Schmeiser Till An' Bedder-X Operation And Parts Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

RIGID 4-BAR

TILL AN' BEDDER

(X - GENERATION)

T. G. SCHMEISER

OPERATION AND PARTS

MANUAL

Version 3.1

September 2022

Read and understand the manual. This manual provides information and procedures to

safely operate and maintain the Folding 4-Bar Till An' Bedder.

Table of Contents

Need help?

Do you have a question about the Till An' Bedder-X and is the answer not in the manual?

Questions and answers

Summary of Contents for Schmeiser Till An' Bedder-X

Page 1 RIGID 4-BAR TILL AN’ BEDDER (X - GENERATION) T. G. SCHMEISER OPERATION AND PARTS MANUAL Version 3.1 September 2022 Read and understand the manual. This manual provides information and procedures to safely operate and maintain the Folding 4-Bar Till An’ Bedder.
Page 3: Table Of Contents
T. G. Schmeiser Co., Inc. 4-Bar Till An' Bedder-X CONTENTS INTRODUCTION............4 Operating Instructions with Secondary Unit Attached to Rear Trail Hitch......19 Engineered for Long Life........4 Towing Instructions..........19 Serial Number Information........4 Detaching from Tractor........19 Replacement Parts..........4 Initial Set Up Check List........20 Warranty Information..........4...
Page 4: Introduction
It is important that the Warranty Card be completed and T. G. Schmeiser Co., Inc. sent to Schmeiser. The warranty will not be valid until P.O. Box 1392 the information is on-file at Schmeiser. If information...
Page 5: Safety
. Improper operation and maintenance of this unit could result in a dangerous situation that could cause injury or death. T.G. Schmeiser cannot anticipate every possible circumstance that might involve a potential Indicates a potentially hazardous situation which, if hazard.
Page 6: Safety Icons Nomenclature
4-Bar Till An' Bedder-X T. G. Schmeiser Co., Inc. Safety Icons Nomenclature Hazard Avoidance SLOW VEHICLE PLACARD This manual and the equipment has numerous safety icons. BLOCK WHEELS SET PARKING BRAKE These safety icons provide important operating instructions CRUSHING HAZARD (body)
Page 7: General Safety
T. G. Schmeiser Co., Inc. 4-Bar Till An' Bedder-X GENERAL SAFETY To prevent injury, use a tractor equipped with a Roll Over Protective System (ROPS) . Read and Understand Manual Visually Inspect To prevent personal injury or even death, be sure...
Page 8: Towing Safety
4-Bar Till An' Bedder-X T. G. Schmeiser Co., Inc. TOWING SAFETY Be aware of physical surroundings and especially bystanders, particularly children, Unexpected Separation Hazard before moving the unit! This is particularly If the safety chain does not have a current...
Page 9: Highway And Transport Operations
T. G. Schmeiser Co., Inc. 4-Bar Till An' Bedder-X Highway and Transport Operations Enter And Exit Tractor SAFETY INSTRUCTIONS To avoid being run over, do not enter or exit Do not exceed a towing speed of more than tractor when it is moving . Avoid serious injury or 20 mph (32 KPH) on a public roadway .
Page 10: Tractor Safety Devices
4-Bar Till An' Bedder-X T. G. Schmeiser Co., Inc. Tractor Safety Devices If transporting or operating the tractor and implement Unexpected Separation Hazard near a public roadway, the tractor must be equipped If towing the unit with a drawbar, use only a...
Page 11: Maintenance Safety
T. G. Schmeiser Co., Inc. 4-Bar Till An' Bedder-X Explosive Separation Hazard High-Pressure Fluids 1 . Check or tighten all connections BEFORE Be sure all hydraulic pressure is relieved before pressurizing system . disconnecting hydraulic lines or fittings between implement and the tractor hydraulic system.
