1. Manuals
  2. Brands
  3. BendPak Manuals
  4. Lifting Systems
  5. HD-7500BLX
  6. Installation and operation manual

BendPak HD-7500BLX Installation And Operation Manual

Vehicle and boat storage four-post lift
Hide thumbs Also See for HD-7500BLX:
Table of Contents

Advertisement

Quick Links

Download this manual
Vehicle and Boat Storage Four-Post Lift
Installation and Operation Manual
Models:
• HD-7500BLX
• HD-75BXT
• HD-7500PBX
Original instructions in
the English language.
Designed and engineered by BendPak Inc. in Southern California, USA. Made in China.
I
S
MPORTANT
AFETY
of this manual before using this product. Failure to follow the instructions and safety precautions in this
manual can result in serious injury or death. Make sure all other operators also read this manual. Keep the
manual near the product for future reference.
that you fully understand the contents of this manual and assume full responsibility for
.
product use
Manual P/N 5900174 — Manual Revision D — March 2024
⚠
I
, S
NSTRUCTIONS
AVE
HD-75BXT shown above
DANGER
T
I
NSTRUCTIONS !
HESE
By proceeding with setup and operation, you agree
30440 Agoura Road.
Agoura Hills, CA 91301 USA
Toll Free: (800) 253-2363
Telephone: (805) 933-9970
bendpak.com
Read the entire contents

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HD-7500BLX and is the answer not in the manual?

Questions and answers

Related Manuals for BendPak HD-7500BLX

Summary of Contents for BendPak HD-7500BLX

  • Page 1 • HD-7500BLX • HD-75BXT • HD-7500PBX HD-75BXT shown above Original instructions in the English language. ⚠ Designed and engineered by BendPak Inc. in Southern California, USA. Made in China. DANGER Read the entire contents NSTRUCTIONS ! MPORTANT AFETY NSTRUCTIONS HESE of this manual before using this product.
  • Page 2 Copyright. Copyright © 2024 by BendPak Inc. All rights reserved. You may make copies of this document if you agree that: you will give full attribution to BendPak Inc., you will not make changes to the content, you do not gain any rights to this content, and you will not use the copies for commercial purposes.
  • Page 3 • Only use the Lift if it can be used safely! Unit Information. Enter the Model Number, Serial Number, and the Date of Manufacture from the label on your unit. This information is required for part or warranty issues. Model: Serial: Date of Manufacture:...

  • Page 4: Table Of Contents

    Introduction This manual describes the following BendPak Four-Post Lifts: HD-7500BLX: Four-Post Lift with an overall width of 133.76 in. (3,398 mm), length of 198 in. • (5,029 mm), and lifting height of 87 in. (2,210 mm). The lift is capable of raising Vehicles and Boats up to 7,500 lbs.

  • Page 5: Shipping Information

    900 chemicals identified by the State of California to cause cancer, birth defects or reproductive harm. ALWAYS use this product in accordance with BendPak’s instructions. For more information go to www.P65Warnings.ca.gov.
  • Page 6 23. Always ensure the Lift is secured on Safety Locks before working on or near a Vehicle. 24. Make a thorough inspection of the product at least once a year. Replace any damaged or severely worn parts, decals, or warning labels. Replace worn or damaged parts with BendPak or BendPak approved parts and assemblies only.
  • Page 7 32. Make an inspection of the Lift before using it. Check for damaged, worn, or missing parts. Do not use it if you find any of these issues. Instead, take it out of service, then contact an authorized repair facility, your dealer, or BendPak at (800) 253-2363, select option 7 then 4, or support@BendPak.com.

  • Page 8: Components

    Components HD-7500BLX HD-75BXT HD-7500PBX Drawings not to scale. Components removed for clarity. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 9 Ladder. A steel assembly with openings designed to engage the safety locks. Installed inside • each post. • Stiffeners. The HD-7500PBX includes stiffeners mounted between the Posts to provide additional support. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...

  • Page 10: Specifications

    Specifications P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 11 Chalk Lines for the Lift Installation, but the additional clearance is required around all four Posts. ³ The Safety Ladder adjustment adds an additional 3.25 inches max. to the Post height. Specifications subject to change without notice. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 12 Safety Locks. Q: Can I install my Lift outside? A: No. Your Lift is approved for indoor installation and use only. Outdoor installation is prohibited. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...

  • Page 13: Installation Checklist

    ☐ 18. Install the Runways. ☐ 19. Install the First End of the Flex Tube. ☐ 20. Extend the Piston ☐ 21. Route the Lifting Cables HD-7500BLX & HD-75BXT. ☐ 22 Route the Lifting Cables HD-7500PBX. ☐ 23. Install the Power Unit.

