Table of Contents
Related Manuals for Schmeiser Bantam Leveler BOL 080
Summary of Contents for Schmeiser Bantam Leveler BOL 080
- Page 1 SCHMEISER BANTAM LEVELER T. G. SCHMEISER Co., Inc. OPERATION AND PARTS MANUAL Version 3.0 August 2019 Read and understand the manual. This manual provides information and procedures to safely operate and maintain the Bantam Leveler.
- Page 2 Copyright © 2019 T. G. Schmeiser Co., Inc. All rights reserved...
-
Page 3: Table Of Contents
T. G. Schmeiser Co., Inc. Bantam Leveler CONTENTS ASSEMBLY..............18 INTRODUCTION............4 Assembly Instructions.........18 Engineered for Long Life........4 Initial Setup Checklist.........20 Serial Number Information........4 Implement Break-In..........20 Replacement Parts..........4 Connecting to Tractor.........20 Warranty Information..........4 Detaching from Tractor........20 Serial Number Location.........4 Factory Contact Information........4 MAINTENANCE............21... -
Page 4: Introduction
_____________________________ Serial No. It is important that the Warranty Card be completed and _____________________________ Model No. sent to Schmeiser. The warranty will not be valid until _____________________________ Purchase Date the information is on-file at Schmeiser. If information not _____________________________ contained in this manual is needed, contact your Dealer Name Schmeiser dealer. -
Page 5: Specifications
T. G. Schmeiser Co., Inc. Bantam Leveler SPECIFICATIONS Approx HP Model Overall Width Dry Weight Weight w/Water BOL 080 8’6” (2.6 m) 2410 lbs (1093 kg) 3460 lbs (1569 kg) 40-50 BOL 090 9’6” (2.9 m) 2520 lbs (1143 kg) -
Page 6: Safety
. Indicates that equipment or property damage can result if instructions are not followed. T.G. Schmeiser cannot anticipate every possible circumstance that might involve a potential hazard. The SAFETY INSTRUCTIONS warnings in this manual and on the product are, therefore, not all-inclusive. -
Page 7: Safety Icons Nomenclature
T. G. Schmeiser Co., Inc. Bantam Leveler Safety Icons Nomenclature Hazard Avoidance SLOW VEHICLE PLACARD This manual and the equipment has numerous safety icons. BLOCK WHEELS SET PARKING BRAKE These safety icons provide important operating instructions CRUSHING HAZARD (body) which alert you to potential personal... -
Page 8: General Safety
Bantam Leveler T. G. Schmeiser Co., Inc. GENERAL SAFETY To prevent injury, use a tractor equipped with a Roll Over Protective System (ROPS) . Read and Understand Manual Visually Inspect To prevent personal injury or even death, be sure Visually inspect the unit for any loose bolts,... -
Page 9: Towing Safety
T. G. Schmeiser Co., Inc. Bantam Leveler TOWING SAFETY Be aware of physical surroundings and especially bystanders, particularly children, Unexpected Separation Hazard before moving the unit! This is particularly If the safety chain does not have a current important with higher noise levels and quiet cabs, as certification tag, do not use the unit until you may not hear people shouting . -
Page 10: Highway And Transport Operations
Bantam Leveler T. G. Schmeiser Co., Inc. Highway and Transport Operations Enter And Exit Tractor SAFETY INSTRUCTIONS To avoid being run over, do not enter or exit Do not exceed a towing speed of more than tractor when it is moving . Avoid serious 20 mph (32 KPH) on a public roadway . -
Page 11: Tractor Safety Devices
T. G. Schmeiser Co., Inc. Bantam Leveler Tractor Safety Devices If transporting or operating the tractor and implement Hydraulic Pressure near a public roadway, the tractor must be equipped This unit operates with hydraulic pressures of with proper warning lighting and a Slow Moving Vehicle 2500 to 3000 psi (170 to 205 bars) . -
Page 12: Maintenance Safety
Bantam Leveler T. G. Schmeiser Co., Inc. Explosive Separation Hazard High-Pressure Fluids Be sure all hydraulic pressure is relieved before 1 . Check or tighten all connections BEFORE disconnecting hydraulic lines or fittings between pressurizing system . implement and the tractor hydraulic system. -
Page 13: Tire Safety
T. G. Schmeiser Co., Inc. Bantam Leveler Where replacement parts are necessary for Bolt Torque Requirements periodic maintenance and servicing, genuine It is extremely important to apply and maintain proper factory replacement parts must be used to torque on all bolts. Use a torque wrench to assure the restore the unit to original specifications. -
Page 14: Welding Repairs
Before performing any type of welding repair to the implement, contact T.G. Schmeiser Co., Inc. The T. G. Schmeiser implement has been designed for for approval. Repair welding must be done with care and the specific purpose of conditioning the ground in with procedures that may be beyond the capabilities of agricultural applications. -
Page 15: Safety Marking And Lighting
