Using An Extension Cable - DeWalt D25032 Original Instructions Manual

hot during operation. Small bits of broken material may damage
bare hands.
• Never lay the tool down until the bit has come to a
complete stop. Moving bits could cause injury.
• Do not strike jammed bits with a hammer to dislodge
them. Fragments of metal or material chips could dislodge and
cause injury.
• Be certain that the material being drilled does not conceal
electric or gas service and that their locations have been
verified with the utility companies.
• Keep the power cord away from the rotating bit. Do not
wrap the cord around any part of your body. An electric cord
wrapped around a spinning bit may cause personal injury and loss
of control.
• When working above the floor, make sure that the area
below is clear. Falling parts can cause injuries to bystanders.
Reducing of Dust Exposure
Before starting work, check the hazard class of the dust that will
be produced when working.

WARNING: Dust can be harmful to health. Touching or
breathing of some dust created during the work process by using
a power tool and other construction activities contains chemicals,
minerals or particles known to cause respiratory infections, allergic
reactions, cancer, birth defects or other reproductive harm of the
user or bystanders.
• Such dusts can be generated, for example, when working on
hardwoods such as beech or oak, lead-based paint, on concrete,
masonry or stones containing quartz.
• Material containing asbestos may be handled only by specialists.
• Observe the relevant regulations in your country for the
materials to be worked on.
• Use a dust extractor or extraction system with an officially
approved protection class in compliance with the locally
applicable dust protection regulations and suitable for the
material to be worked on.
• Capture the resulting dust particles directly at the source and
avoid deposits in the surrounding area. Use suitable extraction
accessories for this purpose.
additional measures:
ʵ Make sure that the workplace is well ventilated.
ʵ Wear a respirator appropriate for the type of dust generated.
Residual Risks
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
• Impairment of hearing.
• Risk of personal injury due to flying particles.
• Risk of burns due to accessories becoming hot during operation.
• Risk of personal injury due to prolonged use.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the power supply corresponds to the voltage
on the rating plate.
Your D WALT tool is double insulated in accordance
e
with EN62841; therefore no earth wire is required.

WARNING: 115V units have to be operated via a fail-safe
isolating transformer with an earth screen between the primary
and secondary winding.
If the supply cord is damaged, it must be replaced by a
specially prepared cord available through the D
service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.

Using an Extension Cable

An extension cord should not be used unless absolutely necessary.
Use an approved extension cable suitable for the power input of
your charger (see Technical Data). The minimum conductor size is
1.5 mm 2 ; the maximum length is 30 m.
When using a cable reel, always unwind the cable completely.
Package Contents
The package contains:
1 Rotary hammer drill
1 Side handle
1 Depth adjustment rod
1 Keyless chuck (D25134, D25144)
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
a
Read instruction manual before use.
g
Wear ear protection.
f
Wear eye protection.
n
Visible radiation. Do not stare into light.
Date Code Position (Fig. A)
The production date code
12
by a 2-digit week and is extended by a 2-digit factory code.
Description (Fig. A, E, H)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Variable speed switch
1
Main handle
2
Forward/Reverse lever
3
Mode selector switch
4
Mode selector button
5
SDS plus® tool holder
6
EngLIsh
WALT
e
consists of a 4-digit year followed
23