  • Page 14: Installation

    Only fully trained personnel should be involved in installing this equipment. Always pay attention. Use appropriate tools and lifting equipment. Stay clear of moving parts. BendPak recommends referring to the current version of the ANSI/ALI ALIS Standard Safety Requirements for Installation and Service of Automotive Lifts for more information about safely installing, using, and servicing your Lift.
  • Page 15 Rear of the Lift to safely drive Vehicles onto the Runways. Power. You need an appropriate power source for the Power Unit. • Outdoor installations. Your Lift is approved for indoor installation and use only. • P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 16 If a colored sheath comes up during drilling, stop drilling immediately. If the existing concrete floor does not meet the minimum requirements BendPak strongly recommends consulting a Concrete Specialist early in your planning process for the Lift installation.
  • Page 17 A minimum of 12-inches above the highest point on the vehicle is required to allow room to raise above the safety lock engagement. Check Clearances Around the Lift P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 18 Side view. Not to scale. Components removed for clarity. Drawing below is a top view. Not to scale. Not all components shown. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 19 Chalk Line Guides. Note: Pay careful attention to the Overall Width measurement. It is critical to keep this measurement within ± 0.125 in. / 3.2 mm. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 20 Both Crosstubes are hollow, which allows the Lifting Cables to run through them to the Posts. It is possible to install the Crosstubes incorrectly in several different ways. Take your time and install it right the first time. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 21 Slide Blocks when they are installed. There are two Slots per Crosstube Gusset, one at the top and one at the bottom. The Ladder must go through both Slots. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 22 3. Orient, then slide the Crosstube into the open ends of the two posts and slide all the way to the bottom of the posts. 4. Perform Step 2 for the second Crosstube and the remaining two Posts. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 23 Lifting Cable breaks while the Lift is not engaged on its Primary Safety Locks, the Slack Safety Lock next to the broken Lifting Cable immediately engages at the next Safety Lock position in the Ladder. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 24 Lift in danger. Not to scale. Components removed for clarity. Front and side views combined. Make sure to install each Ladder through both Slots on each Crosstube Gusset. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 25 Note: The remaining hole in the middle of the Top Cap is for the Lifting Cable, installed later. 6. Install the other three Top Caps the same manner. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 26 Do not anchor the Posts at this point. HD-7500PBX Shown below. HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts P/N 5900174 — Rev. D — March 2024...
  • Page 27 20 - M12 Hex Nuts 3. Raise the Stiffeners into position. 4. Bolt both the Stiffener and the Top Stiffener to each post. Refer to the figures below. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 28 Figure not to scale. Components removed for clarity. The Primary Safety Lock is now engaged, but the Slack Safety Lock is not. 3. Disengage the other three Slack Safety Locks as completed in Step 2. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 29 DANGER Do not continue with the installation until you have visually confirmed that all four Primary Safety Locks are engaged. If they are not engaged, the Crosstubes and P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 30 Cable Sheaves from under the Powerside Runway including the Pull Box and the Direction Sheaves. Important When you remove the Sheaves, keep all the components grouped together. They will be reinstalled at the same locations, using the same components. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 31 Power Side Runway does. The following drawing shows the correct orientation of the Runways for both Power Post locations. Not to scale. Not all components shown. Tops of Runways not shown. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 32 Do not continue with the installation until you have visually confirmed that all four Primary Safety Locks are engaged. If they are not engaged, the Runways could move or fall, possibly causing personal injury (or death), or product damage. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 33 5. Install the second Connector on the open end of the Flex Tube. 6. Let the free end of the Flex Tube hang in place for the moment. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 34 (such as a Come-Along) to extend the Piston. Be careful not to damage the Piston. 5. Reinstall the Shipping Plug onto the Return Line Port. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 35 Route the Lifting Cables HD-7500BLX / HD-75BXT Only Review the figure below providing an overview of the cable routing. For HD-7500PBX Cable routing Route the Lifting Cables HD-7500PBX View this manual in color at www.bendpak.com/car-lifts/four-post-lifts/ P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts...
  • Page 36 To Route Lifting Cables A and C HD-7500BLX & HD-75BXT: Review the following Cable List and identify each cable before beginning. HD-7500BLX HD-75BXT Cable Description Description Ø10 x 3,228 mm 5595351 Ø10 x 3,228 mm 5595351 Ø10 x 5,471 mm 5595191 Ø10 x 5,471 mm...
  • Page 37 11. With the Cables in place in the Large Window, reinstall the Twin Cable Sheave; make sure Lifting Cable A is set in the Bottom Cable Sheave, and Cable C is in the top Sheave. Components removed for clarity. Not to scale. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 38 15. After routing all four cables, verify each cable is properly routed and positioned within its Cable Sheaves and engaged in each Slack Safety Sheave P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 39 Tool) to extend the Piston; be careful not to damage the Piston. 6. Reinstall the Shipping Plug into the Return Line Connector to keep the system free of contaminants. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 40 Post past the top of the Crosstube Gusset. Important: Before re-installing any Sheave, lubricate the Pin and Bearing using a liberal amount of Red Lithium Grease. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 41 16. Route Cable C as in the figure to the right. Through the Direction Sheave and over to the Large Window in the Crosstube. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 42 Cable A is set in the Bottom Cable Sheave, and Cable C is in the top Sheave. Lubricate the Sheave Pin with red lithium grease. Power Side Platform Bottom View Platform Removed Top View P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 43 22. Routing Lifting Cables B and D is the same process as routing Lifting Cables A and C but uses the remaining two Posts and Sheaves. Refer to the drawings in the previous section and to the figures below. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 44 24. After routing all four cables, verify each cable is properly routed and positioned within its Cable Sheaves and engaged in each Slack Safety Sheave. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 45 Damage to the motor caused by water is not covered by the warranty. The Power Unit is heavy. BendPak recommends having one person hold the Power Unit while another person bolts it into place.
