Nominal Data; Technical Description; Mounting Data; Transport And Storage Conditions - ebm-papst D3G146-LU03-30 Operating Instructions Manual

D3G146-LU03-30

3.2 Nominal data

Motor M3G055-CF
Phase 1~
Nominal voltage / VAC 230
Nominal voltage 200 .. 240
range / VAC
Frequency / Hz
50/60
Method of obtaining fa
data
-1
Speed (rpm) / min 1300
Power consumption / W 95
Current draw / A
0.8
Min. back pressure / Pa 0
Min. ambient -25
temperature / °C
Max. ambient 55
temperature / °C
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change

3.3 Technical description

Weight 2.2 kg
Size
146 mm
Motor size 55
Rotor surface Galvanized
Electronics housing PP plastic
material
Impeller material PP plastic
Housing material PP plastic
Motor suspension Motor vibration-damped on both sides
Direction of rotation
Counterclockwise, viewed toward rotor
Degree of protection Motor IP00, electronics IP20; installation-
and position-dependent
Insulation class
"F"
Moisture (F) / H0 - dry environment
Environmental (H)
protection class
Installation position Any
Condensation None, open rotor
drainage holes
Cooling hole/opening On rotor and stator sides
Mode S1
Motor bearing Ball bearing
Technical features - Output 10 VDC, max. 1.1 mA
- Tach output
- Motor current limitation
- Soft start
- Control input 0-10 VDC / PWM
- Control interface with SELV potential
safely disconnected from the mains
- Thermal overload protection for motor
Touch current <= 3.5 mA
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
Electrical hookup
Plug
Item no. 53672-5-9970 · ENU · Change 230387 · Approved 2021-03-29 · Page 5 / 11
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
Operating instructions
Motor protection
with cable
Protection class
Conformity with
standards
Approval
; Use the device in accordance with its degree of protection.
Information on surface quality
The surfaces of the products conform to the generally applicable industrial
standard. The surface quality may change during the production period.
This has no effect on strength, dimensional stability and dimensional
accuracy.
The color pigments in the paints used perceptibly react to UV light over
the course of time. This does not however in any way affect the
technical properties of the products. The product is to be protected against
UV radiation to prevent the formation of patches and fading. Changes in
color are not a reason for complaint and are not covered by the warranty.

3.4 Mounting data

Any further mounting data required can be taken from the product
drawing or Section Chapter 4.1 Mechanical connection.
Strength class of
screws
For screw clearance, see Chapter 3.1 Product drawing
; Secure the screws against unintentional loosening (e.g. use self-
locking screws).

3.5 Transport and storage conditions

Max. permitted
ambient temp. for
motor (transport/
storage)
Min. permitted
ambient temp. for
motor (transport/
storage)

3.6 Electromagnetic compatibility

EMC immunity to
interference
EMC circuit feedback
EMC interference
emission
Thermal overload protector (TOP)
internally connected
Variable
I (with customer connection of protective
earth)
EN 60335-1; CE
EAC; CSA C22.2 No. 77 + CAN/CSA-
E60730-1; UL 1004-7 + 60730-1
With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.
8.8
+ 80 °C
- 40 °C
According to EN 61000-6-2 (industrial
environment)
According to EN 61000-3-2/3
According to EN 61000-6-3 (household
environment)