Advertisement

OT15

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the OT15 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for ONESPORT OT15

  • Page 1 OT15...
  • Page 3 1.Handlebar installation 2.L ight installation 3.Front wheel installation 4.Pedal installation 5.Install the saddle seat 6.Take out and install the battery 7.Accessory Installation 8.Switch on/off...
  • Page 4 Parts OT15 parts 1. Saddle/seat post 1 set 2. 16 in 1 tool 1 pcs 3. Tail 1pcs 4. Pedal 1 pair 5. Front reflector 1set 6. Bell 1 pcs 7. Wheel reflector 2sets 8. Front wheel quick release lever 1 pcs 1.
  • Page 5: Handlebar Installation

    1.Handlebar installation 1.Rotate the riser toward the headstock, and adjust the relative parallelism and perpendicularity of the riser, front fork and frame.
  • Page 6 2.Tighten the top cover 3.Use the 4# Allen key in the 16 in 1 tool to screw with the 5# Allen tighten the screws at "a" and "b" in the figure. key in the 16 in 1 tool。 Note: Tighten the two screws gradually. not tighten one screw first, and then tighten the other...
  • Page 7 4.Close the top cover screw plug 。...
  • Page 8 5.Use the 4 # Allen key in the 16 in 1 tool to remove 4 front cover screws and the front cover of the riser.
  • Page 9 6.Put the handlebar into the riser and adjust the angle in the middle,close the front cover. Note: Do not twist the wires.
  • Page 10 7.Use the 4# Allen key in the 16 in 1 tool to gradually tighten the 4 front cover screws in the sequence shown in the figure.
  • Page 11 2.Front light installation 1.Pre install the front light 2.pre screw the nut 3.tighten the screw with the 5# onto the front fork with the Allen key in the 16 in 1 tool. fixing screw...
  • Page 12: Front Wheel Installation

    Front wheel installation 1.Loosen the nut in the figure with the 15 open end wrench in the 16 in 1 tool and remove the support shaft.
  • Page 13 Note: Put the disc into the brake。 2.Clamp the front wheel into the front fork。...
  • Page 14 3.Unscrew the quick release rod nut and take out the conical spring. 4.Inserting quick release lever. 5..Install the conical spring as shown in the figure.
  • Page 15 6.Screw on the quick release 7.Adjust the direction of the handle, adjust the rod nut as shown in the figure. appropriate screw tightness, and tighten the handle upwards. Note: During this process, ensure that the front wheel is in the center of the front fork tube. If there is deviation, loosen the wrench to adjust the position of the front wheel, and then lock the wrench.
  • Page 16: Pedal Installation

    4.Pedal installation right pedal left pedal The mark"R" on the pedal shaft is right pedal,the sign "L" refers to left foot pedal.
  • Page 17 Install right pedal: The mark "R" on the pedal shaft is the right pedal. First rotate the pedal shaft clockwise and pre tighten it, enter the crank of the right toothed disc, and then turn clockwise with the 15# open -end wrench to tighten...
  • Page 18 Install left pedal: The mark "L" on the pedal shaft is left pedal. First, rotate the pedal shaft counterclockwise and pre tighten it,enter the crank on the left side, and then use the 15# open -end wrench to rotate counterclockwise to tighten it.
  • Page 19 5.Install the saddle seat 1.Open the seat tube adjusting quick disconnecting lever according to the diagram direction...
  • Page 20 2.Place the taillights according to the 3.Insert the saddle seat and adjust it diagram,pull the rubber pull ring in the to the required height (note: Insert the direction of the arrow, and fasten it. seat tube to a depth that is buried above the safety scale line).
  • Page 21 note: Insert the seat tube to a depth that is buried above the safety scale line。 4.Press the quick release lever in the direction of the picture. Note: If the folding wrench is too tight to move or too loose, please adjust the screw at "1"...
  • Page 22 6.Take out the battery: 1.Pull up the handle at the 2.Turn the seat tube upward 3.Turn the key to "PUSH" for bottom of the saddle removing the battery. 。...
  • Page 23 4.Insert the battery to the 5.Press the saddle down bottom, make it fully contact until it fully engages with with the discharge plug. the seat tube. 。 。...
  • Page 24: Parts Installation

    7.Parts Installation 1.Using the screw driver in 2.Insert the front reflector bracket the 16 in 1 tool, loosen the into the handlebars. screws on the front reflector Use the screw driver used in tool bracket., 16 in 1 to tighten the screws.
  • Page 25 3.Clamp the wheel reflector into 4.Turn the reflector latch on and the spoke (the spokes should be use the flat-head screwdriver used inserted into the middle slot of the in the 16 in 1 tool to tighten the wheel reflector). reflector by about 90 degrees.
  • Page 26 8.Swtich on/off Long press " " in the figure to turn it on/off...

Table of Contents