Ferno TIROL KIT Series User And Maintenance Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

User and maintenance manual

TRANSLATION OF THE ORIGINAL INSTRUCTIONS

TIROL KIT

21-0120-023

XTREME TIROL KIT

21-00056

XTREME CONTROL TIROL KIT

21-00055

Tirol Kit Series

Read this manual

Rel.23022024English

carefully and keep it

for future reference

Table of Contents

Summary of Contents for Ferno TIROL KIT Series

Page 1 User and maintenance manual TRANSLATION OF THE ORIGINAL INSTRUCTIONS TIROL KIT 21-0120-023 XTREME TIROL KIT 21-00056 XTREME CONTROL TIROL KIT 21-00055 Tirol Kit Series Read this manual Rel.23022024English carefully and keep it for future reference...
Page 3: Table Of Contents
6.1.3 Installing the Adapter Kit for regular stretchers ___________________________________________________ 46 7. TECHNICAL SUPPORT ________________________________________________________________47 8. WARRANTY __________________________________________________________________________48 8.1 Warranty terms and conditions _________________________________________________________________ 48 8.2 Limitation of liability ________________________________________________________________________ 49 8.3 Warranty claims _____________________________________________________________________________ 49 8.4 Complaints ________________________________________________________________________________ 49 8.5 Return authorisations _________________________________________________________________________ 49 © Ferno S.r.l. Rel.23022024 ENG...
Page 4 Intellectual property declaration The information contained in this manual is the property of Ferno S.r.l. - Via Benedetto Zallone 26, 40066 Pieve di Cento (BO). All patent rights, design, construction, reproduction, use and sale rights relating to any item covered in this manual are the confidential and exclusive property of Ferno S.r.l., except for rights expressly transferred to third parties or not attributable to...
Page 5: Safety Information
Ferno S.r.l. Unauthorised repairs carried out by technicians Occasional assistants may cause damage and/or not approved by Ferno S.r.l. will render all physical harm, or injure themselves. Always keep warranties null and void and may compromise the the device under control, activate the controls, and safety of the device.
Page 7: Blood-Borne Diseases
The described accessories have been tested and validated for use with the listed basket stretchers. Ferno S.r.l. accepts no liability if accessories other than those listed are used. For more information, please refer to the user manual of the relevant product or contact your local distributor.
Page 8: Operator Training And Skills
Additional assistance may be needed to handle heavy patients and/or when the situation requires it and should always be provided according to local health care protocols. Read the user Two qualified operators are manual carefully recommended for correct use WARNING Make sure that all operators are trained and physically capable of handling loads. © Ferno S.r.l. Rel.23022024 ENG...
Page 9: Tirol Kit
3. TIROL KIT 3.1 Description The Tirol Kit rescue system is an accessory for Ferno's Titan basket stretchers, developed to facilitate rescue operations in difficult environments, making transportation safer. The Tirol Kit is designed for ease of use: it is lightweight and divisible.
Page 10 25-1607-001-01 (yellow and red) support Green and blue V-Shaped wheel 25-1608-001_01 (green and blue) support Wheel locking pin 25-1602-001 Tirol Kit Bag TIROL KIT BAG 10-00382 Threadlocker Presta /Schrader 10-00378 adapter for inflation valve with ring © Ferno S.r.l. Rel.23022024 ENG...
