Table of Contents
Advertisement
R3G310-FP12-31
3.2 Nominal data
Motor
M3G084-FA
Nominal voltage / VDC
48
Nominal voltage
36 .. 57
range / VDC
Method of obtaining
fa
data
Status
prelim.
Speed (rpm) / min
-1
2000
Power consumption / W
215
Current draw / A
4.4
Min. ambient
-40
temperature / °C
Max. ambient
40
temperature / °C
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change
3.3 Data according to Commission Regulation (EU) 327/
2011
01 Overall efficiency η
/ %
es
02 Measurement category
03 Efficiency category
04 Efficiency grade N
05 Variable speed drive
06 Year of manufacture
07 Manufacturer
08 Type
09 Power consumption P
/ kW
e
09 Air flow q
/ m³/h
v
09 Pressure increase total p
/
fs
Pa
10 Speed (rpm) n / min
-1
11 Specific ratio
*
12 Recycling/disposal
13 Maintenance
14 Additional components
*
Specific ratio = 1 + p
/ 100 000 Pa
fs
Data obtained at optimum efficiency level. The ErP data is determined using a motor-impeller
combination in a standardized measurement setup.
Item no. 57010-5-9970 · ENU · Change 215342 · Approved 2021-05-12 · Page 6 / 11
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
Operating instructions
Actual
Req. 2015
71.2
45.4
A
Static
87.8
62
Yes
The year of manufacture is specified on the
product's rating label.
ebm-papst Mulfingen GmbH & Co. KG
Amtsgericht (court of registration) Stuttgart ·
HRA 590344
D-74673 Mulfingen
R3G310-FP12-31
0.26
1805
329
1965
1.00
Information on recycling and disposal is
provided in the operating instructions.
Information on installation, operation and
maintenance is provided in the operating
instructions.
Components used to calculate the energy
efficiency that are not apparent from the
measurement category are detailed in the
CE declaration.
3.4 Technical description
Size
310 mm
Motor size
84
Rotor surface
Painted black
Electronics housing
Die-cast aluminum
material
Impeller material
PP plastic
Number of blades
6
Direction of rotation
Clockwise, viewed toward rotor
Degree of protection
IP42
Insulation class
"B"
Moisture (F) /
H1
Environmental (H)
protection class
Installation position
Any
Condensation
None
drainage holes
Mode
S1
Motor bearing
Ball bearing
Technical features
- Tach output
- Motor current limitation
- Soft start
- Control input 0-10 VDC / PWM
- Reverse polarity protection
Motor protection
Thermal overload protector (TOP)
internally connected
with cable
Variable
Conformity with
EN 62368-1; CE
standards
Approval
UL 1004-1; EAC; CSA C22.2 No. 100
With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.
; Use the device in accordance with its degree of protection.
Information on surface quality
The surfaces of the products conform to the generally applicable industrial
standard. The surface quality may change during the production period.
This has no effect on strength, dimensional stability and dimensional
accuracy.
The color pigments in the paints used perceptibly react to UV light over
the course of time. The product is to be protected against UV radiation to
prevent the formation of patches and fading. Changes in color are not a
reason for complaint and are not covered by the warranty. UV radiation
in the frequency range and the intensity of natural solar radiation has no
effect on the technical properties of the products.
3.5 Mounting data
Any further mounting data required can be taken from the product
drawing or Section Chapter 4.1 Mechanical connection.
Strength class of
8.8
screws
For screw clearance, see Chapter 3.1 Product drawing
; Secure the screws against unintentional loosening (e.g. use self-
locking screws).
Advertisement
Table of Contents