Page 12: Tires Safety
4-Bar Till An' Bedder-X T. G. Schmeiser Co., Inc. SAFETY INSTRUCTIONS Bolt Torque Requirements It is extremely important to apply and maintain proper Where replacement parts are necessary for torque on all bolts. Use a torque wrench to assure the periodic maintenance and servicing, genuine proper amount of torque is being applied to the fastener.
Page 13: Welding Repairs
Before performing any type of welding repair to the implement, contact T.G. Schmeiser Co., Inc. The T. G. Schmeiser implement has been designed for for approval. Repair welding must be done with care and the specific purpose of conditioning the ground in with procedures that may be beyond the capabilities of agricultural applications.
Page 14: Safety Marking And Lighting
4-Bar Till An' Bedder-X T. G. Schmeiser Co., Inc. SAFETY MARKING AND LIGHTING Part Number Description Q’ty GLT-LSDY Lamp, Surface Mount Double Yellow GLT-LSSR Lamp, Surface Mount Single Red D-2X9RY Reflective Tape, Yellow D-2X9RR Reflective Tape, Red D-2X9FL Fluorescent Tape, Orange GLT-FH30 Front Harness, 30 Ft.
Page 15: Safety Signs And Decals
T. G. Schmeiser Co., Inc. 4-Bar Till An' Bedder-X SAFETY SIGNS AND DECALS Safety Signs Item Part Number Description Qty. D48X038RTM Read the Manual D48X038CRR Crush / Rollover Hazard D48X064HPF High Pressure Fluids D28X048PPT Pinch Point D28X048RBW Transport Lockout D76X040SGB Transport Safety Chain —--------...
Page 16 4-Bar Till An' Bedder-X T. G. Schmeiser Co., Inc. D32X048RBC D52X272BLK Ph. (559) 268-8128 www.tgschmeiser.com Fax (559) 268-3279...
Page 17: Assembly And Operation
Wheel Axle. Connect Trunnion to two approximately 30’ x 30’ to assemble the Level Link Plates. Install spacer between Level SCHMEISER 4-Bar Rigid Till An’ Bedder. Link Plates. Refer to pp. 32-33 for reference. Unbolt Front Frame/Pull Frame/Trail Hitch Install Wheel Axle lockout systems in place.
Page 18: Attaching To Tractor
8 to 10 Adjusting the 4-Bar Rigid Till an’ Bedder-X hours. The Schmeiser 4-Bar Rigid Till an’ Bedder-X is a versatile Operating Instructions implement that can be configured for a variety of field conditions. Properly adjusted, it can be used to achieve a 1.
Page 19: Operating Instructions
T. G. Schmeiser Co., Inc. 4-Bar Till An' Bedder-X 4. Watch for low hanging limbs, power lines, and other ● Raise Till an’ Bedder last. Ensure that both lockouts overhead obstacles while you are operating. Use are properly seated on cylinders.
Page 20: Initial Setup Checklist
4-Bar Till An' Bedder-X T. G. Schmeiser Co., Inc. Initial Setup Checklist MAINTENANCE Efficient and safe operation of the implement requires that every user read and understand the operational instructions and all related safety instructions outlined in Understand Safety Procedures! this manual.
Page 21: Roller Rings
T. G. Schmeiser Co., Inc. 4-Bar Till An' Bedder-X Roller Rings Service Items Replace rings if they are excessively worn or damaged. Tires Check tire pressure and set to tire manufacturer’s recommended specifications. Inspect the tires for wear and/or damage. Make sure the wheel lugs are tightened...
Page 22: Maintenance Schedule
3. Inspect the frame for structural fractures and inspect Storage Preparation rings for excessive wear or damage. Replace if After 4-Bar Till An' Bedder-X field work is completed for needed. a season, perform the following maintenance procedures 4. Check all the bearings for signs of seal damage or before storing the implement.