T. G. Schmeiser Co., Inc. Bantam Leveler SAFETY MARKING AND LIGHTING SAFETY LIGHTING WIRING DIAGRAM FRONT OF MACHINE Item No Part No Description Q’ty GLT-LSDY Lamp, Surface Mount Double Yellow GLT-LSSR Lamp, Surface Mount Single Red D-2X9RY Reflective Tape, Yellow... -
Page 16: Safety Sign Placement
Bantam Leveler T. G. Schmeiser Co., Inc. SAFETY SIGN PLACEMENT Item No Part No Description Q’ty D48X038RTM Read the Manual D48X038CRR Crush / Rollover Hazard D48X064HPF High Pressure Fluids D28X048SCE Sharp Object Hazard D16X026GRS Grease Decal D28X048PPT Pinch Point D28X048RBW... -
Page 17: Safety Signs And Decals
T. G. Schmeiser Co., Inc. Bantam Leveler SAFETY SIGNS AND DECALS Follow all operating, maintenance, and safety Instructions found in this manual . Replace all worn or damaged safety and instruction decals . ● It is the responsibility of the customer to know the marking requirements of the local highway authorities and to comply with the regulations. -
Page 18: Assembly
Bantam Leveler T. G. Schmeiser Co., Inc. NOTICE ASSEMBLY Use connection to cylinder anchor for transportation only! 5. Move main frame over bucket. Connect bucket arms Understand Safety Procedures! to main frame with 3/4” x 4” bolts and nylon lock hex Read and understand all safety procedures nuts. -
Page 19: Initial Setup Checklist
T. G. Schmeiser Co., Inc. Bantam Leveler 14. Check all fasteners. Tighten if necessary. 9. Lift up bucket from center to insert threaded parts of cranks into trunnions. Screw in both sides evenly. Initial Setup Checklist Efficient and safe operation of the implement requires... -
Page 20: Implement Break-In
Bantam Leveler T. G. Schmeiser Co., Inc. Connecting to the Tractor Wheel Hub Bearings Re-pack with grease once a season – inspect bearings 1. Raise the jack stand until the tongue is at the height and races for wear and replace if necessary. -
Page 21: Wheel Hub Bearings
T. G. Schmeiser Co., Inc. Bantam Leveler Ground Engaging Components Service Items Bucket Blade Hydraulic Hoses Inspect all hydraulic hoses and fittings for leaks or signs Ground engaging components are subject to abrasion and wear. Excessively worn components will require of wear. -
Page 22: Maintenance Schedule
Bantam Leveler T. G. Schmeiser Co., Inc. Maintenance Schedule The period recommended is based on normal operating conditions. Severe or unusual conditions may require more frequent service. Hours and Serviced By Maintenance Before Each Use Ensure that all fasteners are tight, and all pins are secured in place. -
Page 23: Storage
T. G. Schmeiser Co., Inc. Bantam Leveler STORAGE 2. Move the Bantam Leveler to a storage area with a firm and level base to prevent it from tipping or sinking into the ground. For best results, always Storage Preparation store the Bantam Leveler in a dry, protected location. -
Page 24: Parts Section
Bantam Leveler T. G. Schmeiser Co., Inc. COMPONENT NOMENCLATURE Component Locations Ph. (559) 268-8128 www.tgschmeiser.com Fax (559) 268-3279... - Page 25 T. G. Schmeiser Co., Inc. Bantam Leveler Item No Part No Description SBL-00B000 Main Frame Weldment SBL-00A000 Tongue Weldment SBL-00J000 Hydraulic Cylinder Lockout GHC-40160T 4” x 16” Tie Rod Hydraulic Cylinder PMCK-34000 Seal Kit for 4” x 16” Tie Rod Hydraulic Cylinder...
-
Page 26: Ordering Parts
Bantam Leveler T. G. Schmeiser Co., Inc. Ordering Parts We manufacture a quality product that requires very little maintenance or repair. However, should a part break or become damaged, our knowledgeable staff can make sure you receive the part(s) to put your unit back into operation. -
Page 27: Wheel Axle Bearing Assembly
T. G. Schmeiser Co., Inc. Bantam Leveler Wheel Axle Bearing Assembly SEE NOTE Note: Ensure equal amount of space on each side before tightening U-bolts. Ensure equal number of threads on each side of U-Bolt. Item No Part No Description... -
Page 28: Wheel Axle Hub Assembly
Bantam Leveler T. G. Schmeiser Co., Inc. Wheel Axle Assembly Item No Part No Description SBL-00E000 Wheel Axle Weldment PTU-00P011 2" x 11" Single Ended Removable Spindle GHB-6X6GSL Grease Seal WHB-08X016 1/2" x 1" UNF Wheel Bolts for 6 on 6 Std. Hub GHB-6X6ICN Inner Bearing Cone for 6 on 6 Std. -
Page 29: Hydraulic Diagrams
T. G. Schmeiser Co., Inc. Bantam Leveler Hydraulic Diagram Note: All fittings are 3000 PSI Cap All hoses are 1/2” Ø Hydraulic Cylinder Part No Description GHC-40160T 4” x 16” Tie Rod Cylinder Fittings Item No Part No Description FMBMJ9088 MB-MJ 90°... -
Page 30: Notes
Bantam Leveler T. G. Schmeiser Co., Inc. NOTES Ph. (559) 268-8128 www.tgschmeiser.com Fax (559) 268-3279... -
Page 31: Limited Warranty Statement
Except as set forth above, T . G . Schmeiser Co ., Inc . shall have no obligation or liability of any kind on account of any of its equipment and shall not be liable for special or consequential damages . - Page 32 Version 3.0 August 2019...
Need help?
Do you have a question about the Bantam Leveler BOL 080 and is the answer not in the manual?
Questions and answers