Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Hubble Manuals
  4. Battery Pack
  5. AM-10
  6. Manual

Hubble AM-10 Manual

Hide thumbs Also See for AM-10:

Advertisement

Quick Links

Download this manual
AM-10
MANUAL
It is important that you read this manual before a琀琀emp琀椀ng the installa琀椀on of your
ba琀琀ery. Please take note of certain steps to ensure correct inverter compa琀椀bility.
Please visit
www.hubblelithium.co.za
WARNING:
Working with high voltage systems is dangerous. Do not a琀琀empt to modify your
inverter and ba琀琀ery setup unless you are certain you understand the risk. Speak
to a quali昀椀ed electrician if you are unsure.
V 1.0
for the latest version of this manual.

Advertisement

loading
Need help?

Need help?

Do you have a question about the AM-10 and is the answer not in the manual?

Questions and answers

Related Manuals for Hubble AM-10

Summary of Contents for Hubble AM-10

  • Page 1 V 1.0 AM-10 MANUAL It is important that you read this manual before a琀琀emp琀椀ng the installa琀椀on of your ba琀琀ery. Please take note of certain steps to ensure correct inverter compa琀椀bility. Please visit www.hubblelithium.co.za for the latest version of this manual.
  • Page 2 INDEX product description INTERFACE & SIZE PARALLEL CONNECTION OF BATTERIES installation notes DIP SWITCH SETTINGS interface de昀椀niton interface FUNCTIONS PARALLEL FUNCTIONS warnings COMPLETING SETUP...
  • Page 3 Product description SMART TECHNICAL SPECIFICATIONS Every module is AM-10 Model equiped with an independent BMS Ba琀琀ery Type LiFePO4 (LFP) system. Norminal Voltage (V) 51.2V Norminal Energy (KWH) 10KWH EASY Design Capacity 200AH INSTALLATION Design Years 15 Years Just plug & play.
  • Page 4 INTERFACE & SIZE POWER SWITCH DRY CONTACT RESET ADDRESS RS485 RS232 BATTERY LINK BATTERY + BATTERY -...

  • Page 5: Connection Of Batteries

    PARALLEL CONNECTION OF BATTERIES Connect the posi琀椀ve pole and posi琀椀ve pole in parallel, and the nega琀椀ve pole and nega琀椀ve pole in parallel, as shown in the 昀椀gure below: CORRECT METHODS OF BATTERY LINKING Note Diagram 1: Maximum of 4 batteries in parallel or maximum inverter current not exceeding 250Amps.
  • Page 6 2. As shown in the 昀椀gure below, 昀椀x the a琀琀ached six expansion bolts in the opening of the moun琀椀ng structure, and 琀椀ghten the nuts on the bolts. 3. Li昀琀 up the AM-10 ba琀琀ery carefully and hook it into posi琀椀on securely onto the wall mount bracket. BOX PENDANT OPENING POSITION...
  • Page 7 LED WORKING STATUS INDICATION SOC INDICATION LEDS NORMAL / ALARM STATUS REMARK / PROTECTION POWER OFF Dormancy All o昀昀 Fash 1 Standby state Normal According to the electricity instruc琀椀on STANDBY Flash 1 Flash 3 Cell low voltage Alarm Ligh琀椀ng Normal According to the electricity instruc琀椀on Alarm when (Power level indicates maximum LED...

  • Page 8: Dip Switch Settings

    DIP SWITCH SETTINGS Dialing code func琀椀on area: Master/Slave Se琀�ng Slave Address Se琀�ng CAN Bus terminal resistance se琀�ng From le昀琀 to right, are 1#~8# dial switches, switch up is ON, down is OFF. Dip switch 8# Dial ON means that the end resistor of the CAN port (for CAN inverters) is loaded; 8# Dial OFF means that the end resistor of the CAN port (for CAN inverters) is unloaded.
  • Page 9 Mark Master Ba琀琀ery \ Enable CAN BUS Port Slave 2 Slave 3 Slave 4 Slave 5 Slave 6 Slave 7 Slave 8 Slave 9 Slave 10 Slave 11 Slave 12 Slave 13 Slave 14 Slave 15...
  • Page 10 interface de昀椀nition DIAGRAM OF THE COMMUNICATION INTERFACE RS232 communica琀椀on port de昀椀ni琀椀on: INTERFACE DEFINED DECLARATION PIN 1 NC (empty) PIN 2 NC (empty) PIN 3 TX protec琀椀on board sends data (computer receiving data foot) RJ12, RS232 pin layout PIN 4 RX protec琀椀on board receives data (computer sends data) PIN 5 Ground signal ground...
  • Page 11 RS485-2 COMMUNICATION INTERFACE DEFINITION: INTERFACE DEFINED DECLARATION DEFINED DECLARATION PIN 1 RS485-B2 PIN 1 RS485-B2 PIN 2 RS485-A2 PIN 2 RS485-A2 PIN 3 RS485-GND PIN 3 RS485-GND Ba琀琀ery A part B part PIN 4 NC (empty) PIN 4 NC (empty) link ports RS-485-2 RS-485-2...
  • Page 12 FUNCTIONS WARNING Interfacing or plugging in any 3rd party or non approved Hubble products or periphirals into the RS232 (serial) or RS485 (Ba琀琀ery Link) ports, can cause damage to the BMS and cause the BMS to malfunc琀椀on. This may also result in damaging the internal cells.

  • Page 13: Current Limiting Function

    OPTIONAL CLOUDLINK DEVICE The Hubble Cloudlink is an op琀椀onal add-on to the Hubble X and AM range of products. As long as the device is connected to Wi-Fi it will cloud, all ba琀琀ery and inverter data to our cloud-server, enabling users to remotely monitor their power system.
  • Page 14 PARALLEL FUNCTIONS PARALLEL (CASCADE) FUNCTION OF BATTERY PACKS When the ba琀琀ery packs are cascaded, the one with the communica琀椀on address of 0001 is called the master ba琀琀ery pack, and the other ones with the communica琀椀on address are called the slave ba琀琀ery packs.
  • Page 15 warning TO ENSURE PROPER USE OF THE BATTERY PLEASE READ THE MANUAL CAREFULLY BEFORE USING IT. HANDLING Do not expose the ba琀琀ery to 昀椀re. Do not place the ba琀琀ery in a charger or equipment with wrong terminals connected. Avoid shor琀椀ng circui琀椀ng the ba琀琀ery . Avoid excessive physical shock or vibra琀椀on.
  • Page 16 COMPLETING SETUP CONGRATULATIONS! Once all the above steps have been completed you can proceed to follow the start-up instruc琀椀ons given by your inverter manufacturer. If you have any di昀케cul琀椀es with se琀�ng up your system, please contact our Technical Support Department via support@hubblelithium.co.za. Be sure to include the following informa琀椀on in your ini琀椀al email so that we can provide you with 琀椀mely assistance: 1.