. Manual operation: "Initiator's Device Addr" on page 77 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ADID <Adid>, <BitCount> Specifies "Advertising Data ID" in hexadecimal format to be signaled within an exten- ded header.
Page 227 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE Manual operation: "Target's Device Addr" on page 65 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ALENgth <Length> Specifies the length of ACAD data pattern. Parameters: <Length> integer Range: 0 to 62 *RST: Example: Example"To configure advertising packets" on page 211.
Page 228 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE <BitCount> integer Range: 24 to 24 *RST: Example: Example"To configure advertising packets" on page 211. Options: R&S SMW-K117 Manual operation: "Target's Device Addr" on page 65 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:AOFFset <AOffset> Specifies the time from the start of the packet containing the AuxPtr field to the approx- imate start of the auxiliary packet.
Page 229 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE Parameters: <APhy> L1M | L2M | LCOD | L2M2B For a description, see [:SOURce<hw>]:BB:BTOoth:PFORmat on page 177. *RST: Example: Example"To configure advertising packets" on page 211. Options: L2M and LCOD require option R&S SMW-K117. L2M2B requires option R&S SMW-K178.
Page 230 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CID <Cid>, <BitCount> Sets the company identifier of the manufacturer of the Bluetooth Controller. A 16 bit value is set. Note: This parameter is relevant for data frame configuration and for the packet type LL_VERSION_IND.
Page 231 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE Manual operation: "Connection Event Interval" on page 55 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:DATA <Data> Selects the pattern source used for the payload. Parameters: <Data> ALL0 | ALL1 | PATTern | PN09 | PN11 | PN15 | PN16 | PN20 | PN21 | PN23 | DLISt ALL0 / ALL1 All 0 or all 1 pattern...
Page 232 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:DATA:DSELection <DSelection> Selects a data list file from the default directory or from the specific directory. Using data list (DLISt) data requires one of the following commands: ● BB:BTO:ECON:PCON:DATA DLISt [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration: on page 231.
Page 233 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE <BitCount> integer Range: 8 to 8 *RST: Example: SOURce1:BB:BTO:ECON:PCON:ECOD #H00,8 Sets the error code. Manual operation: "Error Code(hex)" on page 82 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ECOunter <ECounter> Counts the AUX_SYNC_IND packets that the SyncInfo field describes. Parameters: <ECounter>...
Page 234 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE Example: Example"To configure advertising packets" on page 211. Options: R&S SMW-K117 Manual operation: "Extended Header" on page 67 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:EHFLags: AADDress:STATe <State> If enabled, the R&S SMW200A includes the signaling of non-significant advertising address part (NAP) and upper address part (UAP).
Page 235 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:EHFLags:CINFo: STATe <State> Activates the CTEInfo field in the extended header of Bluetooth LE advertising packets in the LE uncoded PHY. Parameters: <State> 1 | ON | 0 | OFF *RST: Example: Example"To configure advertising packets"...
Page 236 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE Example: Example"To configure advertising packets" on page 211. Options: R&S SMW-K117 Manual operation: "TxPow(dBm)" on page 69 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit<ch0>:STATe <State> Requires link layer control PDUs LL_FEATURE_REQ, LL_FEATURE_RSP or LL_PERIPHERAL_FEATURE_REQ, see [:SOURce<hw>]:BB:BTOoth:UPTYpe on page 177.
Page 237 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE The Central and Peripherals determine the data channel in use for every connection event from the channel map. Hop_length is set for the LL connection and communica- ted in the CONNECT_IND and LL_CHANNEL_MAP_IND packets. Parameters: <HLength>...
Page 238 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE Example: SOURce1:BB:BTO:ECON:PCON:MIV #H0000000000000000,32 (Central). SOURce1:BB:BTO:ECON:PCON:SIV #H0000000000000000,32 (Peripheral). [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MROCtets <MROctets> [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MTOCtets <MTOctets> Specifies the maximum allowed payload length of a packet to be received (..:MROCtets) or transmitted (..:MTOCtets). Information is signaled via LL_LENGTH_REQ and LL_LENGTH_RSP.
Page 239 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MRTime <MRTime> [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MTTime <MTTime> Specifies the maximum allowed time to receive (..:MRTime) or transmit (..:MTTime) a packet. Information is signaled via LL_LENGTH_REQ and LL_LENGTH_RSP. Parameters: <MTTime> float Range: 0.328E-3 to 17.04E-3 Increment: 0.001E-3 *RST: 17.04E-3...
Page 240 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE You can enable one or more PHYs: ● L1M: for LE uncoded 1 Msymbol/s PHY. ● L2M: for LE uncoded 2 Msymbol/s PHY. ● LCOD: for LE coded 1 Msymbol/s PHY. Parameters: <STMP>...
Page 241 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:NSLatency <NsLatency> Requires a data event and advertising frame configuration with the packet type LL_CONNECTION_UPDATE_IND. Sets the number of consecutive connection events the Peripheral can ignore for asym- metric link layer connections. Parameters: <NsLatency>...
