Table of Contents
Advertisement
Quick Links
BRAVO
BRAVO-FUNK+ 915
USER MANUAL
MANUEL DE L'UTILISATEUR
This manual, including all its parts, and all the instructions contained in it must be read carefully and understood
before each installation, use, maintenance or reparation of the ELCA radio remote control.
Ce manuel, y comprises toutes les parties qui le composent, et toutes les instructions y contenues doivent être
lus attentivement et comprises avant toute opération d'installation, utilisation, entretien ou réparation de la
radiocommande ELCA.
OTHER LANGUAGES
https://qrcode.elcaradio.biz/man/751d329b511fd3d4b4934de51c4b16ed
BRAVO_FUNK+_915_00_EN_FR
0408MA001356
Advertisement
Table of Contents
Related Manuals for ELCA BRAVO
Summary of Contents for ELCA BRAVO
- Page 1 This manual, including all its parts, and all the instructions contained in it must be read carefully and understood before each installation, use, maintenance or reparation of the ELCA radio remote control. Ce manuel, y comprises toutes les parties qui le composent, et toutes les instructions y contenues doivent être lus attentivement et comprises avant toute opération d'installation, utilisation, entretien ou réparation de la...
- Page 3 Instructions translated from the original This manual, including all its parts, and all the instructions contained in it must be read carefully and understood before each installation, use, maintenance or reparation of the ELCA radio remote control. OTHER LANGUAGES https://qrcode.elcaradio.biz/man/751d329b511fd3d4b4934de51c4b16ed...
- Page 5 DEATH AND/OR DAMAGE TO PROPERTY. For further assistance CONTROL. refer to this Manual and all its parts, or else contact Elca. Elca is not responsible for and accepts no liability for any FAILURE TO READ THE MANUAL AND COMPLY WITH ALL THE...
-
Page 6: Table Of Contents
INDEX 1 Use and Maintenance Manual ............5 12.9 Battery introduction ............20 1.1 Structure .................. 5 12.10 Disposal of batteries ............20 1.2 Definitions ................5 13 Description of the Receiving Unit ..........21 1.3 Symbols .................. 5 13.1 Technical data ..............21 1.4 Who these instructions are for .......... -
Page 7: Use And Maintenance Manual
The Instruction manual for use and maintenance is an integral part understand these parts could be dangerous for Persons and/or of the Elca Radio Remote Control and therefore of the Machine that property. is equipped with the Radio Remote Control. It is the responsibility... -
Page 8: Intellectual Property
The Manufacturer of the Machine or whoever intends to use or will not occur in a particular installation. install an Elca Radio Remote Control on a Machine should first of all: If this equipment does cause harmful interference to radio or •... -
Page 9: Risk Analysis For Remote-Controlled Machines
• technical assistance for the Elca Radio Remote Control carried • FOR IMPLEMENTING ALL THE NECESSARY OR ADVISABLE out by a company other than Elca or that is not part of its MEASURES FOR REDUCING OR ELIMINATING THE RISKS assistance network. -
Page 10: Delay In The Command Response Time
Receiving Unit (see paragraph 7.3 ). 8.1 Characteristics • additional measures might be needed to protect the actuators An Elca Radio Remote Control of the BRAVO series belongs to a (see paragraph 7.4 ). family of industrial Radio Remote Controls, that can mainly be •... -
Page 11: Technical Data Of The Range
8.6 Applications The stop function using the Radio Remote Control is only An Elca Radio Remote Control of the BRAVO range can be used for available if the Radio Remote Control has been started. various applications: the suitability of the Radio Remote Control for each different application, especially for safety reasons, should be assessed by the Manufacturer of the Machine. -
Page 12: Classification Of The Controls
Radio Remote Control is installed; • the warnings and the instructions in this Manual and in other In addition to the above, a BRAVO Radio Remote Control should not be installed: documentation of the Radio Remote Control and the Machine fitted with the Radio Remote Control;... -
Page 13: Environmental Conditions Of Use
• use the Machine on which the Elca Radio Remote Control is 9.4 Warnings before starting work installed only in accordance with the measures and instructions provided by the Manufacturer of the Machine and in compliance all Before starting work with the Radio Remote Control the User applicable Laws, Regulations and Standards, also local;... -
