CyberPower HT706UC - SURGE PROTECTOR Manual

Also See for HT706UC:

User manual (2 pages)

Table of Contents

Contents

1 FEATURES
2 SPECIFICATIONS
3 TROUBLESHOOTING
4 FOR MORE INFORMATION
5 CAUTION
6 Documents / Resources
- 6.1 References
- 6.2 Download manual

CyberPower HT706UC - SURGE PROTECTOR Manual

FEATURES

ON/OFF Reset Control Switch and Circuit Breaker
Controls power to all outlets. The switch is also a 15A breaker. When an overload occurs, it will automatically switch off. To resume operation, ensure the overload condition is removed and reset the surge protector by switching the unit ON.
Firestop Design Advanced Metal-Oxide Varistor (MOV) with Built-In Fuses
Encased component dissipates surge events and potential flame, sparks and heat.
Wrapped Cord and Right Angle Plug
Easy to coil. Kink and abrasion-resistant cord with low-profile right-angle plug for easy cord management.
Advanced Protection - Surge Protected LED
Illuminated when protection is working properly.
Clean Power - Ground LED
Illuminated when properly grounded.
Seven Outlets
6 standard and 1 transformer spaced outlets
USB Charging Ports*
Connect and charge up to 2 USB devices using the surge protected USB charging ports. *USB outlets cannot be used as a USB hub. This device does not transfer data.
Coaxial Cable Protection
Protects coaxial lines from surges and spikes.

SPECIFICATIONS

Model Number:	HT706UC
Outlets:	6 standard and 1 transformer spaced outlets
USB Charging Rating:	5V / 4.8A total
Power Cord Length:	5 ft
Surge Protection:	2280 Joules
Electrical Rating:	125V / 15A / 1875W
UL Clamping Voltage:	UL 1449 3rd 500V (L-N, L-G, L-G)
Maximum Peak Current:	75,000A
3 AC Lines Protected:	H-N: 45,000A, H-G: 15,000A, N-G: 15,000A (The maximum surge possible on household wiring is 6,000 volts)
Response Time:	Less than 1 nanosecond
Attenuation:	Up to 43dB
EMI/RFI Filtration:	150 kHz to 100 MHz
Circuit Breaker:	Resettable 15 Amp

This product can expose you to chemicals including bisphenol A (BPA) and styrene (ABS), which is known to the State of California to cause reproductive harm and cancer. For more information, go to www.P65Warnings.ca.gov.

TROUBLESHOOTING

If the grounded indicator does not light when you plug in the surge protector, move the surge protector to a different grounded three-prong AC outlet. If it still does not light, return the product to the dealer for assistance.

If the surge protector proves to be working properly, your outlets may not be a properly grounded and need to be repaired by a professional electrician. If the grounded indicator turns off after a period of use, the surge protection has been depleted. Replace your surge protector. If the protected indicator does not light, the surge protector's AC lines is no longer protected from surge. The surge protector may have received a power surge or spike beyond its specified limits that overloaded the protection circuitry and rendered it inactive. The surge protector has protected your connected equipment as designed, but it will not protect against future surges, and spikes. It should be replaced.

FOR MORE INFORMATION

Visit CyberPowerSystems.com for more information regarding:

Product information and certifications
Product warranty
Connected equipment guarantee

CAUTION

TO REDUCE THE RISK OF ELECTRIC SHOCK:

Use only in dry locations and only indoors.
DO NOT plug into another relocatable power tap.
DO NOT "daisy chain" surge protectors.
DO NOT use with any aquarium equipment.
DO NOT use if properly grounded outlets are not available.
DO NOT install this device if there is less than 10 meters (30 feet) of wire between the electrical outlet and electrical service panel.
DO NOT use for medical or life support equipment. This device features an internal protection that will disconnect the surge protective component at the end of its useful life, but it will maintain unprotected power to the load.