  • Page 46 Hydraulic Hoses and Fittings on the Lift, potentially making your new Lift inoperable. Your Lift is shipped with clean components; however, BendPak strongly recommends that you clean all Hydraulic Hoses and Fittings prior to making connections. It is better and less costly to take these extra steps now so that you do not need to take your Lift out of service later to fix issues that could have been prevented at the time of installation.
  • Page 47 Always promptly clean any Hydraulic Fluid spills. If a leak in the system is the source of the spill, lockout the Lift to prevent use until the Hydraulic System is repaired. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 48 Several power units are available. The fluid capacity of several common units are detailed below. Always refer to your actual unit for the exact capacity. Power units commonly shipped with these lifts are shown here. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 49 Back Plate and the retaining Nut. This configuration is common, but it is not required. Side view of where the Power Unit attaches to the Power Post. Power Unit not shown. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 50 Important: Ferrules should only be tightened once. When you tighten the Nut on the Threads, the Ferrule is compressed; the Ferrule should not be reused after this compression. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 51 An Air Supply (3 to 25 cfm at 50 to 150 psi max.) is required. The following drawing shows the Zero Angle Bracket and where it connects. The following figure details the Pushbutton Air Valve and its connections. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 52 Air Line. Do not attach the Return Line to the Pushbutton Air Valve by mistake. Double check to make sure you are attaching the Air Line to the Pushbutton Air Valve. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 53 20 Gallon Best 3 to 25 Min. ⚠ CAUTION Do not allow the Air Supply to exceed 150 psi; the Air Lines could burst or the Safety Locks malfunction. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 54 4. Connect the various sections of Tubing to the Air Line Tee Connectors on the Lift. Refer to the drawing above for the locations of the Tubing sections. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 55 5. Leave the Power Unit end of the Air Line hanging out of the Flex Tube for now. It will be connected to the Pushbutton Air Valve later in the installation process. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 56 Top View of Power Side Runway. Drawing not to scale. of the Return Line (coming out of Some components not shown or exaggerated for clarity. the Flex Tube). P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 57 Top view of the Power Side Runway. Drawing not to scale. the JIC end to the Straight end of the Some components not shown or exaggerated for clarity. Hydraulic Hose. 8. Securely tighten all connections. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 58 OSHA regulations and electrical codes. To connect the Lift to a power source: 1. Locate the Pigtail exiting the Electrical Box on the Power Unit. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 59 A licensed Electrician must perform all wiring. Electrical current that exceeds the motor’s full load amperage rating (FLA) may result in permanent damage to the motor. BendPak strongly recommends you not exceed the rated duty cycle of the Lift’s motor.
  • Page 60 8. To Lower the Lift, press the Pushbutton Air Valve and the Lowering Valve on the Power Unit simultaneously. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 61 Lift on a Concrete surface. If you install a Lift on asphalt or any other surface, or your Concrete or Anchor Bolts do not meet these specifications, it could lead to product damage, Vehicle damage, personal injury, or even loss of life. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 62 BendPak Lifts are supplied with installation instructions and Concrete fasteners meeting the criteria as prescribed by the current version of the American National Standard “Automotive Lifts – Safety Requirements for Construction, Testing, and Validation” ANSI/ALI ALCTV. ⚠ WARNING Use only the Anchor Bolts delivered with your Lift. If you use components from a different source, you void your warranty and compromise the safety of everyone who installs or operates the Lift.
  • Page 63 Expansion Sleeve does not press with as much force. Both result in less holding strength. 3. Vacuum each hole clean. BendPak recommends using a vacuum to clean the hole. A wire brush, hand pump, or compressed air may also be used; just make sure to thoroughly clean each hole.
  • Page 64 Gusset Covers. Yellow, Plastic Covers that are installed on top of the Crosstube Gussets. • Tire Stops. Installed at the Front of the Lift. Holds the Tires of the Vehicle in position. BendPak • recommends chocking the rear Tires, so that the Vehicle stays in place. Included with the Lift.
  • Page 65 2. Align the Covers with the openings in the Gusset, one at each end of the Crosstube, then push each Cover into place. Repeat for the remaining covers. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 66 Ramp Pin. Note: The Ramps are heavy and awkward, BendPak recommends having two people install them; one to hold the Ramp, the other to put the components into place. 4. Repeat Steps 2 and 3 for the remaining Ramp. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts —...
  • Page 67 Vehicles or personnel on the Lift. The Anti-Slip Tape is provided in a single roll measuring 6 in. x 24 ft. (152 mm x 7.3 m). BendPak suggests cutting the Tape into four equal lengths 72 in. (1,829 mm) long.
  • Page 68 P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 69 9. Move the Lift to the desired location. 10. Raise the Lift to a locking position and engage it there. 11. Take off all four Caster Kit assemblies. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 70 Apply a small amount of White Lithium Grease or similar on the inside of the Lift Posts where the Slide Blocks travel up and down. Repeat monthly or as required. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 71 Perform an Operational Test BendPak strongly recommends performing an Operational Test of the Lift with a typical Vehicle before beginning routine use (a typical Vehicle is not required but is recommended). ⚠ DANGER Remember that lifting a Vehicle is a serious endeavor with life-threatening risks.
  • Page 72 If it has not been done already, perform an Operational Test of the Lift with a typical Vehicle. Refer Performing an Operational Test. • Make sure a copy of the Installation and Operation Manual remains with the Lift. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...

