Optional Accessory - DeWalt D25032 Original Instructions Manual

Setting the Drilling Depth (Fig. F)
1. Insert the required drill bit as described above.
2. Press the depth rod button
3. Fit the depth adjustment rod
depth stop clamp.
4. Adjust the drilling depth as shown.
5. Release the depth stop clamp.
Reversing Lever (Fig. G)
The forward/reverse lever 3
the hammer for backing out fasteners or jammed bits in the
drill-only function.

CAUTION: When reversing to clear jammed bits, be ready for
strong reactive torque.
To reverse the hammer, turn it off and align the forward/reverse
lever 3 with the yellow arrow pointing backward.
To position the lever for forward operation, turn the hammer
off and align the forward/reverse lever
pointing forward.
Fitting the Chuck Adapter and Chuck

Optional Accessory

D25032, D25033, D25133, D25143
1. Screw the chuck onto the threaded end of the chuck adapter.
2. Insert the connected chuck and adapter in the tool as though
it were a standard SDS plus® bit.
3. To remove the chuck, proceed as for removing a standard
SDS plus® bit.

WARNING: Never use standard chucks in the
hammerdrilling mode.
Replacing the SDS plus® Tool Holder with the Keyless
Chuck (Fig. H)
D25134, D25144
1. Turn the locking collar 13
pull the SDS plus® tool holder
2. Push the keyless chuck 14
locking collar to the locking position.
13
To replace the keyless chuck with the SDS plus® tool holder, first
remove the keyless chuck the same way the tool holder was
removed. Then place the tool holder the same way the keyless
chuck was placed, making sure to turn the locking collar to the
locking position.

WARNING: Never use standard chucks in the
hammerdrilling mode.
Replacing the Dust Cover (Fig. A)
The dust cover prevents dust ingress into the mechanism.
11
Replace a worn dust cover immediately.
1. Pull back the locking sleeve
cover 11 off.
2. Fit the new dust cover.
3. Release the locking sleeve.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power source
before making any adjustments or removing/installing
9 and keep it depressed.
through the hole in the
7
is used to reverse the rotation of
3 with the yellow arrow
into the unlocking position and
6 off.
onto the spindle and turn the
10 and pull the dust
attachments or accessories. Be sure the trigger switch is in the
OFF position. An accidental start-up can cause injury.

WARNING:
• Always observe the safety instructions and
applicable regulations.
• Be aware of the location of pipework and wiring.
• Apply only a gentle pressure to the tool (approx. 5 kg). Excessive
force does not speed up drilling but decreases tool performance
and may shorten tool life.
• Do not drill or drive too deep to prevent damage to the
dust cover.
• Always hold the tool firmly with both hands and ensure a
secure stance (Fig. I). Always operate the tool with the side handle
properly mounted.
Proper Hand Position (Fig. I)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
Proper hand position requires one hand on the side handle
with the other hand on the main handle
Switching On and Off (Fig. A)
1. To run the tool, press the variable speed switch
pressure exerted on the variable speed switch determines the
tool speed.
2. For continuous operation, press and hold down the variable
speed switch.
3. To stop the tool, release the switch.
Hammerdrilling (Fig. A)
Drilling with a Solid Bit
1. Hold down the mode selector button
selector switch 4 to the hammerdrilling position.
2. Insert the appropriate drill bit.
nOtE: For best results use high quality carbide-tipped bits.
3. Adjust the side handle 8
4. If necessary, set the drilling depth.
5. Mark the spot where the hole is to be drilled.
6. Place the drill bit on the spot and switch on the tool.
7. Always switch off the tool when work is finished and
before unplugging.
Drilling with a Core Bit
1. Hold down the mode selector button
selector switch to the hammerdrilling position.
4
2. Adjust the side handle 8
3. Insert the appropriate core bit.
4. Assemble the centerdrill into the core bit.
5. Place the centerdrill on the spot and press the variable
speed switch 1 . Drill until the core penetrates into the concrete
approx. 1 cm.
6. Stop drilling and remove the centerdrill. Place the core bit
back into the hole and continue drilling.
7. When drilling through a structure thicker than the depth of
the core bit, break away the round cylinder of concrete or core
inside the bit at regular intervals. To avoid unwanted breaking
away of concrete around the hole, first drill a hole the diameter
of the center drill completely through the structure. Then drill
the cored hole halfway from each side.
EngLIsh
.
2
. The
1
5 then set the mode
as required.
then set the mode
5
as required.
,
8
25