ONESPORT OT18 Quick Operation Manual
  1. Manuals
  2. Brands
  3. ONESPORT Manuals
  4. Bicycle
  5. OT18
  6. Quick operation manual

ONESPORT OT18 Quick Operation Manual

Hide thumbs

Advertisement

Table of Contents

QuickOperationGuide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the OT18 and is the answer not in the manual?

Questions and answers

John Witney
January 20, 2025

How to fit enclosed throttle

0
1 comments:
Mr. Anderson
February 4, 2025

The enclosed thumb throttle for the ONESPORT OT18 needs to be installed manually. Follow these steps:

1. Locate the Thumb Throttle: It is included in the box contents.
2. Attach to Handlebar: Securely fit the thumb throttle onto the handlebar.
3. Adjust Position: Ensure it is positioned comfortably for easy access during use.
4. Connect Wiring: Connect the throttle's wiring to the appropriate connector, ensuring it is properly aligned.

Use the provided operation guide or manual for additional details if needed.

This answer is automatically generated

0

Related Manuals for ONESPORT OT18

Summary of Contents for ONESPORT OT18

  • Page 1 QuickOperationGuide...
  • Page 2 1. Riser installation 2. Font fender Installation 3. Front wheel installation 4. Rear fender installation 5. Foot pedal installation 6. Saddle installation 7. Battery removing and installation steps 8. Front reflector installation 9. Wheel reflector installation 10. Bell installation 11. Ebike startup...
  • Page 3 Parts instruction BK8 parts 1. Saddle/Seat post 1 set 2. Pedal 1 pair 5 6 7 3. Front reflector 1 set 4. Bell 1 pcs 5. Wheel reflectors 2 sets 6. 16 in 1 Tools 1 pcs 7. Headset cover 1 pcs 8.

  • Page 4: Riser Installation

    1.Riser installation Note: The depth of inserting the seat tube should be buried beyond the safety tick mark. 3.Pre -tighten the screws with the 6# key from the 16 -in -1 2.Insert the handlebar into 1.Put the headset cover on the tool.
  • Page 5 4.Adjust the relative parallelism 5.Tighten the screws with 6.Snap on the top cover and perpendicularity of the the 6# Allen key in the 16 - screw plug. handlebar, front fork and frame. in -1 tool.
  • Page 6 7.Turn the adjusting handle 8.Use the 6# Allen key in the 16 -in - clockwise or counterclockwise 1 tool to tighten the screws of the to the right angle. handlebar.

  • Page 7: Front Fender Installation

    2 . Front fender installation 1. Pre -install the front light 2.Pre -tighten the nut. 3.Tighten the screws with a No. 5 Allen and fender on the front key and a No. 10 socket wrench. fork with the fixing screw.
  • Page 8 4.Use the 4# Allen key in the 5. Fix the front fender stick in 16-in -1 tool to remove the pre - the screw hole corresponding installed screws of the mud to the front fork and tighten plate stick on both sides of the the screw with the 4 # Allen front fork.

  • Page 9: Front Wheel Installation

    3.Front wheel installation 1.Use the No. 15 open -ended wrench in the 16-in -1 tool to loosen the nut and remove the fork foot protection shaft.
  • Page 10 2.Install the front wheel disc into the brake, then clamp the front wheel axle core into the front fork.
  • Page 11 3.Unscrew the quick-release lever nut and take out a conical spring 4.Insert the quick-release screw then put the small end of the conical spring inward.
  • Page 12 6.Adjust the direction of the handle and 5.Screw on the quick-release the appropriate screw tightness, then lever nut as shown. tighten the handle upwards. Note: During this process, ensure that the front wheel is in the center of the front fork tube.

  • Page 13: Rear Fender Installation

    4.Rear fender installation 2. Fix the rear fender sticks to the 1.Use the 5# Allen key in the 16 -in -1 corresponding screw holes of the tool to remove the pre -installed fender frame and use the 4# Allen key in support screws on both sides of the the 16 -in -1 tool to tighten them.
  • Page 14 5.Foot pedal installation Right pedal Left pedal The "R" marked on the pedal shaft is the right pedal. The mark "L" is the left pedal.
  • Page 15 2.Install the right pedal： The "R" on the pedal is the right pedal. First, turn the pedal clockwise by hand and screw it into the crank with toothed disc on the right, and then turn it clockwise with a 15# open - end wrench to tighten it.
  • Page 16 3.Install the left pedal： The "L" on the pedal is the left pedal. First, turn the pedal counterclockwise by hand and screw it into the left crank, and then turn it counterclockwise with a 15 # open - ended wrench to tighten it.

  • Page 17: Saddle Installation

    6 . Saddle installation Note: the depth of the seat tube should be buried below the safety mark) 1.Pull the seatpost clamp Insert the seat tube and adjust to quick release lever as shown the proper height (Note: the depth of the seat tube should be buried in the picture.
  • Page 18 3.Tighten the quick release lever in the direction shown in the picture. Note: If the folding wrench is too tight or too loose, please adjust the screw at "1" .
  • Page 19 7. Battery removing steps： 4.Pick up the battery handle and take out the battery 2.Hold this lever up to 3.Turn the key to "PUSH" to 1.Pull up the flip handle at remove the battery. open the saddle. the bottom of the saddle.
  • Page 20 Battery installation steps： 2.Insert the battery into the 3.Press the saddle 1.Align the battery down until it is bottom and make it in full slide with the battery contact with the discharge completely clamped track on the frame. plug, right-turn the key to with the seat tube.
  • Page 21 8 . Front reflector installation 3.Remove the screws 4.Clamp the front reflector 1. Loosen the screws on 2.Use a cross screwdriver to loosen bracket into the the front reflector bracket the screws on the front corresponding position of with the cross screwdriver reflector bracket the handlebar and tighten in the 16 -in -1 tool.
  • Page 22 9.Wheel reflector installation Snap the wheel reflector into the Turn into the reflector clip and screw it spoke (Note that the spoke should be about 90 degrees with the flat-blade inserted into the slot in the middle of screwdriver in the 16 -in -1 tool to fix it. the wheel reflector).

  • Page 23: Bell Installation

    10.Bell installation 2.Clamp the bell bracket into the 1.Using the Phillips screwdriver in the 16 - corresponding position of the handlebar then in -1 tool to loosen the screw on the bell tighten the screw with a cross screwdriver. bracket.
  • Page 24 11.Ebike startup 1.Insert the key and right - turn it from "OFF" to "ON". 1.Insert the key into the keyhole in Figure 1, and right-turn it from "OFF" to "ON". 2.press to turn on or off. 2. Press the switch in Figure 2 to turn it on. Otherwise, it is turned off.

Table of Contents