Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ONESPORT OT29
Summary of Contents for ONESPORT OT29
- Page 1 OT29 Quick Operation Guide...
- Page 2 OT29 Quick Operation Guide...
- Page 3 1. Handlebar installation 2. Front wheel,front headlight and front fender installation 3. Saddle installation 4. Wheel reflector and bell installation 5. Pedal installation 6. Rear fender installation 7. Battery installation 8. Switch on/off...
- Page 4 Parts instruction OT29 parts 1. Saddle/seat post 1 set 2. 16 in 1 tool 1set 3. Pedal 1 pair 4. Front reflector 1set 5. Bell 1 pcs 6. Wheel reflector 1pair 7. Front wheel quick release 1pcs 8. Folding riser 1pcs 9.
-
Page 5: Handlebar Installation
1.Handlebar installation Open the riser folding buckle and After inserting the folding riser,lock insert the riser into the front fork the riser slightly in the direction of of the head tube along the arrow the arrow in the picture direction... - Page 6 Open the folding riser quick Adjust the telescopic standpipe The telescopic riser is installed release, The telescopic riser is to a proper position, tighten the Note: If the quick release handle is loaded into the folding riser in quick release nut, and fasten the too loose or too tight to move, the direction of the arrow in the quick release...
- Page 7 Adjust the handlebars to be Stand the folded riser in the parallel to the front fork direction of the arrow in the picture...
- Page 8 Lower the folding riser and lock the Hold the folding riser upright and the screw in the direction of the arrow handle of the folding buckle upward to in the picture lock the riser...
- Page 9 Fasten the handle of the folding buckle Folding riser installed in the direction of the arrow in the picture...
- Page 10 2.Front wheel, front headlight and front fender installation Using the #5 Allen wrench in the Remove the front fork protection tool, remove the headlight fixing stick with the #15 open end screws indicated by the arrows in wrench in the tool the figure below...
- Page 11 Using the #4 Allen wrench in the tool, remove the fender stick fixing screws and spacers preinstalled on both sides of the front fork, and then install the fender stick tightening screws...
- Page 12 Install the headlight and front fender lifting lug on the front fork with the headlight retaining screws and tighten the screws with the #5 Allen wrench in the too...
- Page 13 Install the front wheel, the brake pad into the brake to make the gap, the front wheel shaft into the front fork hook claw...
- Page 14 Unscrew the quick release nut of the Insert the quick release rod and load it front wheel and take out 1 conical inward with the small head of the spring conical spring as shown...
- Page 15 Fasten the quick release handle firmly. If it is too loose, Screw on the quick release rod conical please tighten the opposite nut. During this process, spring nut according to the figure, ensure that the front wheel is in the center of the front with the small head of the conical fork tube.
-
Page 16: Saddle Installation
3.Saddle installation Insert seat tube and adjust to proper height Open the quick release handle of the within safety scale on seat tube seat tube clamp in the direction of the figure... - Page 17 Tighten the quick release nut of the tube clamp, and then fasten the quick release handle of the tube clamp.If the handle is too tight or too loose, please adjust the quick release nut tightness...
- Page 18 4.Wheel reflector and bell installation After securing the reflector in the clamp slot, use the screwdriver in the tool to tighten the screws and install the front and rear reflectors...
- Page 19 Loosen the screws on the front Install the front reflector on the The front reflector is reflector support using the handlebars and tighten the installed screwdriver in the tool, and install screws with the screwdriver in the front reflector support into the the tool reflector plate along the guide rails...
- Page 20 Loosen the screws on the bell bracket Slip the bell bracket into the handlebars, using the screwdriver in tool 16 in 1. Use a screwdriver to lock the screws...
-
Page 21: Pedal Installation
5.Pedal installation The "R" marked on the foot shaft is the "L" marked on the foot shaft means stepping right foot. Rotate the foot shaft clockwise with the left foot. First ti rotate the foot shaft by hand and screw it into the right crank, counterclockwise by hand and screw it into the then rotate it clockwise and tighten it with crank on the left side. -
Page 22: Rear Fender Installation
6.Rear fender installation Remove the fender support rod fixing screws and gaskets preinstalled on the left and right sides of the frame with the #4 Allen wrench in the tool, and lock the support rod with screws... -
Page 23: Battery Installation
7. Battery installation Open the buckle in the direction of the arrow in the figure, and open the buckle outwards... - Page 24 Fold the pipe tube, turn the key counterclockwise according to the figure, open the battery lock and pull out the battery...
- Page 25 Slide the battery into the battery compartment in the direction of the arrow in the figure...
- Page 26 Insert the key clockwise to lock the battery, remove the key and close the frame...
- Page 27 Then fasten the handle of the folding buckle, and the battery is installed successfully...
- Page 28 8.Switch on/off Long press the middle button of the upper instrument to perform the on-off operation...
Need help?
Do you have a question about the OT29 and is the answer not in the manual?
Questions and answers