Page 14: Belt
9.7 Belt The transmitting unit and the cable control unit are supplied with a belt. 9.7.1 Shoulder harness Assembly Before using the Radio Remote Control the User should connect the belt to the Transmitting Unit and/or the cable control unit, as described in the following procedure. -
Page 15: Description Of The Transmitting Unit
10 Description of the Transmitting Unit The User should use the belt with the Transmitting Unit and/or the cable control unit attached to prevent it falling or actuators accidentally being activated. The belt should be replaced if it show signs of wear or damage. Any other use of the belt constitutes the improper use of the control systems. -
Page 16: Technical Data
When the Red LED that indicates an error or Low Battery goes on, the transmitter emits a sound signal. 10.3 Transmitting Unit data plate The rating plate on the Transmitting Unit AT BRAVO-FUNK+ 915 contains information on: the serial number (Serial Num.), year of 10.4.2 LeD enable clamp... -
Page 17: General Operating Instructions
11 General operating instructions The radio remote control system BRAVO has been developed to ensure the best operating performance and has some special features outlined below. The symbols illustrated in this document are indicative and may vary. Refer to the specific documentation attached to the radio remote control. -
Page 18: Mechanical Starting Keyswitch
11.1 Mechanical starting keyswitch To restart working after the STOP button was pressed, proceed as follows: • check that the operating conditions are safe; • turn the STOP button in the direction indicated to disengage it; • carry out the procedure for starting the Radio Remote Control (see paragraph 11.5 ). -
Page 19: Selecting The Operating Mode
11.6 Selecting the operating mode When passing to Drilling with Loader operating mode, the automatic devices remain active. When none of the drilling modes are enabled, joysticks J1, J2, J3, J4 are disabled. 11.7.1 Gate open mode In Gate open mode, the joysticks from J2 to J4 run in slow mode, MODE while J1 does not run.The remaining joysticks run in normal mode. -
Page 20: Relationships Between Joysticks
11.8 Relationships between joysticks 11.13 Hammer Command The Hammer command is enabled with selector S26 (push-push command), and has two operating modes: • ON/OFF mode; Some Joysticks are placed in relation to each other and are: • Slow/ON/OFF mode. • J9 - J11 cannot perform both functions simultaneously and J11 In ON/OFF mode, an impulse enables the hammer command and an has priority over J9;... -
Page 21: Replacing The Transmitting Unit
12.1 Instructions for use Power unit LITE-ION USA Use only original Elca batteries and recharge them only with the Input 100-240Vac 50/60Hz 450mA Elca charging system. Do not use batteries showing external damage. -
Page 22: Battery Storage
12.4 Battery storage 12.7 Connection to the charging system Please note that a battery will self-discharge over time if not used; prolonged storage can also lead to a total and definitive loss of CLICK capacity, making the battery unusable. In order to ensure maximum battery life over time, the battery should be stored in a cool and dry environment if a long period of non-use is expected. -
Page 23: Description Of The Receiving Unit
The Radio Remote Control was evaluated for RF Exposure of portable devices. 13.2 Receiving unit data plate The rating plate on the cover of the Receiving Unit AR BRAVO- FUNK+ 915 contains information on: the serial number (Serial Num.), year of manufacture, main technical data on the Transmitting Unit and marking of the Radio Remote Control (see image in chapter 13 ). -
Page 24: General Operating Instructions
Failure to comply with these instructions can cause serious injuries or death and/or damage to property. 14 General operating instructions The receiving unit AR BRAVO-FUNK+ 915 consists of the following main circuits: • MOTHER BOARD • RADIO RECEIVING MODULE •... -
Page 25: Description Of Cable Control Unit
15 Description of cable control unit 15.2 Cable control unit data plate The rating plate on the cable control unit TEL BRAVO-FUNK+ contains information on: the serial number (Serial Num.), year of manufacture, main technical data on the cable control unit and marking on the cable control unit.
Need help?
Do you have a question about the BRAVO and is the answer not in the manual?
Questions and answers