Page 242 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE Example: Example"To configure data packets" on page 214. Manual operation: "Transmit Window Size" on page 77 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:OADJust <State> Adjusts the "Sync Packet Offset" automatically to the next value, which is a multiple of the ""Offset Units".
Page 243 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE Depending on the Bluetooth controller role either Tx or Rx or both address types are assigned. Subdivided into private and random, a Bluetooth LE device address consits of 48 bits. The format of the device address differs depending on the selected address type.
Page 244 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:TPHYs:L2M:STATe <TPhys> [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:TPHYs:LCOD: STATe <TPhys> Specifies preferred physical layers in Rx (..:RPHYs:..) or Tx (..:TPHYs:..) direc- tion. Information is signaled via LL_PHY_REQ and LL_PHY_RSP. You can enable one or more PHYs: :L1M: for LE uncoded 1 Msymbol/s PHY, :L2M: for LE uncoded 2 Msymbol/s PHY, and :LCOD: for LE coded 1 Msymbol/s PHY.
Page 245 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE Example: SOURce1:BB:BTO:ECON:PCON:SCAC SCA1 Sets the encoding value. Manual operation: "Sleep Clock Accuracy" on page 79 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SLATency <SLatency> Requires data event and advertising frame configuration with the packet type CON- NECT_IND.
Page 246 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SPOFfset <SPOffset> Specifies the time from the start of the AUX_ADV_IND packet containing the SyncInfo field to the start of the AUX_SYNC_IND packet. The offset is determined by multiplying the value by the unit, see [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SOUNits Parameters:...
Page 247 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE Manual operation: "TxPow(dBm)" on page 69 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:UTYPe <UType>, <BitCount> Enables that an invalid control packet is indicated. The CtrType field indicates the value of the LL control packet that caused the transmis- sion of this packet.
Page 248 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE Parameters: <WOffset> float Range: 0 s to depending on connection event interval Increment: 1.25E-3 s *RST: Default unit: ms Example: Example"Configure event and frame configuration settings" on page 180. Manual operation: "Transmit Window Offset"...
Page 249 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE Example: Example"To configure data packets" on page 214. Manual operation: "Connection Event Count" on page 87 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ID <Id>, <BitCount> Specifies the ID in the CtrData field of the LL_PERIODIC_SYNC_IND PDU. Parameters: <Id>...
Page 250 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:PHY:L1M:STATe <State> Sets the LE 1M PHY in the CtrData field of the LL_PERIODIC_SYNC_IND PDU. Parameters: <State> 1 | ON | 0 | OFF *RST: Example: Example"To configure data packets" on page 214.
Page 251: Cs Payload Configuration
® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SID <Sid>, <BitCount> Specifies the SID in the CtrData field of the LL_PERIODIC_SYNC_IND. Parameters: <Sid> numeric *RST: <BitCount> integer Range: 4 to 4 *RST: Example: Example"To configure data packets" on page 214.
Page 252 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE // ***************************************************************************** // Configure and check LL_CS_CAPABILITIES_REQ PDU settings. // ***************************************************************************** :SOURce1:BB:BTOoth:CS:CDATA:CSPCapability? // Response: "LE2M" // The PHY is LE 2M. :SOURce1:BB:BTOoth:CS:CDATa:MAPath 1 :SOURce1:BB:BTOoth:CS:CDATa:MPSupported 1 :SOURce1:BB:BTOoth:CS:CDATa:MTYPe? // Response: "MODE3" // The mode type is Mode-3.
Page 253 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE // ***************************************************************************** :SOURce1:BB:BTOoth:CS:CDATa:ECODe #HFF,8 // Sets the error code "FF" in hexadecimal representation. // ***************************************************************************** // Configure and check LL_CS_IND PDU settings. // ***************************************************************************** :SOURce1:BB:BTOoth:CS:CDATa:EOFFset 500 // Sets an event offset of 500 microseconds. // ***************************************************************************** // Configure and check LL_CS_REQ PDU settings.
Page 254 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE ............263 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:PPANtenna ...............263 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:RAONly ............264 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:RCAPability ..............264 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:RFU ..............264 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:RTYPe ..............265 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:TFCS ..............265 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:TIONe ..............265 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:TITWo ..............265 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:TPM ..............266 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:TSW ............266 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:RRSequence ............266 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:RSOunding ............
Page 255 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE Manual operation: "T_IP1_Capability Table" on page 117 [:SOURce<hw>]:BB:BTOoth:CS:CDATa[:BPOSition<ch0>]:TIPT:CAPability <TITCapability> Enables the T_IP2 capability including the T_IP2 time per bit position. Suffix: BPOSition<ch0> 0 to 7 Bit position (optional suffix) Parameters: <TITCapability>...
Page 256 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:CS:CDATa:ACI <ACI> Sets the antenna configuration index (ACI) field. The value has a length of 1 octet or 0 to 7 in decimal representation. Parameters: <ACI> ACI0 | ACI1 | ACI2 | ACI3 | ACI4 | ACI5 | ACI6 | ACI7 *RST: ACI0 Example:...
Page 257 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE Manual operation: "Config_ID" on page 119 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:CSAThreec <CsaThreec> Enables the channel selection algorithm #3c. Parameters: <CsaThreec> 1 | ON | 0 | OFF *RST: Example: Example"To configure CS control PDUs" on page 251.
