Download Print this page
ONESPORT OT16 Quick Operation Manual

ONESPORT OT16 Quick Operation Manual

Hide thumbs Also See for OT16:

Advertisement

Quick Links

Advertisement

loading
Need help?

Need help?

Do you have a question about the OT16 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for ONESPORT OT16

  • Page 2 OT16 Quick Operation Guide...
  • Page 3 1.Unfold the frame 2.Install the saddle 3.Accessory Installation 4.Fixing the rear fender support rod 5.Install the pedal 6.Take out the battery 7.Swtich on/off...
  • Page 4: Parts & Assembly

    Parts Assembly OT16 parts 1. Saddle and seat tube 2. Pedal 3. Front reflector 4. Bell 5. Wheel reflector 6. 16 in 1 tool...
  • Page 5 1.Unfold the frame 1.Remove the packaging, 2.Close the folding part in 3.Pull up the folding place the ebike on flat the direction of the arrow. handle and close it. ground,then unfold the frame.
  • Page 6 4.Pull the folding handle in the direction of the arrow.
  • Page 7 5.Open the folding riser telescopic Insert the telescopic vertical pipe, adjust the required adjustment buckle,Insert the telescopic height, and press the adjustment buckle in the vertical pipe in the direction of the arrow direction of the arrow in the figure. Note: If the adjustment buckle is too tight or too loose, please adjust the screw at position "1"...
  • Page 8 7.Set up and close the 8.After confirming the quick 9.Note: Please adjust the screw at folding riser in the direction disassembly and insertion, lift the "1" if the folding handle is too tight of the arrow. pull rod and wrench in the or too loose.
  • Page 9 10.Press down the folding wrench to lock the folding riser.
  • Page 10 2.Install Saddle 1.Pull the quick release 2.Insert the seat tube, adjust it to a proper height, and lever of seat tube. lock the quick release handle in the direction . Note: Please adjust the screw at "1" If the folding handle is too tight or too loose.
  • Page 11 3.Parts Installation 1.Front Reflector Installation Guide: Slide the front reflector bracket into the corresponding position of the handlebars,tighten the screw with a Phillips screwdriver。...
  • Page 12 2.Installation Guide for wheel reflector: Place the wheel reflector on the reserved position of the wheel hub,use a Phillips screwdriver to tighten two screws "1" and "2". The operating instructions for front and rear wheel reflectors are the same。...
  • Page 13 4.Fixing the rear fender support rod: 2. Put the support 1.Use the 4 # rod through the Allen wrench in fixing screw and the 16 in 1 tool to remove the tighten it in the pre-installed corresponding screws and screw holes on gaskets of the both sides of the fender support...
  • Page 14 5.Install the pedal The "L" marked on the pedal shaft refers to the left pedal. First, counterclockwise rotate the pedal shaft that enters the crank by hand, and tighten it with a 15# open-ended wrench counterclockwise.
  • Page 15 The "R" marked on the pedal shaft refers to the right pedal. First, clockwise rotate the pedal shaft that enters the crank by hand, and tighten it with a 15# open-ended wrench clockwise.
  • Page 16 6.Take out the battery: 4.Pick up the battery handle and take out the battery. 1.Pull up the handle at the 3.Turn the key to "PUSH" for 2.Turn the seat tube upward. bottom of the saddle removing the battery. 。...
  • Page 17 8.Press the saddle down until it fully engages with the seat tube. 5.Align the battery to 6.Insert the battery to the bottom, make it 7.Turn the key to the the battery track. fully contact with the discharge plug. right to “OFF”, an.
  • Page 18 7.Swtich on/off 1.Insert the key and turn the key to the "ON" position by turning it to the right of the "OFF" position。 2.Switch on: Press the button shown in the picture。 1. Insert the key into the keyhole at figure 1, turn the key to the "OFF"...
  • Page 19 OT16 Appearance...