Table of Contents
Advertisement
Quick Links
INSTALLATION
INSTRUCTIONS
MODEL 233-P/233-1.5-P
CLICK ANYWHERE on THIS PAGE to RETURN TO WATER PUMP WATER
PUMP PROTECTION SWITCHES & CONTROLS at InspectApedia.com
Rapid City, SD, USA, 09/2008
2880 North Plaza Drive, Rapid City, South Dakota 57702
(800) 843-8848 · (605) 348-5580 · fax (605) 348-5685
Revision B
Advertisement
Table of Contents
Related Manuals for SymCom PumpSaver Plus 233-P
Summary of Contents for SymCom PumpSaver Plus 233-P
- Page 1 INSTALLATION Revision B INSTRUCTIONS Rapid City, SD, USA, 09/2008 MODEL 233-P/233-1.5-P CLICK ANYWHERE on THIS PAGE to RETURN TO WATER PUMP WATER PUMP PROTECTION SWITCHES & CONTROLS at InspectApedia.com 2880 North Plaza Drive, Rapid City, South Dakota 57702 (800) 843-8848 · (605) 348-5580 · fax (605) 348-5685...
- Page 2 Refer to the appropriate wiring diagram for your specific application: • Typical wiring diagram – Figure 1 • Standard 3-wire control box – Figure 2 • Deluxe control box – Figure 3 • 2-Wire pump direct feed – Figure 4 © 2008 SymCom, Inc. All Rights Reserved...
- Page 3 PRESSURE SWITCH OR OTHER CONTROL TO THERMALLY OR IMPEDANCE PROTECTED MOTOR 4” STANDARD 3-WIRE CONTROL BOX 1/3 - 3hp FOR 233-P 1/3 - 1.5hp FOR 233-1.5- P FIGURE 2: Standard Control Box Wiring Diagram © 2008 SymCom, Inc. All Rights Reserved...
- Page 4 OR OTHER CONTROL A PRESSURE SWITCH CAN BE INSTALLED EITHER BEFORE ® OR AFTER THE PUMPSAVER PLUS PRESSURE SWITCH OR OTHER CONTROL TO THERMALLY OR IMPEDANCE PROTECTED MOTOR FIGURE 4: 2-Wire Pump Direct-Feed Wiring Diagram © 2008 SymCom, Inc. All Rights Reserved...
-
Page 5: Operation
The PumpSaver Plus has an adjustment knob to set the underload trip sensitivity. Setting SENSITIVITY to the middle position (straight up) is equivalent to SymCom’s standard underload trip level. Adjust the SENSITIVITY knob to increase/decrease underload sensitivity up to approximately ®... - Page 6 7. After 2 seconds, the CAL. and RUN LIGHTS will blink once. USING AN INFORMER The Model 233-P/233-1.5-P is equipped with an infrared LED that will communicate to a SymCom Informer—a handheld, battery-operated, diagnostic tool. The Informer—when directed at the Model 233-P/233-1.5-P —will display real-time voltage, current and power;...
-
Page 7: Troubleshooting
(if used), or check down on rapid cycling. Power the CAL. the RUN for a defective pressure or float must be removed and reapplied LIGHT LIGHT switch. to reset the unit. © 2008 SymCom, Inc. All Rights Reserved... -
Page 8: Physical Dimensions
PHYSICAL DIMENSIONS 2.93" FRONT VIEW (74.42) .375" 4.05" (102.87) (9.53) 4.50" (114.30) 5.26" (133.60) 2.90" (73.66) BOTTOM VIEW 2.17" (55.12) © 2008 SymCom, Inc. All Rights Reserved... -
Page 9: Specifications
Electrostatic Discharge (ESD) IEC 1000-4-2, Level 2, 4kV contact, 6kV air Safety Marks UL508 C22.2 No. 14 Dimensions 5.26” W x 2.93” H x 2.90” D Weight 14 oz. Mounting Methods #8 screws © 2008 SymCom, Inc. All Rights Reserved... - Page 10 NOTES © 2008 SymCom, Inc. All Rights Reserved...
- Page 11 NOTES © 2008 SymCom, Inc. All Rights Reserved...
- Page 12 Visit us at www.symcom.com to see our complete product listing! Can’t find what you’re looking for? SymCom designs and manufactures custom control boards too. Call us for details! © 2008 SymCom, Inc. All Rights Reserved...
Need help?
Do you have a question about the PumpSaver Plus 233-P and is the answer not in the manual?
Questions and answers