Page 258 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE Example: Example"To configure CS control PDUs" on page 251. Manual operation: "Offset" on page 127 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:MAPath <MaxAntPath> Sets the maximum Num_Ant paths. Parameters: <MaxAntPath> integer Range: 1 to 4 *RST: Example: Example"To configure CS control PDUs"...
Page 259 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE Parameters: <MainMode> MODE1 | MODE2 | MODE3 For a description, see [:SOURce<hw>]:BB:BTOoth:CS[: on page 196. SEVent<ch0>]:MMODe *RST: MODE1 Example: Example"To configure CS control PDUs" on page 251. Manual operation: "Main_Mode"...
Page 260 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:CS:CDATa:MTYPe? Queries the CS LL control packet mode type that is Mode-3. Return values: <ModeType> MODE3 *RST: MODE3 Example: Example"To configure CS control PDUs" on page 251. Usage: Query only Manual operation: "Mode_Types"...
Page 261 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:CS:CDATa:NFAE <NoFae> Sets the No_FAE bit. This bit indicates if the transmitting LE device supports a frac- tional frequency offset actuation error (FAE) or not. Parameters: <NoFae> 1 | ON | 0 | OFF 1|ON The transmitting LE device only supports an FAE of zero.
Page 262 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:CS:CDATa:OMAX <OffsetMax> Sets the time value of the Offset_Max field. The value has a length of 3 octets or 9 bits. Parameters: <OffsetMax> integer Range: 500 to 16777215 *RST: Example: Example"To configure CS control PDUs"...
Page 263 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:CS:CDATa:PHY? Queries the PHY field value. This value indicates the TX PHY of the remote device to which the Pwr_Delta field in this PDU applies. Return values: <Phy> L1M | L2M | LCOD | L2M2B For a description, see [:SOURce<hw>]:BB:BTOoth:PFORmat on page 177.
Page 264 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE :SOURce1:BB:BTOoth:CS:CDATa:RCAPability See also the table Table 5-9 for an overview. Parameters: <RttAaOnly> AR150 | AR10 | AR0 *RST: AR150 Example: Example"To configure CS control PDUs" on page 251. Manual operation: "RTT_AA_Only"...
Page 265 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE Manual operation: "RTT_Type" on page 121 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:TFCS <TFcs> Sets the frequency change period (T_FCS) between consecutive CS steps. The period ranges from 15 μs to 150 μs. Parameters: <TFcs> TFCS_15 | TFCS_20 | TFCS_30 | TFCS_40 | TFCS_50 | TFCS_60 | TFCS_80 | TFCS_100 | TFCS_120 | TFCS_150 TFCS_x, x represents values in microseconds.
Page 266 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE Parameters: <TPM> TPM_10 | TPM_20 | TPM_40 | TPM_652 TPM_x, x represents values in microseconds. *RST: TPM_40 Example: Example"To configure CS control PDUs" on page 251. Manual operation: "T_PM" on page 122 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:TSW <Tsw>...
Page 267 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE Parameters: <RSOunding> AR150 | AR10 | AR0 *RST: AR150 Example: Example"To configure CS control PDUs" on page 251. Manual operation: "RTT_Sounding_N" on page 115 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:SINTerval <SubInterval> Sets or queries the subevent interval. Setting requires BB:BTOoth:CS:SNUMber 2 or higher.
Page 268 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - LE Manual operation: "Subevent_Per_Event" on page 124 "Subevents_Per_Event" on page 127 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:SPEStimate <SPEstimate> Sets the Sounding_PCT_Estimate bit. This bit indicates if the device supports phase correction term (PCT) estimates from a sounding sequence or not. Parameters: <SPEstimate>...
Page 269: Test Packet Configuration Commands - Le
® Remote control commands R&S SMW-K60/-K117/-K178 Test packet configuration commands - LE 8.7 Test packet configuration commands - LE Example: To configure test packets // ***************************************************************************** // Configure settings of an LE uncoded PHY test packet. // ***************************************************************************** // Set for a data channel test packet in the LE uncoded PHY. SOURce1:BB:BTOoth:CTYPe DATA SOURce1:BB:BTOoth:UPTYpe TPAC SOURce1:BB:BTOoth:PFORmat L1M...
Page 270 ® Remote control commands R&S SMW-K60/-K117/-K178 Test packet configuration commands - LE Parameters: <SPB> TWO | EIGHt *RST: Example: Example"To configure test packets" on page 269. Options: R&S SMW-K117 Manual operation: "Symbols per a Bit" on page 130 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SYNCword <syncWord> Sets the 32-bit Sync Word in the packet header field in hexadecimal representation.
Page 271 ® Remote control commands R&S SMW-K60/-K117/-K178 Test packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:DTTest:TPConfiguration:TPINterval <TpInterval> Sets the time interval between two consecutive test packets, regarding the starting points. Command sets the values in ms. Query returns values in s. Parameters: <TpInterval> float Range: 0.625E-3 s to 27.5E-3 s - depends on packet char-...