Page 23: Placing In Storage
6. Make sure all the warning decals are in place and legible. Replace any damaged or missing decals. 2. Move the 4-Bar Till An' Bedder-X to a storage area with a firm and level base to prevent it from tipping or 7.
Page 24: Parts Section
4-Bar Till An' Bedder-X T. G. Schmeiser Co., Inc. COMPONENTS NOMENCLATURE Ph. (559) 268-8128 www.tgschmeiser.com Fax (559) 268-3279...
Page 25 T. G. Schmeiser Co., Inc. 4-Bar Till An' Bedder-X COMPONENTS NOMENCLATURE (Continue) Ordering Parts We manufacture a quality product that requires very little maintenance or repair. However, should a part break or become damaged, our knowledgeable staff can make sure you receive the part(s) to put your unit back into operation.
Page 26 4-Bar Till An' Bedder-X T. G. Schmeiser Co., Inc. Pull Frame Assembly Item Part Number Description Qty. TBX4-00J000 TBX Pull Frame GMB-HITCHCA3 CA 3 Perfect Hitch GHD-HHOLD1 Hose Holder Long GJK-5KTW15 Top Winding Jack Stand 5000# Capacity DTH-00H000 Front Turnbuckle Assembly CSNC520128 1-1/4”...
Page 27 T. G. Schmeiser Co., Inc. 4-Bar Till An' Bedder-X Front Frame Assembly Item Part Number Description Qty. FTB4-00D000 FTB4 Front Frame UBNF14128S 7/8” NF Square U-Bolt LWASHER-14 7/8” Lock Washer HXNUT-14NF 7/8” NF Hex Nut CSNC512032 3/4” X 2” Gr.5 Cap Screw LWASHER-12 3/4”...
Page 28 4-Bar Till An' Bedder-X T. G. Schmeiser Co., Inc. Main Frame Roller Leg and Roller Assembly Item Part Number Description Qty. FTB4-00J200 Roller Arm UBNF14128S 7/8” NC U-Bolt LWASHER-14 7/8” Lock Washer HXNUT-14NC 7/8” NC Hex Nut 212508 M18-2.5 X 70 mm Hex Head Bolt LWASHER-12 3/4”...
Page 29 T. G. Schmeiser Co., Inc. 4-Bar Till An' Bedder-X Roller Bearing Assembly Item Part Number Description Qty. / Roller Arm —------- Trunnion Bearing Assembly —------- Trunnion Hanger —------- Thrust Washer FTB4-00J203 Roller Arm Bearing Shim FTB4-00J200 Roller Arm 212508 M18-2.5 X 70 mm Hex Head Bolt LWASHER-12 3/4”...
Page 30 4-Bar Till An' Bedder-X T. G. Schmeiser Co., Inc. Ring / Roller Assembly 16/22 RING DIMENSIONS 14/20 RING DIMENSIONS 14/24 STEEL RING DIMENSIONS ROLLER O.D. ROLLER O.D. ROLLER O.D. Pipe Size Ring Size Ring Part No 12” 14/20 TPP3353D 12”...
Page 31 T. G. Schmeiser Co., Inc. 4-Bar Till An' Bedder-X S-Tine and S-Tine Tie Bar Assembly Item Part Number Description Qty. TBU-00K000 S-Tine Bar Hanger TBX4-14N101 S-Tine Bar for 14 Ft. Main Frame TBX4-16N101 S-Tine Bar for 16 Ft. Main Frame TBX4-20N101 S-Tine Bar for 20 Ft.
Page 32 4-Bar Till An' Bedder-X T. G. Schmeiser Co., Inc. Front to Rear Level System Assembly TO PULL FRAME TO WHEEL AXLE Item Part Number Description Qty. FTB4-00B100 Front to Rear Level Bar FTB4-00B200 Front to Rear Level Link DTH-00G300 Front to Rear Level Link Spacer...
Page 33 T. G. Schmeiser Co., Inc. 4-Bar Till An' Bedder-X Front to Rear Level Bar to Wheel Axle Connection Item Part Number Description Qty. —---------------- TBX4 Wheel Axle FTB4-00B100 Front to Rear Level Bar GHC-40160T 4” X 16” Tie Rod Hydraulic Cylinder...
Page 34 4-Bar Till An' Bedder-X T. G. Schmeiser Co., Inc. Wheel Axle Spindle and Hub Assembly 12 Ft. - 14 Ft. Units Item Part Number Description Q’ty TBU-02G016 2” X 23” Double Ended Spindle GHB-6X6GSL Grease Seal CR16289 GHB-6X6ICN Inner Bearing Cone...
