Download
Share
Print this page
  1. Manuals
  2. Brands
  3. ONESPORT Manuals
  4. Bicycle
  5. OT10
  6. Quick operation manual

ONESPORT OT10 Quick Operation Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
OT10 Quick operation guide

Advertisement

loading
Need help?

Need help?

Do you have a question about the OT10 and is the answer not in the manual?

Questions and answers

Related Manuals for ONESPORT OT10

Summary of Contents for ONESPORT OT10

  • Page 1 OT10 Quick operation guide...
  • Page 2 1. Deploy and install the whole vehicle. 2. Installation of front fender lamp 3. Seat package installation 4. Fitting installation 5. Pedal installation 6. Installation of rear fender 7. Take out and install the battery 8. Boot method...

  • Page 3: Description Of Parts

    Description of parts BK10 parts 1. 1 set of seat tube for seat bag 2. Pedal 1 pair 3. 1 front reflector 4. 1 bell 5. 2 sets of wheel reflectors 6. 16-in-1 tool 1 set 7. 7 one dust cover for bowl group 8.
  • Page 4 1.Deploy and install the whole vehicle. 2. Insert the telescopic vertical pipe, adjust the 1. Pull open the telescopic adjusting button of required suitable height, and press the adjusting the folding riser,Insert telescopic standpipe in button in the direction of the arrow in the figure. the direction of arrow.
  • Page 5 ↓ 4. Insert the telescopic vertical pipe, adjust the 3. Pull open the telescopic adjusting button required suitable height, and press the adjusting of the folding riser, button in the direction of the arrow in the figure. Insert telescopic standpipe in the direction Note: If the adjusting button is too tight or too loose, of arrow please adjust the screw at "1"...
  • Page 6 6. Insert the telescopic vertical pipe, adjust the 5. Pull open the telescopic required suitable height, and press the adjusting adjusting button of the folding riser, buckle in the direction of the arrow in the figure. Insert telescopic standpipe in the Note: If the adjusting button is too tight or too loose, direction of arrow please adjust the screw at "1"...
  • Page 7 8. Insert the telescopic vertical pipe, adjust the required suitable height, and press the adjusting 7. Pull open the telescopic adjusting button buckle in the direction of the arrow in the figure. of the folding riser,Insert telescopic standpipe Note: If the adjusting button is too tight or too loose, in the direction of arrow please adjust the screw at "1"...
  • Page 8 10. Insert the telescopic vertical 9. Pull open the telescopic 11. Pull open the telescopic pipe, adjust the required suitable adjustment button of the adjustment button of the height, and press the adjusting folding riser. folding riser. buckle in the direction of the arrow Insert telescopic standpipe in Insert telescopic standpipe in the figure.
  • Page 9 12. Pull open the telescopic 13. Insert the telescopic vertical pipe, adjust adjustment button of the the required suitable height, and press the folding riser, adjusting buckle in the direction of the arrow in Insert telescopic standpipe the figure. in the direction of arrow Note: If the adjusting button is too tight or too loose, please adjust the screw at "1"...
  • Page 10 2. Installation of front fender lamp 1. Pre-install headlights and 2. Tighten the screws with mudguards on the front fork with the No.5 Allen wrench in the headlight fixing screws. 16-in-1 tool.
  • Page 11 3. Use the 4. Screw the No.4 Allen stick wrench in through the the 16-in-1 fender stick tool to fixing screw remove the and tighten fender stick it in the fixing correspondi screws and ng screw gaskets pre- holes on installed on both sides the left and...
  • Page 12 5. Pre-install headlights and 6. Tighten the 7. Tighten the mudguards on the front fork screws with the screws with the with headlight fixing screws. No.5 Allen key in the No.5 Allen key in the 16-in-1 tool. 16-in-1 tool.
  • Page 13 8. Pre-install headlights and 9. Tighten the screws with the No.5 mudguards on the front fork Allen key in the 16-in-1 tool. with headlight fixing screws.
  • Page 14 10. Install the front wheel butterfly plate into the butterfly brake, and install the front axle core into the front fork hook.
  • Page 15 11. Unscrew the quick release lever nut and take out a conical spring. 12. Insert the quick release screw, and install the small end of the conical spring inward as shown.
  • Page 16 13. Screw on the quick release 14. Adjust the direction of the handle, adjust the rod nut as shown. appropriate screw tightness, and fasten the handle upwards. Note: During this process, ensure that the front wheel is in the center of the front fork tube. If there is any deviation, please loosen the handle to adjust the position of the front wheel, and then lock the handle.
  • Page 17 3. Seat package installation 3. Pull the quick release handle of seat tube adjustment away according 1. Pull the quick release to the drawing direction. handle of seat tube adjustment away according to the drawing direction. 2. Insert the seat tube, adjust it to the required height, and press the quick release lever according to the drawing direction.
  • Page 18 4. Press the quick release handle in the direction of the drawing. Note: If the folding wrench is too tight or too loose, please adjust the screw at "1" appropriately.
  • Page 19 4. Installation of wheel reflector Press the quick release handle in the direction shown in the figure. Note: If the folding wrench is too tight or too loose, please adjust the screw at "1" appropriately.