Page 272: Channel Configuration Commands - Br/Edr
® Remote control commands R&S SMW-K60/-K117/-K178 Channel configuration commands - BR/EDR PAT6 Predefined pattern: 01010101 DLISt Binary data from data lists as a data source. Set the data list file via the following command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration: on page 232 PCONfiguration:DATA:DSELection *RST: PN09 Example: Example"To configure test packets"...
Page 273: Packet Configuration Commands - Br/Edr
® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - BR/EDR Manual operation: "Sequence Length" on page 134 [:SOURce<hw>]:BB:BTOoth:STIMing <SlotTiming> Selects the Rx slot timing mode. Parameters: <SlotTiming> TX | LOOPback *RST: Example: BB:BTO:PTYP DH3 sets the packet type. BB:BTO:STIM LOOP selects loopback test mode.
Page 274 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - BR/EDR [:SOURce<hw>]:BB:BTOoth:PCONfiguration:ACKNowledgement <Acknowledgement> Sets the ARQN bit of the packet header.. Parameters: <Acknowledgement> NAK | ACK Request to retransmit the previous payload. Previous payload has been received successfully. *RST: Example: BB:BTO:PTYP DH1 selects the packet type DH1.
Page 275 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - BR/EDR <BitCount> integer Range: 16 to 16 *RST: Example: BB:BTO:PCON:BDAN #H0000,16 Sets the non-significant address part. Manual operation: "Bluetooth Device Address (BD_ADDR)" on page 137 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:BDAUap <BdaUap>, <BitCount> Enters the upper address part of Bluetooth Device Address. The length of UAP is 8 bits or 2 hexadecimal figures.
Page 276 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - BR/EDR [:SOURce<hw>]:BB:BTOoth:PCONfiguration:DATA <Data> Selects the data source used for the payload. Parameters: <Data> ALL0 | ALL1 | PATTern | PN09 | PN11 | PN15 | PN16 | PN20 | PN21 | PN23 | DLISt *RST: PN09 Example:...
Page 277 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - BR/EDR [:SOURce<hw>]:BB:BTOoth:PCONfiguration:DATA:VDPAttern <VdPattern>, <BitCount> Sets the bit pattern for the voice data. Parameters: <VdPattern> numeric *RST: <BitCount> integer Range: 1 to 64 *RST: Example: BB:BTO:PCON:DATA:PATT Selects the data type. BB:BTO:PCON:DATA:VDPA #B010101,6 Selects the bit pattern for the voice data with the length of 24 bits.
Page 278 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - BR/EDR [:SOURce<hw>]:BB:BTOoth:PCONfiguration:DSFPacket <DsfPacket> Selects the data source for the selected packet type. Parameters: <DsfPacket> PEDit | ADATa Enables the "Packet Editor". All packet fields can be configured individually. ADAT Fills the generated packets with the selected data source. Useful if predefined data contents are loaded with a data list file or the data contents of the packet are not of interest.
Page 279 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - BR/EDR Manual operation: "EIR packet follows" on page 139 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:HFControl <HfControl> The command sets the FLOW bit in the header. This bit indicates start or stop of trans- mission of packets over the ACL logical transport. Parameters: <HfControl>...
Page 280 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - BR/EDR Parameters: <LtAddress> integer Range: 0 to 7 Increment: 1 *RST: Example: BB:BTO:PCON:PTYP DH1 sets the packet type. BB:BTO:PCON:DSFP PED enable packet editor under data source for packet BB:BTO:PCON:LTAD 0 sets the logical transport address equal zero.
Page 281 ® Remote control commands R&S SMW-K60/-K117/-K178 Packet configuration commands - BR/EDR Example: BB:BTO:PCON:DSFP ADAT fills the all data under data source for packet. BB:BTO:PCON:PLEN 1 sets the packet length. Manual operation: "Packet Length" on page 142 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:SLAP <State> Activates synchronization of the lower address part (LAP) of the sync word and Blue- tooth device address.
Page 282: Filter/Clipping Commands
® Remote control commands R&S SMW-K60/-K117/-K178 Filter/clipping commands The scan interval is equal to the scan window T w page scan (continuous nscan) and maximal 1.28s. The scan interval is maximal 1.28s. The scan interval is maximal 2.56s. *RST: Example: BB:BTO:PCON:PTYP FHS sets the packet type.
Page 283 ® Remote control commands R&S SMW-K60/-K117/-K178 Filter/clipping commands .............287 [:SOURce<hw>]:BB:BTOoth:FILTer:PARameter:GAUSs ............288 [:SOURce<hw>]:BB:BTOoth:FILTer:PARameter:LPASs ............288 [:SOURce<hw>]:BB:BTOoth:FILTer:PARameter:PGAuss ..........288 [:SOURce<hw>]:BB:BTOoth:FILTer:PARameter:RCOSine ............289 [:SOURce<hw>]:BB:BTOoth:FILTer:PARameter:SPHase ..............289 [:SOURce<hw>]:BB:BTOoth:SRATe:VARiation [:SOURce<hw>]:BB:BTOoth:CLIPping:LEVel <Level> Sets the limit for level clipping. This value indicates at what point the signal is clipped. It is specified as a percentage, relative to the highest level.
