Sungrow SG1100UD Series User Manual

Sungrow SG1100UD Series User Manual

Dc mplc communication configuration
Hide thumbs Also See for SG1100UD Series:

Advertisement

Quick Links

User Manual
Instructions for DC MPLC Communication Configuration
SG1100UD Series
SG1100UD
SeriesInstructions for DC MPLC
ManualInstructions for DC MPLC
Communication Configuration-
UEN-Ver12-202404
Instructions for DC MPLC Communication Configuration-UEN-Ver12-202404

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SG1100UD Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Sungrow SG1100UD Series

  • Page 1 User Manual Instructions for DC MPLC Communication Configuration SG1100UD Series SG1100UD SeriesInstructions for DC MPLC Communication ConfigurationUser ManualInstructions for DC MPLC Communication Configuration- UEN-Ver12-202404 Instructions for DC MPLC Communication Configuration-UEN-Ver12-202404...
  • Page 3: Table Of Contents

    Contents 1 About This Manual ...................1 1.1 Target Group ....................1 1.2 Validity......................1 1.3 How to Use This Manual .................1 1.4 Notice......................1 1.5 Symbols in the Manual ..................2 2 Operation Procedure ..................3 3 Communication Address Setting ..............4 3.1 Communication Topology ................4 3.2 Set MPLC Master Node Address on DIP Switch..........4 3.3 Set PVS Address on DIP Switch ..............6 4 Operation on WEB...
  • Page 5: About This Manual

    Due to the continuous improvement of the software, the software you use may deviate from the description or examples provided in this manual, regarding the interface or function. In this case, the most up-to-date version of software prevails. Please contact SUNGROW if you have any questions when using the software.
  • Page 6: Symbols In The Manual

    1 About This Manual User Manual Symbols in the Manual Symbols that may appear in this manual are listed below. Please read carefully for better use of this manual. "DANGER" indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
  • Page 7: Operation Procedure

    Operation Procedure figure 2-1 Operation Flow Chart...
  • Page 8: Communication Address Setting

    Communication Address Setting To enable DC MPLC communication, you need to set the communication addresses of the inverter units and PVS (combiner boxes) separately. Communication Topology The typology diagram of communication among the PVS, inverter unit, and smart communi- cation unit (SCU) is as shown in the figure below, with SG4400UD as an example. figure 3-1 Topology Diagram of Device Communication Set MPLC Master Node Address on DIP Switch Each inverter unit has a MPLC master node module.
  • Page 9 User Manual 3 Communication Address Setting Step 1 Open the cabinet door on the DC side of the inverter unit. The MPLC master node module is set on the cabinet door, as shown in the picture below.
  • Page 10: Set Pvs Address On Dip Switch

    3 Communication Address Setting User Manual Step 2 Set the DIP value for the MPLC master node module of the inverter unit. MPLC master node address = 232 + DIP value. The DIP value is set using the DIP switch below.
  • Page 11 User Manual 3 Communication Address Setting Step 1 Disassemble the PVS and find the monitoring board. The board has a PVS backplane and a DC MPLC slave board, as shown in the picture below. figure 3-2 Monitoring Board *The picture is for reference only and the product on the site may differ. Step 2 Press and hold the push-button switch K1 for over 3 seconds until the digital tube shows “A:001”.
  • Page 12: Operation On Web

    Operation on WEB Preparation Before Login You can visit the SCU WEB system on the PC or the mobile device. 4.1.1 Login (PC) Step 1 Connect the PC to the commissioning network port on the SCU with a network cable. Step 2 Configure the IP address of the PC.
  • Page 13: Enable Mplc Master Node

    User Manual 4 Operation on WEB Step 4 Enter the password “pw1111” and click Login to log into the system as an O&M user. Please change the password in time at your first login to ensure your account safety. - - End Enable MPLC Master Node Step 1 On the WEB system, choose “System→Port Parameter→RS485”, as shown in the figure below.
  • Page 14 4 Operation on WEB User Manual Step 1 Add a PVS. Choose “Device Maintenance→Device list”, and click “Add Device”. Then, in the pop-up dialog, as shown below, complete the parameter settings. table 4-1 Add Device Add Device Device Parameters Device Type Select “Combiner Box”.
  • Page 15: Set Array Id For Master/Slave Node

    User Manual 4 Operation on WEB Step 2 Configure the topological relationship between the master node and slave node. Click on the right, and enter the device information based on the actual connection be- tween the slave node and master node. For example, if a PVS slave node is connected to the Branch 2 port of the MPLC master node of inverter unit #4, set the parameters according to the figure below.
  • Page 16 4 Operation on WEB User Manual Step 1 Set the master node. Choose “System→Port Parameter→MPLC”. Select the master node, and click . Then, based on the on-site arrangement, enter the array ID in the pop-up dialog, and click “Next”. If the device information is not shown on this page, choose “Action→PLC Search” to search for the device again, as shown in the figure below.
  • Page 17 User Manual 4 Operation on WEB Step 4 Considering the difference in version, for some versions, the master and slave nodes need to be restarted so that the settings can take effect. Restart the slave node first. Select all slave nodes under the master node, and click “Restart slave node”.
  • Page 18 Sungrow Power Supply Co., Ltd. www.sungrowpower.com...

This manual is also suitable for:

Sg6600ud-mvSg8800ud-mv

Table of Contents