Related Manuals for NEFF D99W6N0GB
Summary of Contents for NEFF D99W6N0GB
- Page 1 Installation instructions and how to use and look after your built-in cooker hoods D99W6N0 NEFF (UK) Ltd...
- Page 2 Fig. 1 Abb. 1 ELECTRO...
-
Page 3: Operating Modes
filter and activated carbon filter of the same chimney (such as gas, oil or and then conveyed back into the coal-fired heaters, continuous-flow heaters, kitchen. -
Page 4: Before Using For The First Time
Use carefully. They contain important The manufacturer of the extractor information concerning your personal hoods accepts no liability for complaints safety as well as on use and care of the which can be attributed to the design appliance. and layout of the pipework. -
Page 5: Safety Instructions
fire. (max. 15 minutes) at maximum thermal If you are cooking with fat or oil, e.g. chips, load, otherwise there is a risk of burns from etc., never leave the cooker unattended. touching the housing surfaces or a risk of damaging the extractor hood. -
Page 6: Operating Procedure
Setting the required fan speed: Switch the ventilator OFF Press the + button. a few minutes after you have finished The fan speed is increased by one step. cooking. Press the – button. Set the glass plate in cooking The fan speed is reduced by one step. -
Page 7: Filters And Maintenance
Important: By cleaning the metal grease filters at appropriate intervals, the possibility of them catching fire as a result of a build-up of heat such as occurs when deep-fat frying or roasting is taking place, is reduced. 2. Clean the filter. - Page 8 As the filter becomes more and more grease filter"). saturated with grease, there is an increased 2. Insert the activated carbon filter. risk of fire and the function of the extractor hood may be impaired. Important: Change the activated carbon filter promptly to prevent the risk of fire from the...
-
Page 9: Cleaning And Care
20 Watt, G4 cap). Stainless steel surfaces: Caution: Refer for plug-in lampholder. Use a mild non-abrasive stainless steel Take hold of the bulb with a clean cloth. cleaner. Clean the surface in the same direction as it has been ground and polished. -
Page 10: Installation Instructions
Only one side of the extractor hood Please ask your dealer or inquire at your may be installed next to a high-sided unit local authority about current means of or high wall. Gap at least 50 mm. -
Page 11: Prior To Installation
flue that is interlocking, etc. currently used for other purposes, nor into a shaft that is used for ventilating rooms in If the air intake is inadequate, there is a which stoves or fireplaces are also located. -
Page 12: Circulating-Air Mode
Connecting a l 150 mm exhaust-air pipe: Short, smooth air exhaust pipe. Mount the pipe As few bends in the pipe as possible. directly onto the Diameter of pipe to be as large as air outlet on the possible and no tight bends in pipe. -
Page 13: Electrical Connection
23,5 25,0 A separator must be installed in the We reserve the right to construction changes within the household circuit. A suitable separator is a context of technical development. switch that has a contact gap of more than 3 mm and interrupts all poles. -
Page 14: Installation
4. Drill 4 x l 8 mm holes for the extractor hood and 2 x l 8 mm holes for the chimney panelling. Insert plugs into the holes so that they are flush with the wall. - Page 15 Installation 07. Screw in lower screws (hex screws). 13. Insert the cover panels at an angle and tilt them back. 08. Stick protective film over the holes of The bottom panel must snap in the the 2 lower mounting bolts in the bolts at the back.
- Page 16 Z 5116X5 360732 NEFF (UK) Ltd. Grand Union House, Old Wolverton Road, Old Wolverton Milton Keynes, MK12 5PT Tel: 01908 328300 9000 227 443 Fax: 01908 328399 Printed in Germany 0507 Es.