Page 284 ® Remote control commands R&S SMW-K60/-K117/-K178 Filter/clipping commands Parameters: <State> 1 | ON | 0 | OFF *RST: Example: SOURce1:BB:BTO:CLIP:STAT ON Activates level clipping. Manual operation: "Filter/Clipping" on page 37 "State" on page 148 [:SOURce<hw>]:BB:BTOoth:FILTer:FILTers? Queries all configured baseband filters. These filters are the common GFSK baseband filter and, for some EDR packets, a DPSK filter.
Page 285 ® Remote control commands R&S SMW-K60/-K117/-K178 Filter/clipping commands [:SOURce<hw>]:BB:BTOoth:FILTer:ILENgth <ILength> Sets the impulse length (the number of filter taps). Parameters: <ILength> integer Range: 1 to depends on oversampling *RST: Example: SOURce1:BB:BTO:FILT:ILEN 10 Sets the number of filter tabs to 10. Manual operation: "Impulse Length"...
Page 286 ® Remote control commands R&S SMW-K60/-K117/-K178 Filter/clipping commands Example: SOURce1:BB:BTO:FILT:OSAM:AUTO ON The most sensible parameters are selected automatically. Manual operation: "Oversampling" on page 145 [:SOURce<hw>]:BB:BTOoth:FILTer:MINDex <MIndex> Queries the modulation index resulting from the entered frequency deviation value. Parameters: <MIndex> string Example: SOURce1:BB:BTO:FILT:MIND? Queries the modulation index...
Page 287 ® Remote control commands R&S SMW-K60/-K117/-K178 Filter/clipping commands Parameters: <Apco25> float Range: 0.05 to 0.99 Increment: 0.01 *RST: Example: SOURce1:BB:BTO:FILT:PAR:APCO25 0.2 Sets the roll-off factor to 0.2 for filter type APCO25. Manual operation: "B*T" on page 144 "Roll Off Factor/B*T" on page 146 [:SOURce<hw>]:BB:BTOoth:FILTer:PARameter:COSine <Cosine>...
Page 288 ® Remote control commands R&S SMW-K60/-K117/-K178 Filter/clipping commands Parameters: <Gauss> float Range: 0.15 to 2.5 Increment: 0.01 *RST: Example: SOURce1:BB:BTO:FILT:PAR:GAUS 0.5 Sets B x T to 0.5 for the Gauss filter type for π/4 DQPSK or 8DPSK sections. Manual operation: "B*T"...
Page 289: Power Ramping Commands
® Remote control commands R&S SMW-K60/-K117/-K178 Power ramping commands Parameters: <RCosine> float Range: 0 to 1 Increment: 0.01 *RST: Example: SOURce1:BB:BTO:FILT:PAR:RCOS 0.22 Sets the roll-off factor to 0.22 for filter type Root Cosine. Manual operation: "B*T" on page 144 "Roll Off Factor/B*T" on page 146 [:SOURce<hw>]:BB:BTOoth:FILTer:PARameter:SPHase <SPhase>...
Page 290 ® Remote control commands R&S SMW-K60/-K117/-K178 Power ramping commands [:SOURce<hw>]:BB:BTOoth:PRAMping:FOFFset <FOffset> Sets the offset of the falling edge of a burst. The offset is specified by the selected number of symbols. Negative values shift the falling edge to earlier positions, which results in a correspond- ing number of skipped symbols at the end of the burst.
Page 291: Trigger Commands
® Remote control commands R&S SMW-K60/-K117/-K178 Trigger commands Example: BB:BTO:PRAM:ROFF 8 Skips eight symbols at the beginning of the burst. Manual operation: "Rise Offset" on page 150 [:SOURce<hw>]:BB:BTOoth:PRAMping:RTIMe <RTime> Sets the ramp time, which extends the burst by a corresponding number of 0 padding symbols at the beginning and the end of a burst.
Page 292 ® Remote control commands R&S SMW-K60/-K117/-K178 Trigger commands Example: To configure an internal trigger // ****************************************************************** // Configure trigger in single mode. // Set source to internal, specify signal duration // unit and duration. // ****************************************************************** SOURce1:BB:BTOoth:TRIGger:SEQuence SING SOURce1:BB:BTOoth:TRIGger:SOURce INT SOURce1:BB:BTOoth:TRIGger:SLUNit SEQ SOURce1:BB:BTOoth:TRIGger:SLUNit FRAMe SOURce1:BB:BTOoth:TRIGger:SLENgth 2...
Page 293 ® Remote control commands R&S SMW-K60/-K117/-K178 Trigger commands ..........297 [:SOURce<hw>]:BB:BTOoth:TRIGger:OBASeband:INHibit ............297 [:SOURce<hw>]:BB:BTOoth:TRIGger[:EXTernal]:DELay ............297 [:SOURce<hw>]:BB:BTOoth:TRIGger[:EXTernal]:INHibit [:SOURce<hw>]:BB:BTOoth[:TRIGger]:SEQuence <Sequence> Selects the trigger mode: ● AUTO = auto ● RETRigger = retrigger ● AAUTo = armed auto ● ARETrigger = armed retrigger ● SINGle = single Parameters: <Sequence>...