Page 11 25-1607-001-01 (yellow and red) support Green and blue V-Shaped wheel 25-1608-001_01 (green and blue) support Wheel locking pin 25-1602-001 Tirol Kit Bag TIROL KIT BAG 10-00382 Threadlocker Presta /Schrader 10-00378 adapter for inflation valve with ring © Ferno S.r.l. Rel.23022024 ENG...
Page 12 Green and blue V-Shaped wheel 25-1608-001_01 (green and blue) support Wheel locking pin 25-1602-001 Tirol Kit Bag TIROL KIT BAG Xtreme Control wheel 25-000156 Threadlocker 10-00382 Presta /Schrader adapter for inflation 10-00378 valve with ring © Ferno S.r.l. Rel.23022024 ENG...
Page 13: General Technical Specifications
For any further information, please visit: www.ferno.it 3.4 Reporting accidents In the event of a serious accident in relation to the device, immediately contact Ferno S.r.l. and the competent authority of the member State in which the user has its main office.
Page 14: Assembly
The fabric restraints are in good conditions, without cuts or signs of excessive wear. • The restraint buckles do not show visible damage and work correctly. WARNING Improper use of the device may cause damage and/ or injury. Use the device as indicated in this manual. © Ferno S.r.l. Rel.23022024 ENG...
Page 15: Toothed Shaft Assembly
Description Toothed shaft for the adjustment of 10-3001-4NP handles M8 screw with 16 mm Torx VTBTXM8X16A2 countersunk head M8 screw with 20 mm Torx VTBTXM8X20A2 countersunk head RPIM8X16A2 M8x16 flat washer x 16 10-00382 Threadlocker © Ferno S.r.l. Rel.23022024 ENG...
Page 16: Installing Toothed Shafts In Internal Configuration
Screw securely in place with a Torx T40 wrench. VTBTXM8X16A2 SHAFT IN INNER RPIM8X16A2 POSITION VTBTXM8X20A2 RPIM8X16A2 WARNING When mounting the toothed shafts in the inner position, ensure that they have the yellow lines facing upwards. © Ferno S.r.l. Rel.23022024 ENG...
Page 17: Installing Toothed Shafts In External Configuration
Screw securely in place with a Torx T40 wrench. VTBTXM8X20A2 VTBTXM8X16A2 TIROL KIT ADJUSTMENT SHAFT ON THE OUTER SIDE WARNING When mounting the toothed shafts in the outer position, ensure that they have the red lines facing upwards. © Ferno S.r.l. Rel.23022024 ENG...
Page 18: Toothed Shaft Assembly On Stretchers With Adapter Kit
Adapter Kit will be used: Images Part no. Description M8 screw with VTBTXM8X16A2 16 mm Torx countersunk head M8 screw with VTBTXM8X20A2 20 mm Torx countersunk head RPIM8X16A2 M8x16 flat washer x 16 © Ferno S.r.l. Rel.23022024 ENG...
Page 19 On stretchers that feature the Adapter Kit, the toothed shafts can only be mounted in the outer position. When mounting the toothed shafts in the outer position, ensure that they have the red lines facing upwards. © Ferno S.r.l. Rel.23022024 ENG...
Page 20: Handle Assembly
The device has been developed and tested for use with all the components indicated in this manual. Do not use the Tirol Kit without handles or other components that are essential for the correct use of the device. © Ferno S.r.l. Rel.23022024 ENG...
Page 21: Adjusting The Angle Of The Handles
A yellow line A yellow line with a dot YELLOW LINE WITH DOT YELLOW LINE These marks are intended to indicate the following suggested positions: • TRANSPORT POSITION • CPR / STATIONARY POSITION FOR PATIENT MANAGEMENT © Ferno S.r.l. Rel.23022024 ENG...
Page 22 (yellow line if the shaft is mounted on the inside or red line if it is mounted on the outside of the stretcher). © Ferno S.r.l. Rel.23022024 ENG...
Page 23: V-Shaped Support Assembly
Check that the V-Shaped wheel supports are correctly engaged and can rotate smoothly around the tube. Repeat this procedure on both sides of the stretcher. WARNING Do not install the quick-release systems of the V-Shaped supports at or near the vertical crossbars of the stretcher. © Ferno S.r.l. Rel.23022024 ENG...
Page 24: Wheel Assembly
