Nominal Data; Technical Description; Mounting Data; Transport And Storage Conditions - ebm-papst R3G175-RG19-06 Operating Instructions Manual

R3G175-RG19-06

3.2 Nominal data

Motor M3G055-CF
Phase 1~
Nominal voltage / VAC 230
Nominal voltage 200 .. 240
range / VAC
Frequency / Hz
50/60
Method of obtaining ml
data
-1
Speed (rpm) / min 4200
Power consumption / W 115
Current draw / A
1.0
Min. ambient -25
temperature / °C
Max. ambient 60
temperature / °C
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change

3.3 Technical description

Weight 1.42 kg
Size 175 mm
Motor size
55
Rotor surface Thick-film passivated
Electronics housing Die-cast aluminum
material
Impeller material PA plastic
Number of blades 7
Direction of rotation Clockwise, viewed toward rotor
Degree of protection IP54
Insulation class
"B"
Moisture (F) / H1
Environmental (H)
protection class
Installation position Any
Condensation None, open rotor
drainage holes
Mode S1
Motor bearing Ball bearing
Technical features - Output 10 VDC, max. 10 mA
- Tach output
- Power limiter
- Motor current limitation
- Soft start
- Control input 0-10 VDC / PWM
- Control interface with SELV potential
safely disconnected from the mains
- Overvoltage detection
- Thermal overload protection for
electronics/motor
- Line undervoltage detection
Touch current <= 3.5 mA
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
Motor protection Electronic motor protection
Item no. 54740-5-9970 · ENU · Change 275730 · Approved 2023-01-27 · Page 6 / 12
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
Operating instructions
with cable
Protection class
assignment
Conformity with
standards
; Use the device in accordance with its degree of protection.
Information on surface quality
The surfaces of the products conform to the generally applicable industrial
standard. The surface quality may change during the production period.
This has no effect on strength, dimensional stability and dimensional
accuracy.
The color pigments in the paints used perceptibly react to UV light over
the course of time. The product is to be protected against UV radiation to
prevent the formation of patches and fading. Changes in color are not a
reason for complaint and are not covered by the warranty. UV radiation
in the frequency range and the intensity of natural solar radiation has no
effect on the technical properties of the products.

3.4 Mounting data

Further mounting data can be taken from the product drawing or Chapter
4.1 Mechanical connection as required.
Strength class of
screws
For screw clearance, see Chapter 3.1 Product drawing
; Secure the screws against unintentional loosening (e.g. use self-
locking screws).

3.5 Transport and storage conditions

Max. permitted
ambient temp. for
motor (transport/
storage)
Min. permitted
ambient temp. for
motor (transport/
storage)

3.6 Electromagnetic compatibility

EMC immunity to
interference
EMC circuit feedback
EMC interference
emission
Variable
I; If a protective earth is connected by
the customer
This component for installation may
have several local protection classes.
This information relates to this
component's basic design.
The final protection class is based on
the component's intended installation and
connection.
EN 60335-1; CE
8.8
+80 °C
-40 °C
According to EN 61000-6-2 (industrial
environment)
According to EN 61000-3-2/3
According to EN 61000-6-3 (household
environment)