Page 294 ® Remote control commands R&S SMW-K60/-K117/-K178 Trigger commands Example: Example"To configure an external trigger" on page 291. Example: Example"To configure an internal trigger" on page 292. Options: ELTRigger|ELCLock require R&S SMW-B10 BBSY require R&S SMW-B9 Manual operation: "Source" on page 154 [:SOURce<hw>]:BB:BTOoth:TRIGger:RMODe <RMode>...
Page 295 ® Remote control commands R&S SMW-K60/-K117/-K178 Trigger commands <DigStd> is the mnemonic for the digital standard, for example, ARB. Time-based trig- gering behaves analogously for all digital standards that support this feature. Parameters: <Time> string Example: See example "Configure a time-based trigger signal" in the sub- chapter "Trigger Commands"...
Page 296 ® Remote control commands R&S SMW-K60/-K117/-K178 Trigger commands [:SOURce<hw>]:BB:BTOoth:TRIGger:SLUNit <SlUnit> Defines the unit for the entry of the signal sequence length. Parameters: <SlUnit> FRAMe | SEQuence | EVENt FRAMe A single frame is generated after a trigger event. SEQuence A single sequence is generated after a trigger event. *RST: SEQuence Example:...
Page 297 ® Remote control commands R&S SMW-K60/-K117/-K178 Trigger commands Parameters: <Delay> float Range: 0 to 2147483647 Increment: 0.01 *RST: Example: Example"To configure an internal trigger" on page 292. Manual operation: "External Delay/Trigger Delay" on page 156 [:SOURce<hw>]:BB:BTOoth:TRIGger:OBASeband:INHibit <Inhibit> For triggering via the other path, specifies the duration by which a restart is inhibited. Parameters: <Inhibit>...
Page 298: Marker Commands
® Remote control commands R&S SMW-K60/-K117/-K178 Marker commands 8.13 Marker commands Example: To configure a marker signal // ****************************************************************** // Configure marker mode: set a marker at ARB sequence start. // ****************************************************************** SOURce1:BB:BTOoth:TRIGger:OUTPut1:MODE RESTart // SOURce1:BB:BTOoth:TRIGger:OUTPut1:MODE STARt // SOURce1:BB:BTOoth:TRIGger:OUTPut1:MODE ACTive // ****************************************************************** // Alternatively configure pulse marker.
Page 299 ® Remote control commands R&S SMW-K60/-K117/-K178 Marker commands [:SOURce<hw>]:BB:BTOoth:TRIGger:OUTPut<ch>:DELay <Delay> Defines the delay between the signal on the marker outputs and the start of the sig- nals. Parameters: <Delay> float Range: 0 to 16777215 Increment: 0.001 *RST: Example: Example"To configure marker delay" on page 298.
Page 300 ® Remote control commands R&S SMW-K60/-K117/-K178 Marker commands PULSe A regular marker signal is generated. The clock frequency is defined by entering a divider. The frequency is derived by divid- ing the symbol rate by the divider. The input box for divider opens when "Pulse"...
Page 301 ® Remote control commands R&S SMW-K60/-K117/-K178 Marker commands Parameters: <Pattern> numeric *RST: <BitCount> integer Range: 1 to 64 *RST: Example: Example"To configure a marker signal" on page 298. Manual operation: "Mode" on page 157 [:SOURce<hw>]:BB:BTOoth:TRIGger:OUTPut<ch>:PINDex <PIndex> For Bluetooth LE data packets higher than one, sets the packet index. The index corre- sponds to the transmitted Tx event during the connection interval.
Page 302: Clock Commands
® Remote control commands R&S SMW-K60/-K117/-K178 Clock commands Example: Example"To configure a marker signal" on page 298. Usage: Query only Manual operation: "Mode" on page 157 [:SOURce<hw>]:BB:BTOoth:TRIGger:OUTPut<ch>:RESHift <Shift> Shifts the rising edge of the marker the specified number of samples. Negative values result in a shift back of the marker edge.
Page 303 ® Remote control commands R&S SMW-K60/-K117/-K178 Clock commands Example: Example"To configure clock settings" on page 302. Options: R&S SMW-B10 Manual operation: "Clock Mode" on page 160 [:SOURce<hw>]:BB:BTOoth:CLOCk:SOURce <Source> Selects the clock source: ● INTernal: Internal clock reference ● ELCLock: External local clock ●...
Page 304: Glossary: Specifications
® Glossary: Specifications R&S SMW-K60/-K117/-K178 Glossary: Specifications Symbols [1]: Bluetooth SIG: Bluetooth Core Specification, version 5.4 https://www.bluetooth.com/specifications/specs/ [2]: Bluetooth SIG: Channel Sounding, revision CR_PR https://www.bluetooth.com/specifications/specs/ User Manual 1175.6803.02 ─ 26...
