Panasonic HL-C211F5 Instruction Manual

keep this manual in a convenient place for quick reference.
This product is intended to detect the objects and does not have the control func-
tion to ensure safety such as accident prevention.
Do not use the product as a sensing device to protect human body.
The product was developed and manufactured for industrial use.
Before using the product, check the sensor head model and contents of packing.
package.
• 1 sensor head unit
• 1 Instruction manual
• Laser warning labels
1
HL-C211F5( ), HL-C211F5( )- displacement sensor head achieves ultra
high-speed and high-accurate measurement using linear image sensor as light
receiving element to be used on equipment that require high-speed operation with
high-accuracy.
setting.
2
-2014
-2014
GB : GB 7247.1
-2012
-2013
FDA :
table).
*1
I IIa II IIIa
Performance (all laser products)
*2 *2 *2 *2
*3,4 *3,4 *3,4 *3,4
Performance (laser system)
S S S S
S S S S
S S S S
Labeling (all laser products)
D *5 *5 *5 *5
*6 *7
Information (all laser products)
NP : Not permitted
D : Depends on level of inner radiation
needed for product to perform its functions.
thus gained is not always necessary when housing is opened.
protective housing.
*6 : Warning statement label
-2 -2
.
Warning / Aperture label
-
Install the product so the laser beam comes higher or lower than eye level in or-
der not to watch the beam directly during operation.
Laser safety distance (Nominal Ocular Hazard Distance: NOHD) is approx. 0.5m. The
Please contact our company if the system breaks down. It is not equipped with a func-
tion that stops laser radiation automatically during disassembling the sensor head.
The users therefore may be exposed to laser beam in disassembling the sensor head.
3
HL-C211F5 and are subject to export control regulation by the
Foreign Exchange and Foreign Trade Law. Export admission by Japanese govern-
ment is required before the product is to be exported or brought out of the country.
These products are also subject to Article 1.B.3.b.1 of Nuclear Suppliers Group in
international export control regime and 2.B.6.b.1 of Wassenaar Arrangement.
Please follow the export control regulations required.
and (E type) are not subject to export control reg-
ulations under the condition that they are used combined with the non-pertinent
When they are combined with the pertinent controller to export control, they are
subject to the Law. In this case export admission by Japanese government is re-
quired before the product is to be exported or brought out of the country.
4
HL-C211F5( )
IIIb
110mm 106.7mm
*2 *2
±15mm ±14.5mm
*3,4 *3,4
Beam source
Beam diameter (Note 4) Approx. ø
Beam receiving element Linear image sensor
Linearity
*10 *10
Temperature characteristics
*13 Laser emission Green LED: Lights up during laser emission.
Yellow LED: Near measurement center:ON, within measurement range:Blink, beyond the range:OFF
S S
Protective structure IP67 (except connector)
NP NP
Pollution degree
S *11 S *11
Insulation resistance
*5 *5
Impulse ±
*12 *12
X, Y, and Z directions for 2 hours
2
Shock resistance in X, Y, and Z directions for 3 times
Ambient illuminance (Note 6)
Ambient temperature
Ambient humidity
Ambient Height 2,000m or less
Extendible to 30m long maximum using the optional extension cable.
Weight Approx. 300g including cable weight
tance, object substance: white ceramic,, and digital measurement value.
2)
3)
not subject to "Foreign Exchange and Foreign Trade Law".
6) The variation in ambient illuminance is ±0.03%F.S. or less.
5
When connecting or disconnecting the connectors, be sure to hold the connector
area not to apply extra force to the cable.
Be careful not to touch terminals or to let foreign matter get in the connector after
disconnecting connectors.
Be careful not to apply force to around the connector of standard cable and ex-
tension cable. Do not bend the cables near connectors. Failure to do so causes
causes disconnection of the cable.
Wiring
(E type only)
voltage and power circuit lines. If it is necessary to run the cable in parallel with
them, shield it by running through a grounded electrical conduit.
Install the product as far away as possible from noise source such as high-voltage
lines, high-voltage device, power lines, power device, machines which generate a
large starting and stopping surge, welding machines and inverter motor.
Do not pull the cable using a force more than
head and controller fixed. At least 20 mm is
required from the cable connection to the bend.
The bending radius must be 30 mm or more.
When the sensor head is moved around while
in use, the cable in the moving part may be
damaged. Therefore, use an extension cable for
the moving part and, when the extension cable
is damaged, immediately replace it. Otherwise, it
may result in failure.
between one sensor head and a controller.
When the sensor head part is moved around
while in use, fix the extension cable at a
position 100 mm away from the mobile end.
Allow at least 30 minutes of warming up after turning on the power to ensure the
performance of the product.
The life of the semiconductor laser depends on the ambient temperature during
use. When using the product near a heat source, take measures to lower the am-
having good heat radiation because the sensor itself emits heat.
Notes: 1) When installing 2 sensor heads in parallel at a 20mm or less interval, mount each sensor head on an alumi-
num or iron plate having a 200cm
ing paper.
Install the sensor head so ambient light such as sunlight or light with the same
wavelength as laser beam should not enter the light receiver. If high accuracy is
required, install a light shielding plate or the like on the sensor head.
The controller and connectors are not structurally dustproof, waterproof, or corro-
HL-C211F5( )
sion-resistant. Do not use the product underwater or in the rain.
110mm 106.7mm
gases, droplet, direct sunlight, severe vibration or impact.
±15mm ±14.5mm
The initial values of "Analog Scaling" after initialization is set to the following val-
±0.03%F.S.
2
6
0.5m
the center of limited measurement range.
-
2 (approximately 13.5%)
7
When installing 2 or more sensor heads side
by side, mutual interference occurs if the laser
spots from other sensor heads fall within the
heads so the laser spots from other sensor
heads fall outside the shaded areas.
8
20mm or more
HL-C211F5( )
Bending end
HL-C211F5( )
Line spot type
Fixing position
9
100mm or more
2 surface area.
-
10
received light intensity to an optimum level. This is useful when mounting the sen-
OFF Blink ON Blink OFF
distance
Panasonic Industry Co., Ltd.
1006, Oaza Kadoma, Kadoma-shi, Osaka 571-8506, Japan
https://industry.panasonic.com/
Please visit our website for inquiries and about our sales network.
Panasonic Industry Co., Ltd. 2024
April, 2024
0.24 0.24
0.2 0.2
1.2 1.7 2.2
0.2 0.2
Depth:10
(opposite surface)
Laser emission indicator
(green)
Light emission axis
Light range indicator
reception axis (yellow)
Beam Attenuator
Light emission axis
Light reception axis
Beam Attenuator
HL-C2F01) is optionally available to adjust the excessive
PRINTED IN JAPAN