Hella 358118581 Operation Instructions

Installation and Operation Instructions
358118581 QUAD LED SLIM Warning Light Head
IMPORTANT: Please read all of the following instructions before installing your new HELLA QUAD LED SLIM WARNING LIGHT HEAD.
WARNING!!!!
Failure to install or use this product according to manufacturer's recommendations may result in property damage, serious injury, and/or death to those you
seek to protect!
▪
Proper installation of this product requires the installer to have a good understanding of automotive electronics, systems, and procedures.
▪
This product contains high-intensity LEDs. Do not stare directly into these lights. Momentary blindness and/or eye damage could result.
▪
Use only soap and water to clean the outer lens.
▪
Do not install this product or route any wires in the deployment area of your air bag. Equipment mounted or located in the air bag deployment area will damage or reduce
the effectiveness of the air bag, or become a projectile that could cause serious personal injury or death. Refer to your vehicle owner manual for the air bag deployment
area. The User/Installer assumes full responsibility to determine proper mounting location, based on providing ultimate safety to all passengers inside the vehicle.
▪
If mounting this product requires drilling holes, the installer must be sure that no vehicle components or other vital parts could be damaged by the drilling process.Check
both sides of the mounting surface before drilling begins. Also de-burr any holes and remove any metal shards or remnants. Install grommets into all wire passage holes.
▪
Inspect and operate this product regularly to confirm its proper operation and mounting condition. Do not use a pressure washer to clean this product.
▪
For this product to operate at optimum efficiency, a good electrical connection to the chassis ground must be made. The recommended procedure requires the product
ground wire to be connected directly to the NEGATIVE (-) battery post.
▪
It is recommended that these instructions be stored in a safe place and referred to when performing maintenance and/or reinstallation of this product.
▪
Failure To Follow These Safety Precautions And Instructions Could Result In Damage To The Product Or Vehicle And/Or Serious Injury To You And Your Passengers!
MOUNTING:
Screw No.:
③
④
⑥
⑤
②
②
1 2
①
④
③
MATERIAL :
材料 :
TREATMENT :
處理 :
⑧
OPERATION INSTRUCTION
1) Connections:
1 2
© HELLA Automotive Sales, Inc. • 201 Kelly Drive Peachtree City, GA 30269 USA • Ph. (770) 631-7500 • www.myhellalights.com • 03.2024
1
Stud
Bracket
③
④
①
⑤
③
⑥
L-Bracket
(Front)
①
騏宏科技股份有限公司
PROJECTION PART NO. : LNO6L
METHOD 品號 :
T W L DESCRIPTION :
XXXXXXX
品名:
NAME/姓名 DATE/日期
DRAWING NO. :
圖號 :
DESIGN BY:
無 CHECKED BY: SCALE/比例: 1:2 SIZE/圖面大小: A4
⑦
UNIT/單位: mm
APPROVED BY: REVISION/版次:
④
①
1
③
⑦
騏宏科技股份有限公司
PROJECTION
PART NO. :
METHOD 品號 :
DESCRIPTION :
品名: XXXXXXX
Wire ：
MATERIAL : NAME/姓名 DATE/日期
材料 : DRAWING NO. :
圖號 :
DESIGN BY:
TREATMENT :
CHECKED BY: SCALE/比例: 1:2
處理 : 無
APPROVED BY: UNIT/單位: mm
Red ：
White ：
Orange ：
Black ：
Blue ：
Yellow ：
Green ：
Part No.:
2
⑥X2
Universal
④ Bracket-V
⑥
⑥
①
④ L-Bracket
③
(Rear)
0
MATERIAL :
材料 :
①
TREATMENT :
處理 :
2
⑧
Group1 Group2
PROJECTION
METHOD
SIZE/圖面大小: A4
REVISION/版次: 0
Positive
MATERIAL :
材料 :
DESIGN BY:
TREATMENT :
CHECKED BY:
處理 : 無
Positive
APPROVED BY:
Negative
Apply to Negative For Pattern Switch / Apply To Postive For Dim
Synchronized Function
Apply To Negative For Mode Switch
OPTICAL
SELECT
L: Linear
⑦X1 ⑧x1
③
⑥
④
④ ①
③
1 2
①
騏宏科技股份有限公司
PROJECTION
④ PART NO. :
METHOD
品號 :
DESCRIPTION :
品名: XXXXXXX
NAME/姓名 DATE/日期
DRAWING NO. :
圖號 :
DESIGN BY:
CHECKED BY: SCALE/比例: 1:2 SIZE/圖面大小: A4
無
APPROVED BY: UNIT/單位: mm REVISION/版次:
③
1 2
Quad Color
Group3 Group4 Group5
騏宏科技股份有限公司
PART NO. :
LN6L
品號 :
T W L
DESCRIPTION :
XXXXXXX
Positive 品名: Positive
NAME/姓名 DATE/日期
DRAWING NO. :
圖號 :
SCALE/比例: 1:2
SIZE/圖面大小: A4
Positive
UNIT/單位: mm
REVISION/版次: 0
Positive Positive
LED COLORS:
A:Amber
B:Blue
C:White
R:Red
Universal
Bracket-H
③
④
⑥
①
Surface
Mounting
騏宏科技股份有限公司
PROJECTION PART NO.
METHOD 品號 :
T W L
DESCRIPT
品名:
MATERIAL :
NAME/姓名 DATE/日期
材料 : DRAWING
圖號 :
DESIGN BY:
TREATMENT :
CHECKED BY: SCALE/比
處理 : 無
APPROVED BY: UNIT/單位
0
①
騏宏科技股份有限公司
PROJECTION
PART NO. : LN6L
METHOD 品號 :
DESCRIPTION : XXXXXXX
品名:
MATERIAL :
NAME/姓名 DATE/日期 DRAWING NO. :
材料 :
圖號 :
DESIGN BY:
TREATMENT :
處理 : 無 CHECKED BY: SCALE/比例: 1:2 SIZE/圖面大小: A4
APPROVED BY: UNIT/單位: mm REVISION/版次: 0
Group6 Group7
Positive
Positive Positive
Positive Positive
Page 1 of 5