Page 305: List Of Commands
® List of commands R&S SMW-K60/-K117/-K178 List of commands [:SOURce<hw>]:BB:BTOoth:BCRole......................175 [:SOURce<hw>]:BB:BTOoth:BCText?......................164 [:SOURce<hw>]:BB:BTOoth:BMODe......................164 [:SOURce<hw>]:BB:BTOoth:CCRC:STATe....................176 [:SOURce<hw>]:BB:BTOoth:CLIPping:LEVel....................283 [:SOURce<hw>]:BB:BTOoth:CLIPping:MODE....................283 [:SOURce<hw>]:BB:BTOoth:CLIPping:STATe....................283 [:SOURce<hw>]:BB:BTOoth:CLOCk:MODE....................302 [:SOURce<hw>]:BB:BTOoth:CLOCk:SOURce....................303 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:ACI....................256 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:CCID:STATe...................256 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:CECount..................256 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:CID....................256 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:CSAThreec..................257 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:CSIGnal..................257 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:CSPCapability?................268 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:ECODe..................257 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:EOFFset..................257 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:MAPath..................258 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:MMASteps..................
Page 306 ® List of commands R&S SMW-K60/-K117/-K178 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:SMODe..................268 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:SNUMber..................267 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:SPEStimate................... 268 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:TFCS..................... 265 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:TIONe.................... 265 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:TITWo.................... 265 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:TPM....................265 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:TSW....................266 [:SOURce<hw>]:BB:BTOoth:CS:CDATa[:BPOSition<ch0>]:TFCapability.............254 [:SOURce<hw>]:BB:BTOoth:CS:CDATa[:BPOSition<ch0>]:TIPO:CAPability..........254 [:SOURce<hw>]:BB:BTOoth:CS:CDATa[:BPOSition<ch0>]:TIPT:CAPability..........255 [:SOURce<hw>]:BB:BTOoth:CS:CDATa[:BPOSition<ch0>]:TPCapability.............255 [:SOURce<hw>]:BB:BTOoth:CS:CDATa[:CHANnel<ch0>]:CFAE..............255 [:SOURce<hw>]:BB:BTOoth:CS:CFCHm?....................209 [:SOURce<hw>]:BB:BTOoth:CS:CINC......................208 [:SOURce<hw>]:BB:BTOoth:CS:CINP......................208 [:SOURce<hw>]:BB:BTOoth:CS:CINTerval....................191 [:SOURce<hw>]:BB:BTOoth:CS:CIVC......................207 [:SOURce<hw>]:BB:BTOoth:CS:CIVP......................207 [:SOURce<hw>]:BB:BTOoth:CS:CMRepetition..................... 210 [:SOURce<hw>]:BB:BTOoth:CS:CPVP......................
Page 307 ® List of commands R&S SMW-K60/-K117/-K178 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:MTWO:TPM..............199 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:MTWO:TSW?..............199 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:MZERo:TIPO..............198 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:MZSTeps................195 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:NOSTep................194 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:PATTern................205 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:SEQLength............... 200 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:SMODe................197 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:SMSTep?................198 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:SSPace?................195 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:STYPe................200 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:TFCS................195 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:UPAYload................200 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:UPPattern................. 201 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>][:STEP<st0>]:CAADdress..........203 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>][:STEP<st0>]:CINDex............203 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>][:STEP<st0>]:CSIGnal............204 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>][:STEP<st0>]:CTEXtension..........205 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>][:STEP<st0>]:MTYPe?............202 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>][:STEP<st0>]:SCONtent............ 203 [:SOURce<hw>]:BB:BTOoth:CTYPe......................176 [:SOURce<hw>]:BB:BTOoth:DCYCle......................176 [:SOURce<hw>]:BB:BTOoth:DTTest:DTTState.....................
Page 308 ® List of commands R&S SMW-K60/-K117/-K178 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:LTKey..................185 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:AADDress............218 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ACAD............224 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ACAD:APATtern.......... 224 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ACAD:ASELection........225 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ACASsigned..........225 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ACID............225 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ADID............226 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ALAP............226 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ALENgth............227 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:AMODe............227 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ANUap............227 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:AOFFset............228 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:AOUNits............228 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:APHY............228 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ASID............229 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ATYPe............248 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CACCuracy..........229 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CECount............248 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CID.............. 230 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CINStant............230 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CINTerval.............230 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CIValue............218 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CPResent............
Page 309 ® List of commands R&S SMW-K60/-K117/-K178 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ID..............249 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ILAP.............226 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:INUap............227 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:LCTimeout........... 237 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:LPECounter..........249 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MCLReq............249 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MIVector............237 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MNINterval..........185 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MROCtets............238 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MRTime............239 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MSKD............238 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MTOCtets............ 238 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MTSPhy:L1M:STATe........239 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MTSPhy:L2M:STATe........239 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MTSPhy:LCOD:STATe........ 239 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MTTime............239 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MUCHannels..........239 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MXINterval...........185 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:NCINterval...........240 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:NLCTimeout..........240 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:NSLatency...........241 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:NSValue............
