Table of Contents
Advertisement
Quick Links
AC speed control motor
SCM Motor
for Right Angle Shaft Hypoid Gear
JH / JL Gearhead
OPERATING MANUAL
Thank you for purchasing an Oriental Motor product.
This Operating Manual describes product handling procedures and safety precautions.
• Please read it thoroughly to ensure safe operation.
• Always keep the manual where it is readily available.
Table of contents
1 Introduction............................................................ 2
2 Safety precautions ................................................ 3
3 Precautions for use ............................................... 5
4 Preparation ............................................................. 6
4.1 Checking the product ................................................. 6
4.2 Combination tables ...................................................... 7
4.3 Information about nameplate.................................. 7
5 Installation .............................................................. 8
5.1 Installation location ..................................................... 8
5.2 Installation method ...................................................... 8
5.3 Installing a load ...........................................................10
permissible axial load ................................................12
6 Grounding .............................................................14
7 Maintenance · inspection ................................15
7.1 Inspection ......................................................................15
7.2 Warranty .........................................................................15
7.3 Disposal ..........................................................................15
8 Specifications .......................................................16
8.1 Specifications ...............................................................16
8.2 General specifications ...............................................16
8.3 Time rating ....................................................................16
9 Regulations and standards .............................17
HM-9460
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Oriental motor SCM
Summary of Contents for Oriental motor SCM
-
Page 1: Table Of Contents
HM-9460 AC speed control motor SCM Motor for Right Angle Shaft Hypoid Gear JH / JL Gearhead OPERATING MANUAL Thank you for purchasing an Oriental Motor product. This Operating Manual describes product handling procedures and safety precautions. • Please read it thoroughly to ensure safe operation. -
Page 2: Introduction
Operating manuals are not included with the product. Download from Oriental Motor Website Download Page or contact your nearest Oriental Motor sales office. Operating manual name SCM Motor Right Angle Shaft Hypoid Gear JH/JL Gearhead Motor OPERATING MANUAL (this document) -
Page 3: Safety Precautions
Safety precautions Safety precautions The precautions described below are intended to prevent danger or injury to the user and other personnel through safe, correct use of the product. Use the product only after carefully reading and fully understanding these instructions. WARNING Handling the product without observing the instructions that accompany a "WARNING"... - Page 4 Safety precautions CAUTION • Do not use the motor beyond its specifications. Doing so may result in electric shock, injury or damage to equipment. • Do not touch the motor during operation or immediately after stopping. The surface is hot and may cause a skin burn(s).
-
Page 5: Precautions For Use
Precautions for use Precautions for use This section covers restrictions and requirements the user should consider when using the product. z Be sure to match the output power and power supply voltage when combining a motor and speed controller z Connecting the motor and speed controller Use a connection cable (sold separately) when extending the wiring distance between the motor and the speed controller. -
Page 6: Preparation
Preparation Preparation Checking the product Verify that the items listed below are included. Report any missing or damaged items to the branch or sales office from which you purchased the product. Verify the model number of the purchased product against the number shown on the nameplate. „... -
Page 7: Combination Tables
Preparation Combination tables • Enter the code representing the power supply voltage in the box within the model name. JA: Single-phase 100 V 50/60 Hz JC: Single-phase 200 V 50/60 Hz UA: Single-phase 110/115 V 60 Hz EC: Single-phase 220/230 V 50/60 Hz •... -
Page 8: Installation
Installation Installation This section explains the installation method of a load in addition to the installation location and installation method of the product. Installation location Install the product in a well-ventilated location that provides easy access for inspection. • Indoors •... - Page 9 Installation „ Installing the motor to the mounting plate Use the mounting screw included with a gearhead to secure the motor and gearhead to the mounting plate. Do not leave a gap between the motor and mounting plate. The figures show the Hollow shaft. Hexagonal socket head screw Spring washer...
-
Page 10: Installing A Load
Installation Installing a load „ Hollow shaft type Mounting method of the load varies depending on the load shaft conditions. See the following figures. The hollow output shaft inside dimension is processed to a tolerance of H8, and incorporates a key slot for load shaft attachment. A load shaft tolerance of h7 is recommended. - Page 11 Installation z Recommended load shaft installation dimensions Unit: mm (in.) Gearhead model 4HB 5HB +0.027 +0.027 Inner Diameter of Hollow Ø12 Ø15 +0.0011 +0.0011 Shaft (H8) (Ø0.4724 (Ø0.5906 Recommended load shaft length Shaft Diameter of Load Ø12 Ø15 0.018 0.018 Shaft (h7) (Ø0.4724 (Ø0.5906...
-
Page 12: Permissible Radial Load And Permissible Axial Load
Installation Permissible radial load and permissible axial load The radial load and the axial load on the gearhead output shaft must be kept under the permissible values listed below. Note Failure due to fatigue may occur when the gearhead bearings and output shaft are subject to repeated loading by a radial or axial load that is in excess of the permissible limit. - Page 13 Installation „ JL Gearhead Radial load Axial load 10 mm (0.39 in.) 20 mm (0.79 in.) Distance from output shaft Permissible radial load [N (lb.)] Gearhead model Permissible axial load Distance from tip of gearhead output shaft [N (lb.)] Gear ratio 10 mm (0.39 in.) 20 mm (0.79 in.) 304 (68)
-
Page 14: Grounding
Grounding Grounding Be sure to ground the product using the Protective Earth Terminal on the motor. Grounding „ Ground terminal Use a crimp terminal described below for grounding. • Applicable crimp terminal: Round crimp terminal with insulation cover • Thread size of terminal: M4 •... -
Page 15: Maintenance · Inspection
Maintenance · inspection Maintenance · inspection Inspection It is recommended that periodic inspections would be conducted for the items listed below after each operation of the motor. If an abnormal condition is noted, discontinue any use and contact your nearest Oriental Motor sales office. Note Do not conduct the insulation resistance measurement or dielectric strength test with the motor and speed controller connected. -
Page 16: Specifications
Specifications Specifications Specifications Check on the Oriental Motor Website for the product specifications. General specifications Ambient 0 to +40 °C [+32 to +104 °F] (non-freezing) temperature Ambient 85% or less (non-condensing) Humidity Altitude Up to 1000 m (3300 ft.) above sea level Surrounding No corrosive gas, dust, water or oil. -
Page 17: Regulations And Standards
Regulations and standards Regulations and standards Check on the Oriental Motor Website for the regulations and standards. „ UL Standards, CSA Standards This product is recognized by UL under the UL and CSA Standards. „ CCC System This product is affixed the CCC Mark under the China Compulsory Certification System. It is also certified by CQC. „... - Page 18 Tel:1800-806-161 4-8-1 Higashiueno, Taito-ku, Tokyo Technical Support Tel:00 800/22 55 66 22 110-8536 Japan Tel:+81-3-6744-0361 Tel:1800-888-881 www.orientalmotor.co.jp/ja Unit 5 Faraday O ce Park, Rankine Road, Basingstoke, Hampshire RG24 8QB UK Tel:1800-120-1995 (For English) Tel:+44-1256347090 1800-121-4149 (For Hindi) Tel:+33-1 47 86 97 50...
Need help?
Do you have a question about the SCM and is the answer not in the manual?
Questions and answers