  • Page 20: Pedal Installation

    5. Pedal installation 1. Pedal installation method: The pedal shaft is marked with "L" for left pedal. First, turn the pedal shaft counterclockwise by hand. Enter the left crank, and then turn it counterclockwise with No.15 open-ended wrench. The pedal shaft is marked with "R" for right pedal. First, turn the pedal shaft clockwise by hand. Enter the left crank, and then turn it clockwise with No.15 open-ended wrench to tighten it.
  • Page 21 1. Pedal installation method: The pedal shaft is marked with "L" for left pedal. First, turn the pedal shaft counterclockwise by hand. Enter the left crank, and then turn it counterclockwise with No.15 open-ended wrench.
  • Page 22 The pedal shaft is marked with "R" for right pedal. First, turn the pedal shaft clockwise by hand. Enter the left crank, and then turn it clockwise with No.15 open-ended wrench to tighten it.
  • Page 23 6. Fixing method of rear fender strut 2. Screw the 1. Use the stick through the No.4 Allen fender stick wrench in fixing screw and the 16-in-1 tighten it in the tool to corresponding remove the screw holes on fender stick both sides of the fixing frame with No.4...
  • Page 24 7. Take out the battery operation steps 4. Pick up the battery handle and extract the battery. 3. Turn the key to the "PUSH" 1. Turn the handle at the bottom of the bag. 2. Turn the seat tube turnover head position to take out the battery.
  • Page 25 4. Turn the handle at the bottom of the bag. 5. Turn the seat tube turnover head upward.
  • Page 26 6. Turn the handle at the bottom of the bag. 7. Turn the seat tube turnover head upward.
  • Page 27 8.8. Put in the battery operation steps 1. Turn the handle at the bottom of the bag. 2. Turn the seat tube turnover head upward.
  • Page 28 3. Turn the handle at the 4. Turn the seat tube turnover head upward. 5. Turn the seat tube bottom of the bag. turnover head upward.
  • Page 29 3. Turn the handle at the 4. Turn the seat tube turnover 5. Turn the seat tube turnover bottom of the bag. head upward. head upward.
  • Page 30 9. Installation of front reflector 4. Sleeve the front reflector 1. Use the Phillips 3. Use the Phillips 2. Use the Phillips bracket into the screwdriver in the 16- screwdriver in the 16- screwdriver in the 16- corresponding position of in-1 tool to loosen the in-1 tool to loosen the in-1 tool to loosen the...

  • Page 31: Bell Installation

    10. Bell installation 2. Sleeve the bell bracket into the 1. Use the Phillips screwdriver in the 16- corresponding position of the in-1 tool to loosen the screws on the bell handlebar, bracket. Just lock the screw with a Phillips screwdriver.
  • Page 32 9. Boot operation 1. Insert the key, turn the key to the right in the "OFF" position and turn it to the "ON" position. 2. Press the switch on the instrument in the figure. 1. Insert the key into the keyhole as shown in Figure 1, and turn the key in the "OFF"...
  • Page 33 OT10 Finished product y...