Page 35 T. G. Schmeiser Co., Inc. 4-Bar Till An' Bedder-X Wheel Axle Spindle and Hub Assembly 16 Ft. - 20 Ft. Units Item Part Number Description Qty. GWT-121614 12.5 X 16 14 Ply Tire with Wheel Assembly FTB4-00M300 2-1/8” X 27-3/4" Removable Double Spindle...
Page 36 4-Bar Till An' Bedder-X T. G. Schmeiser Co., Inc. Wheel Axle Bearing Assembly Item Part Number Description Q’ty SLL1351 Bearing Cradle Cap SLL1350 1” Bearing Cap Casting UBNC16122R 1” NC Bearing U-Bolt HXNUT-16NC 1” NC Hex Nut LWASHER-16 1” Lock Washer...
Page 37 T. G. Schmeiser Co., Inc. 4-Bar Till An' Bedder-X Wheel Axle Cylinder Lockout System Assembly Item Part Number Description Qty. FTB4-00E100 Lockout Extension Tube Handle FTB4-00E200 Lockout Link FTB4-00E300 Lockout Bar CSNC512096 3/4” X 6” Gr.5 NC Cap Screw CSNC512072 3/4”...
Page 38 4-Bar Till An' Bedder-X T. G. Schmeiser Co., Inc. Rear Leveling Pipe Assembly Item Part Number Description Qty. FTB4-(00)M000 Leveling Pipe for Main Frame (specify size) TBX4-14N101 Lift Axle Bar for 14 Ft. Main Frame TBX4-16N101 Lift Axle Bar for 16 Ft. Main Frame TBX4-20N101 Lift Axle Bar for 20 Ft.
Page 39 T. G. Schmeiser Co., Inc. 4-Bar Till An' Bedder-X Rear Leveling Pipe Depth Indicator Assembly NOTE: Lift Axle Linkage Plate (item 4) and Depth Indicator Link Mount Bracket (item 6) are facing the same way. See drawing on p. 30 for all brackets orientations.
Page 40 4-Bar Till An' Bedder-X T. G. Schmeiser Co., Inc. S-Tine Depth Indicator Assembly NOTE: Depth Indicator Link Mount Bracket (item 6) is facing backwards when S-Tines are all the way down. See drawing on p. 30 for all brackets orientation.
Page 41 T. G. Schmeiser Co., Inc. 4-Bar Till An' Bedder-X Rear Trail Hitch Assembly (Optional) Item Part Number Description Qty. TBX4-00Q000 Rear Trail Hitch (Optional) GMB-HITCHCA3 Perfect Hitch CA3 CSNC512096 3/4” X 6” Gr.5 NC Cap Screw CSNC512032 3/4” X 2” Gr.5 NC Cap Screw LWASHER-12 3/4”...
Page 42: Hydraulic Diagrams
4-Bar Till An' Bedder-X T. G. Schmeiser Co., Inc. HYDRAULIC DIAGRAMS Wheel Axle Hydraulic Circuit Hose / Fitting Description Qty. Number Hose 8MP-8FJX 216” Long - Lead Hose Hose 8FJX-8FJX 170” Long FMBMJ9088 8MB-8MJ 90 Elbow FFP08000PT 8FP Pioneer Tips...
Page 43 T. G. Schmeiser Co., Inc. 4-Bar Till An' Bedder-X S-Tines Hydraulic Circuit Hose / Hyd. Line Description Qty. / Fitting Number Hose 8MP-8FJX 216” Long - Lead Hose Hose 8FJX-8FJX 28” Long Hose 8FJX-8FJX 30” Long FMBMJ9088 8MB-8MJ 90 Elbow...
Page 44 4-Bar Till An' Bedder-X T. G. Schmeiser Co., Inc. Leveling Pipe Hydraulic Circuit Hose / Fitting Description Qty. Number Hose 8MP-8FJX 216” Long - Lead Hose Hose 8FJX-8FJX 140” Long Hose 8FJX-8FJX 170” Long FMBMJ9088 8MB-8MJ 90 Elbow FFP08000PT 8FP Pioneer Tips...
Page 45 T. G. Schmeiser Co., Inc. 4-Bar Till An' Bedder-X Trail Hitch Hydraulic Circuit (Optional) Hose / Fitting Description Qty. Number Hose 8MP-8FJX 408” Long - Lead Hose FFP08000PT 8FP Pioneer Tips FMJMJH88 8MJ-8MJ Straight Bulkhead FHN88HN 8HN Bulkhead Nut FMPFJX88...
Page 46: Notes
4-Bar Till An' Bedder-X T. G. Schmeiser Co., Inc. NOTES Ph. (559) 268-8128 www.tgschmeiser.com Fax (559) 268-3279...
Page 47: Limited Warranty Statement
Except as set forth above, T . G . Schmeiser Co ., Inc . shall have no obligation or liability of any kind on account of any of its equipment and shall not be liable for special or consequential damages .
Page 48 Version 3.1 September 2022...

Schmeiser Till An' Bedder-X Operation And Parts Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Schmeiser Till An' Bedder-X

Summary of Contents for Schmeiser Till An' Bedder-X

Table of Contents