Table of Contents
Advertisement
Quick Links
A
DCN24181
O
EDN19269
Rev.
EDN/DCN No
No.
106-03-003
取 扱 説 明 書
INSTRUCTION MANUAL
6882
0.5/1.0mm PITCH FPC/FFC Connector
2024/03/05
Y. Tsuruoka
2019/11/01
日付 Date
Prepared by
© 2024 KYOCERA Corporation
Series
S. Morita
Y. Mamba
発行者
Checked by
No. : 205-03-6882-001
N. Nakajima
確認者
承認者
Approved by
Y. Fujii
Advertisement
Table of Contents
Related Manuals for Kyocera 6882 Series
Summary of Contents for Kyocera 6882 Series
- Page 1 INSTRUCTION MANUAL 6882 Series 0.5/1.0mm PITCH FPC/FFC Connector DCN24181 2024/03/05 Y. Tsuruoka N. Nakajima EDN19269 2019/11/01 S. Morita Y. Mamba Y. Fujii Rev. 発行者 確認者 承認者 EDN/DCN No 日付 Date Prepared by Checked by Approved by © 2024 KYOCERA Corporation 106-03-003...
-
Page 2: Table Of Contents
4. その他の注意事項 OTHER CAUTIONS ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 8 4.1 フラックス上がりについて FOR FLUX WICKING ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 8 4.2 エンボス梱包品の取扱いについて FOR HANDLING PRODUCTS PACKAGED IN TAPE & REEL ꞏꞏ 8 5. 製品の保管及び管理 STORAGE MANAGEMENT ꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏꞏ 8 6882 SERIES INSTRUCTION MANUAL No. 205-03-6882-001 © 2024 KYOCERA Corporatio n 106-03-004... -
Page 3: 概要 Outline
Series 6882 is developed to meet the market trend of downsizing of applications and high speed transmission. This connector is a very small size so please do handling carefully. The cautions of handling for 6882 series are shown in below. 2．各部の名称 NAME OF EACH PART <アクチュエータ開放状態 （納品時の状態）＞... -
Page 4: 取り扱い上の注意 Precautions In Handling
When passing the connector in the reflow or manual soldering by soldering iron, please confirm the actuator is open. After the connector is mounted, please do not operate the actuator without a FPC inserted. 6882 SERIES INSTRUCTION MANUAL No. 205-03-6882-001 © 2024 KYOCERA Corporatio n... -
Page 5: Fpc の挿入について Inserting A Fpc
Please insert a FPC into the slot end of connector horizontally against the board in below. FPC は基板に対して水平方向にカードスロットの最奥部に当たるまで挿入して下さい。 Please insert a FPC into the slot end connector horizontally against the board. 6882 SERIES INSTRUCTION MANUAL No. 205-03-6882-001 © 2024 KYOCERA Corporatio n... - Page 6 When closing the actuator, apply the force on the center of the actuator as shown below so that the stress could be applied evenly right and left. Do not apply the force to the side end. 6882 SERIES INSTRUCTION MANUAL No. 205-03-6882-001 ©...
-
Page 7: Fpc の抜去について Removing A Fpc
Good Good ※アクチュエータ開放角度は 60°までを目安とし、さらに開く方向への荷重を加えないようにしてください。 Caution： Actuator opening angle must be 60 degrees at maximum, and any further load shall not be applied in the opening direction. 6882 SERIES INSTRUCTION MANUAL No. 205-03-6882-001 © 2024 KYOCERA Corporatio n 106-03-004 PAGE 6/8... -
Page 8: Fpc の屈曲について Flexion Of A Fpc
Please contact us when an FPC has to be bent repeatedly near the opening for FPC insertion. We will conduct evaluation tests according to conditions. 可能な限り長くしてください。 As long as possible コネクタ Connector 6882 SERIES INSTRUCTION MANUAL No. 205-03-6882-001 © 2024 KYOCERA Corporatio n 106-03-004 PAGE 7/8... -
Page 9: その他の注意事項 Other Cautions
Store connectors under normal temperature, normal humidity and no dust condition. When storing connectors out of the TAPE & REEL package (bare connectors), please do not apply pressure to contact tails. 6882 SERIES INSTRUCTION MANUAL No. 205-03-6882-001 © 2024 KYOCERA Corporatio n...