Nominal Data; Data According To Commission Regulation (Eu) 327/2011; Technical Description - ebm-papst G2D160-AF28-38 Operating Instructions Manual

Table of Contents

Advertisement

G2D160-AF28-38

3.2 Nominal data

Motor
M2D068-EC
Phase
3~
Nominal voltage / VAC
400
Wiring
Y
Frequency / Hz
50
Method of obtaining
ml
data
Valid for approval/
CE
standard
Speed (rpm) / min
-1
2480
Power consumption / W
225
Current draw / A
0.37
Min. back pressure / Pa
300
Min. ambient
-25
temperature / °C
Max. ambient
85
temperature / °C
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change
3.3 Data according to Commission Regulation (EU) 327/
2011
01 Overall efficiency η
/ %
es
02 Measurement category
03 Efficiency category
04 Efficiency grade N
05 Variable speed drive
06 Year of manufacture
07 Manufacturer
08 Type
09 Power consumption P
/ kW
e
09 Air flow q
/ m³/h
v
09 Pressure increase total p
/
fs
Pa
10 Speed (rpm) n / min
-1
*
11 Specific ratio
12 Recycling/disposal
13 Maintenance
14 Additional components
*
Specific ratio = 1 + p
/ 100 000 Pa
fs
Data obtained at optimum efficiency level. The efficiency values displayed for achieving
conformity with the Ecodesign Regulation EU 327/2011 has been reached with defined air
duct components (e.g. inlet rings). The dimensions must be requested from ebm-papst. If
other air conduction geometries are used on the installation side, the ebm-papst evaluation
loses its validity/the conformity must be confirmed again. The product does not fall within
the scope of Regulation (EU) 2019/1781 due to the exception specified in Article 2 (2a)
(motors completely integrated into a product).
Item no. 13192-5-9970 · ENU · Change 264594 · Approved 2022-08-09 · Page 5 / 11
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
Operating instructions
3~
480
Y
60
ml
CE
2820
365
0.48
400
-25
40
Actual
Req. 2015
32.9
32.5
A
Static
44.4
44
No
The year of manufacture is specified on the
product's rating label.
ebm-papst Mulfingen GmbH & Co. KG
Amtsgericht (court of registration) Stuttgart ·
HRA 590344
D-74673 Mulfingen
G2D160-AF28-38
0.15
360
505
2685
1.01
Information on recycling and disposal is
provided in the operating instructions.
Information on installation, operation and
maintenance is provided in the operating
instructions.
Components used to calculate the energy
efficiency that are not apparent from the
measurement category are detailed in the
CE declaration.

3.4 Technical description

Weight
4.18 kg
Size
160 mm
Motor size
68
Rotor surface
Painted black
Terminal box material
PP plastic
Impeller material
Sheet steel, galvanized
Housing material
Die-cast aluminum
Guard grille material
Hot-dip galvanized and spot-welded net
Direction of rotation
Clockwise, viewed toward rotor
Degree of protection
IP44; installation- and position-dependent
as per EN 60034-5
Insulation class
"F"
Moisture (F) /
H1
Environmental (H)
protection class
Installation position
Shaft horizontal or rotor on bottom; rotor
on top on request
Condensation
On rotor side
drainage holes
Mode
S1
Motor bearing
Ball bearing
Touch current
< 0.75 mA
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
Electrical hookup
Terminal box
Protection class
I; If a protective earth is connected by
assignment
the customer
This component for installation may
have several local protection classes.
This information relates to this
component's basic design.
The final protection class is based on
the component's intended installation and
connection.
Conformity with
EN 60034-1; EN 60204-1; EN 60335-1;
standards
CE
Approval
UL 1004-1; CSA C22.2 No. 100
With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.
; Use the device in accordance with its degree of protection.
Information on surface quality
The surfaces of the products conform to the generally applicable industrial
standard. The surface quality may change during the production period.
This has no effect on strength, dimensional stability and dimensional
accuracy.
The color pigments in the paints used perceptibly react to UV light over
the course of time. The product is to be protected against UV radiation to
prevent the formation of patches and fading. Changes in color are not a
reason for complaint and are not covered by the warranty. UV radiation
in the frequency range and the intensity of natural solar radiation has no
effect on the technical properties of the products.

Advertisement

Table of Contents
loading

Table of Contents