  • Page 73: Operation

    Check the Vehicle. Never exceed the Lift’s weight rating. Do not allow people inside a Vehicle • you are going to raise. Make sure the Vehicle is not overbalanced on either end or side. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 74 Safety Locks; release release Pushbutton and Lowering Handle when Lowering Handle. they stop. press and hold Pushbutton. 5. Make sure all four Posts are engaged at same height. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 75 5. With the Runways engaged on the Safety Locks, check around the Vehicle to make sure there are no obstructions, and both ramps are resting on Safety Locks. If you see anything wrong, fix it before anyone works near the Runways. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 76 5. When the Runways are fully lowered (on the ground), release the Air Pushbutton and the Lowering Handle. 6. Remove the Tire Chocks. 7. Remove the Vehicle or Boat Trailer off the Runways when the path is clear and safe. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...

  • Page 77: Maintenance

    Do not operate your Lift if you find maintenance issues; instead, take the Lift out of service, then contact your dealer, visit bendpak.com/support, email support@bendpak.com, or call (800) 253-2363, select option 7 then 4. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts...
  • Page 78 Visually check for any broken wires. One way to check for crown breaks is to run a cloth along the rope to check for possible snags. d. With an awl, probe between wires and strands and raise any wires that appear loose. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 79 Torque Chart P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...

  • Page 80: Troubleshooting

    Make sure the Power Unit is receiving power. If the Hydraulic Fluid is dirty, replace it with clean fluid. Make sure the Lift is not overloaded. Contact BendPak Support bendpak.com/support, email support@bendpak.com, or call (800) 253-2363. Runways do not lower past the nearest Problem with the Air Line;...
  • Page 81 4. Add additional Hydraulic Fluid if necessary. If your Lift is still moving erratically or making odd noises after bleeding the Hydraulic System, refer to Troubleshooting for more information. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...

  • Page 82: Wiring Diagrams

    Wiring Diagrams 5585014 5585280 P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 83 5585079 5585780 P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...

  • Page 84: Labels

    Labels P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 85 P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 86 P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...

  • Page 87: Parts Drawings

    Parts Drawings Model: HD-7500BLX __________________________________________________________________________________________________ P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 88 _________________________________________________________________________________________________ P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 89 __________________________________________________________________________________________________ P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 90 P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 91 Model: HD-75BXT P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 92 P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 93 P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 94 P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 95 P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 96 Model: HD-7500PBX ____________________________________________________________________________________________ P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 97 __________________________________________________________________________________________________ P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 98 __________________________________________________________________________________________________ P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 99 __________________________________________________________________________________________________ P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 100 P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 101 The ALI Store is your trusted source for workplace safety! Visit today and get the training and materials you need to work safely: www.autolift.org/ali-store/. P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...

  • Page 102: Maintenance Log

    Maintenance Log P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 103 Maintenance Log P/N 5900174 HD-7500BLX/75BXT/7500PBX Series Four-Post Lifts — Rev. D — March 2024...
  • Page 104 30440 Agoura Road Agoura, CA, 91301 USA bendpak.com © 2024 BendPak Inc. All rights reserved.

This manual is also suitable for:

Hd-75bxtHd-7500pbx

Table of Contents