Related Manuals for Boss Snowplow Genesis Push Pal Series
Summary of Contents for Boss Snowplow Genesis Push Pal Series
- Page 1 Form No. MSC25768 Rev A Owner's Manual Genesis Series Push Pal ® Part No. LIQ28848—Serial No. 400000000 and Up *MSC25768* Register at www.bossplow.com. Original Instructions (EN)
- Page 2 This product complies with all relevant European model and serial numbers on the product. Write the directives; for details, please see the separate product numbers in the space provided. specific Declaration of Conformity (DOC) sheet. BOSS Products limited consumer warranty and BOSS Products commercial warranty policies are located at www.bossplow.com.
-
Page 3: Table Of Contents
Contents Safety Safety ............... 3 Safety-Alert Symbol Safety-Alert Symbol..........3 General Safety ........... 3 The safety-alert symbol (Figure 2) shown in this Safety and Instructional Decals ......4 manual and on the machine identifies important safety Setup ................ 5 messages that you must follow to prevent accidents. Unfolding the Handle .......... -
Page 4: Safety And Instructional Decals
Safety data sheets (SDS) are available at www.bossplow.com on the Tech Support/Technical Information page. Safety and Instructional Decals Safety decals and instructions are easily visible and are located near areas of potential danger. Replace every damaged or missing decal. decal133-8061 133-8061 decalbatterysymbols Battery Symbols... -
Page 5: Setup
Setup Note: Determine the left and right sides of the machine from the normal operating position. Unfolding the Handle Push the detent pin in (Figure Raise the handle and secure it in the upright position with the pin. g415061 Figure 4 Checking the Tire Pressure Pressure: 124 kPa (18 psi) Installing the Battery and... -
Page 6: Product Overview
Product Overview g414642 Figure 5 1. Handle 6. Fan tip 2. Spray gun 7. Vent cap 3. Quick-connect hose 8. Handle pin 4. Brine container 9. Pump 10. Battery 5. Spray bar... -
Page 7: Controls
Controls Become familiar with all the controls before you start the engine and operate the machine. Specifications Note: Specifications and design are subject to change without notice. Machine depth 43.2 cm (17 inches) Machine width 53.3 cm (21 inches) Machine height with handle 124.5 cm (49 inches) raised Machine height with handle... -
Page 8: Before Operation
Performing Daily Operation Maintenance Before Operation Before starting the machine each day, perform the Each Use/Daily procedures listed in Maintenance (page 12). Before Operation Safety General Safety • Never allow children or untrained people to operate the machine. Local regulations may restrict the age of the operator. -
Page 9: During Operation
During Operation • Do not use the hand sprayer if the hose, trigger lock, nozzle, or any other part is damaged or missing. General Safety • Do not use the hand sprayer if there are any leaks in any hoses, fittings, or other components. •... -
Page 10: After Operation
When you are done spraying, release the handle Install the cap, install the container into the and switch the machine to the O position. machine, and attach the quick-connect hose. Spraying Tips Flushing the Sprayer • Do not overlap areas that you have previously System sprayed. -
Page 11: Transporting The Machine
Transporting the Machine Fold the handle and secure the machine to a trailer or truck to transport the machine. -
Page 12: Maintenance
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Maintenance Safety • Check all fasteners at frequent intervals for proper tightness to ensure that the machine is in safe • Before adjusting, cleaning, servicing, or leaving working condition. - Page 13 Install the battery into the machine and connect WARNING the battery cables; refer to Installing the Battery Incorrect battery cable routing could (page 13). damage the machine and cables, causing sparks. Sparks can cause the battery gases to explode, resulting in personal injury.
-
Page 14: Servicing The Fuse
Servicing the Fuse Drive System Maintenance The electrical system is protected by fuses. It requires no maintenance. If a fuse blows, check the component or circuit for a malfunction or short. Checking the Tire Pressure Replacing the In-Line Fuse Service Interval: Before each use or daily—Check the tire pressure. -
Page 15: Sprayer Maintenance
Sprayer Maintenance Cleaning Conditioner Specification Cleaning the Machine Conditioner specification: propylene glycol Service Interval: After each use—Empty the sprayer "non-toxic RV antifreeze” with corrosion inhibitor container. After each use—Flush the sprayer system. Important: Use only propylene glycol with corrosion inhibitor. Yearly or before storage—Condition the sprayer Do not use recycled propylene glycol. -
Page 16: Storage
Storage Storage Safety Do not store material in the sprayer tank. Storing the Machine Remove salt, sand, and grime from the external parts of the entire machine. Important: You can wash the machine with a mild detergent and water. Do not pressure-wash the machine. -
Page 17: Troubleshooting
Troubleshooting Problem Possible Cause Corrective Action The sprayer pump does not prime. 1. The sprayer container vent cap is 1. Open the vent cap. closed. 2. Bring the machine to a warm area to 2. The brine in the hoses is frozen. thaw. - Page 18 Notes:...
- Page 19 Notes:...
- Page 20 California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.
Need help?
Do you have a question about the Genesis Push Pal Series and is the answer not in the manual?
Questions and answers