Screw the pin in firmly and close the red locking lever. IMPORTANT If it is not possible to close the lever completely, slightly loosen the wheel locking pin until it can be properly secured. © Ferno S.r.l. Rel.23022024 ENG...
Page 25 REMOVING THE WHEEL To perform the correct procedure, proceed as described below: 1. Remove the pin. 2. Remove the wheel. 3. Disengage the V-Shaped wheel supports by pressing the red button at the quick-release system. © Ferno S.r.l. Rel.23022024 ENG...
Page 26: Wheel Assembly For Xtreme Control Tirol
Tighten the pin firmly to connect the two V-shaped supports and close the red locking lever. IMPORTANT If it is not possible to close the lever completely, slightly loosen the wheel locking pin until it can be properly secured. © Ferno S.r.l. Rel.23022024 ENG...
Page 27 Depending on the chosen position, the brake lever can be adjusted using the special positioning knob by loosening it, moving the brake lever to the chosen side and screwing it back in to secure it. BRAKE LEVER POSITIONING KNOB © Ferno S.r.l. Rel.23022024 ENG...
Page 28 - Cleaning the wheel (See section Cleaning the Xtreme Control wheel) - Adjusting the brake pads on Xtreme Control wheel (See section Brake pad adjustment on Xtreme Control wheel) © Ferno S.r.l. Rel.23022024 ENG...
Page 29 - Pulsed light - Light off When the light battery runs out, it can be easily recharged by unscrewing the upper part containing the LED and connecting the supplied cable to the micro USB port. © Ferno S.r.l. Rel.23022024 ENG...
Page 30 To remove the adapter, unscrew it from the valve, screw the cap back on and replace the adapter inside the light support by engaging the screw inside. Close the light support with the suitable cap. © Ferno S.r.l. Rel.23022024 ENG...
Page 31 Remove the wheel. Disengage the V-Shaped wheel supports by pressing the red button at the quick-release system. 4. Release the cable from the frame by releasing the clips. 5. Remove the brake lever from the handle. © Ferno S.r.l. Rel.23022024 ENG...
Page 32: Shoulder Support Application
Reconnect the 2 ends by re-attaching the “Cobra” buckle and adjust the length of the harness by pulling or loosening the end of the strap. © Ferno S.r.l. Rel.23022024 ENG...
Page 33: Maintenance
PERIODIC Maintenance: If there are signs of wear and damage, discontinue use of the stretcher and immediately contact Ferno S.r.l. Technical Support Service. Ferno S.r.l. directly carries out repair/maintenance operations, without the need of dealers, mechanics or external service centres.
Page 34: Disinfection/Decontamination
Wash at low temperature with detergent and use a gentle cycle. Do not use bleach or other aggressive products. Remove the Shoulder Supports from the bag and allow them to dry thoroughly. Do not put in dryer. © Ferno S.r.l. Rel.23022024 ENG...
Page 35: Cleaning The Xtreme Control Wheel
The device should be inspected regularly by maintenance personnel. Perform the various checks indicated in this manual. If signs of wear or damage are found during the inspection, stop using the device immediately and contact the Ferno S.r.l. Technical Support Service to request repairs/maintenance (see chapter on technical support).
Page 36: Lubrication
Adjust the brake calliper using a 4 mm Allen wrench (not supplied), working from both sides of the calliper. Once the operation has been carried out, reposition the casing and light support by re-tightening the six screws. © Ferno S.r.l. Rel.23022024 ENG...
Page 37: Accessories
Compatible with Titan-Ti and Tirol Kit all Tirol Kits and 10-2916-001 backpack harness DIVISIBLE TAPERED Titan basket stretchers Compatible with TIROL KIT BAG all Tirol Kits and Tirol Kit Bag Plus PLUS DIVISIBLE Titan basket stretchers © Ferno S.r.l. Rel.23022024 ENG...
