• Wireless: Push and hold this button for 5 seconds to activate or deactivate wireless communication. • Manual Reset Option: Allows user to manually reset the statistics within the device to 0 without needing to use the Omega software. Any data recorded up to that point is recorded and saved. LED Indicators •...
“Wireless: OFF”. If wireless mode is on, press and hold the Wireless button on the device for 5 seconds. The OM-CP-RFPRHTEMP2000A comes with a USB cable. Plug one end of the cable into an available USB port on the PC and plug the opposite end of the cable into the communication port on the OM- CP-RFPRHTEMP2000A.
Page 4
Additional Features and Operation Alarm Settings/Rules In the Omega Software, alarms can be created on two levels; in the software itself, and programmed specifically to the data logger. Creating alarm rules in the software allows the user to utilize alarms while real time recording, and have the added benefit of features such as e-mail and SMS notification.
Troubleshooting Tips Why is the wireless data logger not appearing in the software? If the OM-CP-RFPRHTEMP2000A doesn’t appear in the Connected Devices panel, or an error message is received while using the OM-CP-RFPRHTEMP2000A, try the following: • Check that the OM-CP-RFC1000-EXT is properly connected. For more information, see Troubleshooting Interface Cable problems (below).
4. Push the cover closed until it clicks. Recalibration The OM-CP-RFPRHTEMP2000A standard calibration is one point at 25°C, two points at 25%RH and 75%RH and two points at 460 mbar and 1090 mbar. Recalibration is recommended annually for any Omega data logger; a reminder is automatically displayed in the software when the device is due.
Page 7
USB to mini USB, 250,000 baud for standalone operation or OM-CP-RFC1000- Computer Interface EXT required for wireless operation Software XP SP3/Vista/Windows 7/Windows 8 (Omega 4 Software only) -20°C to +60°C (-4°F to +140°F); 0%RH to 95%RH non-condensing Operating Environment 0.002 PSIA to 100 PSIA Dimensions 3.5”...
Page 8
WARNING: BATTERY MAY LEAK, FLAME OR EXPLODE IF DISASSEMBLED, SHORTED, CHARGED, CONNECTED TOGETHER, MIXED WITH USED OR OTHER BATTERIES, AND/OR EXPOSED TO FIRE/HIGH TEMPERATURE. DISCARD USED BATTERY PROMPTLY, KEEP OUT OF REACH OF CHILDREN. Specifications subject to change. See Omega’s terms and conditions at www.omega.com...
OM-CP-RFPRHTEMP2000A OM-CP-RFC1000-EXT Wireless Transceiver Other models available: OM-CP-RFC1000-EXT-EUR Approved for European markets OM-CP-RFC1000-IP69K Splash Proof for harsh environments...
Page 10
Note: To see if the .NET 4.0 Framework is installed, go to the Windows Control Panel and select Programs. “Microsoft .NET Framework 4.0” would be listed as a Windows program. 4. Select “Install Omega Software” if .NET framework is installed on the Windows PC, or if installing on a Windows 8 machine.
OM-CP-RFPRHTEMP2000A Mounting Instructions For best wireless performance, both the OM-CP-RFC1000-EXT and the Omega data loggers should be mounted in the same orientation. This usually means that the external antenna should be pointing straight up. The antenna can pivot to accommodate either a wall mount or a desk mount.
Different wireless channels may be used to create multiple networks in one area, or to avoid wireless interference from other devices. Any Omega data logger or OM-CP-RFC1000-EXT that is on the same network is required to use the same channel. If all of the devices are not on the same channel, the devices will not communicate with one another.
Page 13
Verify that the data loggers are in wireless transmission mode. (See Channel Programming steps above) On a Windows PC, launch the Omega data logger software program. All active data loggers will be listed in the software showing that the device(s) are recognized.
Page 14
Troubleshooting Tips Why is the wireless data logger not appearing in the software? If the OM-CP-RFPRHTEMP2000A doesn’t appear in the Connected Devices panel, or an error message is received while using the OM-CP-RFPRHTEMP2000A, try the following: • Check that the OM-CP-RFC1000-EXT is properly connected. For more information, see Troubleshooting Interface Cable problems (below).
Page 15
OM-CP-RFPRHTEMP2000A OM-CP-RFC1000-EXT General Specifications Interface Type USB (to PC) / Wireless (to Data Logger) Operating Environment -20°C to +85°C, 0%RH to 95%RH non-condensing LED Indicators Red & Green Enclosure Materials ABS Plastic (body), PVC Plastic (antenna) Dimensions Enclosure: 3.8” x 1.6” x 0.8” / Antenna: 7.2”...
OM-CP-RFPRHTEMP2000A Compliance Information • “This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.”...
Page 17
Fax: (203) 359-7700 e-mail: info@omega.com For Other Locations Visit omega.com/worldwide The information contained in this document is believed to be correct, but OMEGA accepts no liability for any errors it contains, and reserves the right to alter specifications without notice. WARRANTY/DISCLAIMER OMEGA ENGINEERING, INC.