Table of Contents
Advertisement
Insert for liquid detergent
Position the insert for dispensing liquid detergent:
– Remove the detergent drawer completely
– Slide the insert forwards.
Do not use the insert (slide upwards):
– for gel detergents and washing powder,
– for programmes with
(Prewash) or the
Care
Machine housing, control panel
– Wipe with a soft, damp cloth.
– Remove detergent and cleaning agent residue immediately.
– Do not clean with a jet of water.
Cleaning the detergent drawer ...
... if it contains detergent or fabric softener residues.
1. Pull out, press insert down, remove drawer completely.
2. To remove the insert: press the insert upwards from below with your
finger.
3. Clean the detergent dispenser tray and insert with water and a brush and
dry it.
4. Fit the insert and engage (connect the cylinder to the guide pin).
5. Push in the detergent drawer.
Leave the detergent drawer open so that any residual water can
evaporate.
Drum
Leave the washing machine door open so that the drum can dry out.
Rust stains - use chlorine-free cleaning agent, not steel wool.
Descaling
Ensure there is no laundry in the machine
This should not be necessary if the correct detergent dosage has been used. If it is necessary,
however, proceed according to the descaling agent manufacturer's instructions. Suitable
descalers can be obtained via our website or from our after-sales service (
Information on the display panel
:
Close the washing machine door properly; laundry may be caught.
:
,
Open the tap completely, supply hose kinked or trapped; Clean the filter
page 11, water pressure too low.
:
Detergent solution pump blocked; Clean the detergent solution pump
page 11.
Drainage hose/waste pipe blocked; Clean the drainage hose at the
siphon
:
Water in the base tub, appliance leaking. Call the after-sales service.
:
,
Washing machine door cannot be locked. Open the washing machine
door and close it with an audible "click"; switch the appliance off and on
again; set the programme and make your settings; start the programme.
:
,
,
Motor fault. Call the after-sales service.
Other displays
Switch off the appliance, wait for 5 seconds and switch it back on. If the
display appears again, call the after-sales service
model-dependent
page 10.
(Finish in) option
– Risk of electric shock. Disconnect the mains plug.
– Risk of explosion. No solvents.
depending on model
page 11.
Information about blockages
Detergent solution pump
Turn the programme selector to
1. Open and remove the service flap.
2. Take the drainage hose out of the retainer.
Remove the sealing cap, allow the detergent solution to flow out.
Push the sealing cap back on.
3. Unscrew the pump cover carefully (residual water).
4. Clean the interior, pump cover thread and pump housing (the impeller
in the detergent solution pump must be able to rotate).
5. Replace the pump cover and screw it on tightly. The handle points upright.
Replace the drainage hose in the holder.
6. Refit the service flap and close it.
To prevent unused detergent from flowing straight into the drain during the next wash:
Pour 1 litre of water into compartment II and start the
Drainage hose at the siphon
Turn the programme selector to
1. Loosen the hose clamp, remove the drainage hose carefully
(residual water).
2. Clean the drainage hose and siphon connecting piece.
3. Reattach the drainage hose and secure the connection with the hose
clamp.
page 13).
Filter in the water supply
Risk of electric shock
Do not immerse the AquaStop safety device in water (it contains an electric valve).
Reduce the water pressure in the supply hose:
1. Turn off the tap.
2. Select any programme (except for
3. Select START/STOP (Start/Pause). Let the programme run for
approximately 40 seconds.
4. Turn the programme selector to
Clean the filter:
5. Disconnect the hose from the tap.
Clean the filter with a small brush.
and/or for Standard and Aqua-Secure models:
Remove the hose from the rear of the appliance.
Remove the filter with pliers and clean.
6. Connect the hose and check for leaks.
page 13.
10
Risk of scalding
– Allow the detergent solution to cool down.
– Turn off the tap.
Off and disconnect the mains plug.
(Empty) programme.
Off and disconnect the mains plug.
(Spin)/
(Empty)).
Off. Disconnect the mains plug.
11
Hide quick links:
Advertisement
Chapters
Table of Contents
