Advertisement

Quick Links

1. Features
Your electronic message board is ideal for advertisements and meetings. You can programme
up to four original messages and set the message board to repeatedly run a single message or
run several messages in a programmed sequence. You can also connect the message board to
your alarm system and programme a fifth message that only appears when an intruder triggers
your alarm system.
Additional features include :
Adjustable scrolling speed : controls the speed with which the message scrolls across the
Memory backup
Warning : Do not use the message board in your vehicle. Using such a device in your vehicle
endangers other motorists and constitutes a penal act is some countries.
2. Installation
You can place the message board on a horizontal surface or mount it on a wall. If you plan to
connect the display to your alarm system, you should select a location where people can read
the alarm messages, e.g. in front of a window.
Caution : This message board is designed for indoor use only. Protect the device against water,
moisture and excessive heat in order to ensure proper operation.
Placing the message board on a table
Place the message board on a stable and horizontal surface (e.g. a table). Use a screwdriver to
loosen the screws at the back of the device if you wish to adjust the viewing angle of the
message board. Retighten the screws afterwards.
FIG. 1
MML10 version 2
MML10 – Message Board
display.
: saves your messages for up to a year if the message board is not
connected to an AC power source.
1
GB

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MML10 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Velleman MML10

  • Page 1 MML10 – Message Board 1. Features Your electronic message board is ideal for advertisements and meetings. You can programme up to four original messages and set the message board to repeatedly run a single message or run several messages in a programmed sequence. You can also connect the message board to your alarm system and programme a fifth message that only appears when an intruder triggers your alarm system.
  • Page 2 4. Fit the keyhole slots of the back plate over the screws and press the back plate against the wall. Tighten the screws. 5. Attach the message board to the back plate and replace the washers and screws as shown below. FIG. 4 6. Adjust the viewing angle and tighten the screws. MML10 version 2...
  • Page 3 Power Failures The memory of the MML10 saves your messages for one year if the message board is not connected to a suitable power source. The message board will perform its standard self-test when the AC power supply is restored.
  • Page 4 : FIG. 8 Consequently, the display will show the contents of message 1. The message board always performs this self-test upon activation. The status indicator lights when a message is shown on the display. MML10 version 2...
  • Page 5: Activating/Deactivating The Display

    1. 8. Entering a Message 1. Activate the message board and wait for it to complete the self-test. 2. Open the keyboard cover. 3. Press "PROGRAM". The display will read "PROGRAM MODE : SELECT MESSAGE # ". MML10 version 2...
  • Page 6 - Press an arbitrary button to display the white character on that button. - Hold SHIFT and press an arbitrary button to display the blue character on that button. Note : Each message should contain between one and 601 characters. Spaces count as one character. MML10 version 2...
  • Page 7: Editing A Stored Message

    Read "Power Failures" under heading "3. Connecting the Device to a Suitable Power Source" (p. 3). 9. Editing a Stored Message 1. Activate the message board and wait for it to finish the self-test. 2. Press "EDIT/DELETE". The display reads "EDIT MODE : SELECT MESSAGE #". MML10 version 2...
  • Page 8: Selecting Messages

    Activate the message board and wait for it to complete its self-test. Message 1 will now start to scroll across the display until you select another message or deactivate the display. The message sequence is always 1, 2, 3, 4 when the sequential display function is not used. MML10 version 2...
  • Page 9: Special Features

    3, 1. The manufacturer’s sequence is 1, 2, 3, 4. Altering the Sequence Follow the procedure outlined under headings "8. Entering a Message" and "9. Editing a Stored Message" to change the sequence, but press 6 for the message number. The display MML10 version 2...
  • Page 10 Press "RESET" with a fine and sharp object in order to reset the device if it is not working properly. The message board will execute the self-test prior to starting up again. The messages are not erased. FIG. 16 MML10 version 2...

Table of Contents