Page 38 Tirol Kit ADAPTER See chapter 7.1 Adapter + 2 x 25-00099 for REGULAR Titan Kit. Basket Stretchers Compatible with all 25-00158 Xtreme wheel Tirol Kit models Contact Ferno to check 25-00132 Xtreme Control wheel compatibility © Ferno S.r.l. Rel.23022024 ENG...
Page 39: Adapter Kit
15 - no.2 Hexagon socket head cap screw UNI 5931 A4/80 M5x25. 16 - no.2 Hexagon socket head cap screw UNI 59531 A4/80 M8x50. 17 - no.4 Countersunk hexagon head socket cap screw ISO 10642 A4/70 M6x16. © Ferno S.r.l. Rel.23022024 ENG...
Page 40 Instructions To perform the correct procedure, proceed as described below: Join the two upper and lower plates “A”. Apply a drop of threadlocker to the threaded end of the two M5x25 hexagon socket head screws. © Ferno S.r.l. Rel.23022024 ENG...
Page 41 Apply 1 drop of threadlocker to the threaded end of the two M8x50 adjustment screws. Tighten them in the circled holes using the 6 mm Allen wrench until there is no more play between them. © Ferno S.r.l. Rel.23022024 ENG...
Page 42 NOTES: Maintain a gap of a few millimetres between the counter-plate and the lower plates. 10. Loosen the adjustment screws with the 6 mm Allen wrench so that the adapter plates of the Tirol kit are connected but play between them is still possible. © Ferno S.r.l. Rel.23022024 ENG...
Page 43 15. Loosen the adjustment screws with the 6 mm Allen wrench so that the plates of the Tirol Kit Adapter move away and adhere to the stretcher tubes. 16. Turn the stretcher in the direction of use. 17. Tighten the two M5x25 hexagon head screws securely. 18. Repeat the procedure on the foot end using plate “B”. © Ferno S.r.l. Rel.23022024 ENG...
Page 44 5. Before proceeding with steps 6-12, insert a shim (or two if necessary), between the plate assembly and the highest tube of the stretcher, before screwing the assembly back together. © Ferno S.r.l. Rel.23022024 ENG...
Page 45: Installing The Adapter Kit For Regular Stretchers
15 - no.2 Hexagon socket head cap screw UNI 5931 A4/80 M5x25. 16 - no.2 Hexagon socket head cap adjustment screw UNI 59531 A4/80 M8x50. 17 - no.4 Countersunk hexagon head socket cap screw ISO 10642 A4/70 M6x16. © Ferno S.r.l. Rel.23022024 ENG...
Page 46: Technical Support
• Fax: (+39) 0516861508 • Website: www.ferno.it For more information on the Ferno S.r.l. device, and to schedule training courses on its correct use, contact the Ferno S.r.l. Customer Service team. • Telephone: 800 501 711 (toll-free for Italy) •...
Page 47: Warranty
(lubricants, shoes, etc.), parts potentially exposed to oxidation or corrosion. Repairs are performed by trained technical staff at the Ferno S.r.l. site in Via Zallone 26- 40066 Pieve di Cento (BO), Italy or at the Customer's premises if suitable arrangements with Ferno S.r.l. Customer Service have been made.
Page 48: Limitation Of Liability
8.2 Limitation of liability If a product is found to be defective, Ferno S.r.l. will repair and replace it, or, at its own discretion, refund the purchase price. Under no circumstances can Ferno S.r.l. be held liable for a price higher than the selling price of the product.
Page 51 Product User and Maintenance Manual, required to operate the product safely, maintain its efficiency and reliability, and ensure compliance with the terms of the warranty. Rel.23022024English Ferno S.r.l. Ferno s.r.l., Pieve di Cento, Subsidiary of Savosa Via Benedetto Zallone 26 Via Tesserete, 67 40066 - Pieve di Cento (BO) - ITALY...

This manual is also suitable for:

Tirol kit Xtreme tirol kitXtreme control tirol kit21-0120-023 21-00056 21-00055

Ferno TIROL KIT Series User And Maintenance Manual

Quick Links

Related Manuals for Ferno TIROL KIT Series

Summary of Contents for Ferno TIROL KIT Series

This manual is also suitable for:

Table of Contents