Page 310 ® List of commands R&S SMW-K60/-K117/-K178 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SNUap............227 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SOUNits............245 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SPBit............269 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SPOFfset.............246 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SSKD............238 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SSValue............219 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:STMPhy:L1M:STATe........239 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:STMPhy:L2M:STATe........239 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:STMPhy:LCOD:STATe........ 239 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SVNumber...........246 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SYNCword...........270 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:TATYpe............242 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:TLAP............226 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:TNUap............227 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:TPHYs:L1M:STATe........243 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:TPHYs:L2M:STATe........244 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:TPHYs:LCOD:STATe........244 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:TPOWer............246 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:USERpatt............ 270 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:UTYPe............247 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:VNUMber.............247 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:WOFFset............. 247 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:WSIZe............248 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PNUMber................188 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:SDCI?..................
Page 311 ® List of commands R&S SMW-K60/-K117/-K178 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:BDAUap.................275 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:CODevice................275 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:DATA..................276 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:DATA:DPATtern..............276 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:DATA:DSELection..............276 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:DATA:VDPAttern..............277 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:DATA:VDSElection..............277 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:DLENgth................277 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:DSFPacket................278 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:DWHitening................278 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:EIRPacketfollows..............278 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:HFControl................279 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:LFSWord................279 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:LTADdress................279 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:PFControl................280 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:PLENgth................280 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:SLAP..................281 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:SNSValue................281 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:SRMode.................281 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:VDATa..................282 [:SOURce<hw>]:BB:BTOoth:PFORmat......................177 [:SOURce<hw>]:BB:BTOoth:PRAMping:FOFFset..................
Page 312 ® List of commands R&S SMW-K60/-K117/-K178 [:SOURce<hw>]:BB:BTOoth:TRIGger:RMODe..................... 294 [:SOURce<hw>]:BB:BTOoth:TRIGger:SLENgth....................295 [:SOURce<hw>]:BB:BTOoth:TRIGger:SLUNit....................296 [:SOURce<hw>]:BB:BTOoth:TRIGger:SOURce....................293 [:SOURce<hw>]:BB:BTOoth:TRIGger:TIME:DATE..................294 [:SOURce<hw>]:BB:BTOoth:TRIGger:TIME:TIME..................294 [:SOURce<hw>]:BB:BTOoth:TRIGger:TIME[:STATe]..................295 [:SOURce<hw>]:BB:BTOoth:TRIGger[:EXTernal]:DELay................297 [:SOURce<hw>]:BB:BTOoth:TRIGger[:EXTernal]:INHibit................297 [:SOURce<hw>]:BB:BTOoth:TRIGger[:EXTernal]:SYNChronize:OUTPut.............296 [:SOURce<hw>]:BB:BTOoth:UNIT:TIME....................... 167 [:SOURce<hw>]:BB:BTOoth:UPTYpe......................177 [:SOURce<hw>]:BB:BTOoth:USLength......................179 [:SOURce<hw>]:BB:BTOoth:VERSion?......................167 [:SOURce<hw>]:BB:BTOoth:WAVeform:CREate..................167 [:SOURce<hw>]:BB:BTOoth[:TRIGger]:SEQuence..................293 User Manual 1175.6803.02 ─ 26...
Page 313: Index
® Index R&S SMW-K60/-K117/-K178 Index Advertising packet configuration ......... 58 Angle of arrival ............21 Access address ..............59 Angle of departure ............22 ACK ................. 138 Data packet configuration ........... 58 Acknowledgment ............. 138 Direction finding ............21 ACL+EDR ................37 Settings ...............
Page 314 ® Index R&S SMW-K60/-K117/-K178 Controller role Submode ..............101 Advertiser ..............48 Submode CS steps ........... 101 Central ................ 48 T_FCS ..............122 Peripheral ..............48 T_IP2 ................ 122 Scanner ..............48 T_PM ................ 122 Conventions CS step info SCPI commands ............161 CS step table ............
Page 315 ® Index R&S SMW-K60/-K117/-K178 Event active part Marker ............... 157 Event configuration LAP ................. 137 Channel table .............. 57 LAP for sync word ............136 Level Event inactive part Marker ............... 157 Clipping ..............148 LL connection event count ..........82 Event start Marker ...............
Page 316 ® Index R&S SMW-K60/-K117/-K178 Data whitening ............ 59, 136 Remote control Device address ............137 Programming examples ..........161 EIR packet follows ............ 139 Restart Encrypted DIVersifier(hex) .......... 82 Marker ............... 157 Error code ..............82 Retrigger FeatureSet length ............83 Trigger mode .............152 Flow control (header) ..........
Page 317 ® Index R&S SMW-K60/-K117/-K178 Subevent CS step configuration ..........94 CS step info ..............94 Version Frequency change period ........... 94 Bluetooth ..............37 Version number ..............83 Interval ................ 92 Length ................. 92 Videos ................12 Mode-0 steps .............. 94 Number ...............

This manual is also suitable for:

R&s smw-k117 R&s smw-k178

Rohde & Schwarz R&S SMW-K60 User Manual

Table of Contents

Bluetooth General Settings

Settings: Adva/Targeta

Quick Links

Chapters

Need help?

Questions and answers

Related Manuals for Rohde & Schwarz R&S SMW-K60

Summary of Contents for Rohde & Schwarz R&S SMW-K60

This manual is also suitable for:

Table of Contents