Table of Contents
Related Manuals for Schmeiser CULTI PLOW 2-BAR
Summary of Contents for Schmeiser CULTI PLOW 2-BAR
- Page 1 SCHMEISER CULTI PLOW 2-BAR 3-BAR HD T. G. SCHMEISER Co., Inc. OPERATION AND PARTS MANUAL Version 2.0 August 2019 Read and understand the manual. This manual provides information and procedures to safely operate and maintain the CULTI PLOW.
- Page 2 Copyright © 2019 T. G. Schmeiser Co., Inc. All rights reserved...
-
Page 3: Table Of Contents
T.G. Schmeiser Co., Inc. CULTI PLOW CONTENTS Maintenance Schedule........18 INTRODUCTION............4 Engineered for Long Life........4 STORAGE..............19 Serial Number Information........4 Storage Preparation...........19 Replacement Parts..........4 Placing in storage..........19 Warranty Information..........4 Removing From Storage........19 Serial Number Location.........4 PARTS SECTION.............20 Factory Contact Information........4 Component Nomenclature........20 Dealer Contact Information........4... -
Page 4: Introduction
Selma, CA 93662 Warranty Information Phone: (559) 268-8128 It is important that the Warranty Card be completed and Fax: (559) 268-3279 sent to Schmeiser. The warranty will not be valid until E-mail: sales@tgschmeiser.com the information is on-file at Schmeiser. If information Web: www.tgschmeiser.com... -
Page 5: Specifications
T.G. Schmeiser Co., Inc. CULTI PLOW SPECIFICATIONS Model Overall Width Number of Shanks Weight Required HP 4CP1, 4CP3 4’-6” 413 lbs, 508 lbs 60-80 5CP1, 5CP3 5’-2” 438 lbs, 533 lbs 60-80 6CP1, 6CP3 6’-2” 463 lbs, 558 lbs 60-80 7CP1, 7CP3 7’-2”... -
Page 6: Safety
. Improper operation and maintenance of this unit could result in a dangerous situation that could cause injury or death. T.G. Schmeiser cannot anticipate every possible circumstance that might involve a potential Indicates a potentially hazardous situation which, if hazard. -
Page 7: Safety Icons Nomenclature
T.G. Schmeiser Co., Inc. CULTI PLOW Safety Icons Nomenclature Hazard Avoidance SLOW VEHICLE PLACARD This manual and the equipment has numerous safety icons. BLOCK WHEELS SET PARKING BRAKE These safety icons provide important operating instructions CRUSHING HAZARD (body) which alert you to potential personal... -
Page 8: General Safety
CULTI PLOW T.G. Schmeiser Co., Inc. GENERAL SAFETY To prevent injury, use a tractor equipped with a Roll Over Protective System (ROPS) . Read and Understand Manual Visually Inspect To prevent personal injury or even death, be sure Visually inspect the unit for any loose bolts,... -
Page 9: Operation Safety
T.G. Schmeiser Co., Inc. CULTI PLOW OPERATION SAFETY Highway and Transport Operations SAFETY INSTRUCTIONS Crush Hazard (Rolling Over) When transporting the implement on public Do not clean, lubricate, or make adjustments roads, use approved accessory lighting, flags, or while the unit is moving . -
Page 10: Tractor Safety Devices
CULTI PLOW T.G. Schmeiser Co., Inc. MAINTENANCE SAFETY Tractor Safety Devices If transporting or operating the tractor and implement near a public roadway, the tractor must be equipped Use Properly Rated Tools with proper warning lighting and a Slow Moving Vehicle... -
Page 11: Bolt Torque Requirements
Before performing any type of welding repair to torque on all bolts. Use a torque wrench to assure the the implement, contact T.G. Schmeiser Co., Inc. proper amount of torque is being applied to the fastener. for approval. Repair welding must be done with care and Start all bolts or nuts by hand to prevent cross threading. -
Page 12: Disposal Of Equipment At End Of Useful Life
T.G. Schmeiser Co., Inc. DISPOSAL OF EQUIPMENT AT END OF USEFUL LIFE The T. G. Schmeiser implement has been designed for the specific purpose of conditioning the ground in agricultural applications. When this unit is no longer capable of doing its designed purpose, it should be dismantled and scrapped. -
Page 13: Safety Marking And Lighting
T.G. Schmeiser Co., Inc. CULTI PLOW SAFETY LIGHTING AND MARKING 2-BAR CULTI PLOW 3-BAR HD CULTI PLOW FRONT OF MACHINE FRONT OF MACHINE LIGHTING DIAGRAM (FOR 3-BAR HD CULTI-PLOWS) Part Number Description Q’ty GLT-LSDY Lamp, Surface Mount Double Yellow GLT-LSSR... -
Page 14: Safety Signs And Decals
CULTI PLOW T.G. Schmeiser Co., Inc. SAFETY SIGNS AND DECALS SAFETY INSTRUCTIONS Follow all operating, maintenance, and safety Instructions found in this manual . Replace all worn or damaged safety and instruction decals . ● It is the responsibility of the customer to know the marking requirements of the local highway authorities and to comply with the regulations. -
Page 15: Safety Signs And Decals
T.G. Schmeiser Co., Inc. CULTI PLOW Safety Signs Item Part Number Description Qty. D28X048PPT Pinch Point D48X038RTM Read the Manual D48X038CRR Crush / Rollover Hazard D48X48QR Scan to Access Online Manual — FEMA D32X048RBC Made in the USA D32X208TGS Schmeiser (13”) -
Page 16: Assembly And Operation
CULTI PLOW T.G. Schmeiser Co., Inc. 2. After 10 hours of operation: ASSEMBLY AND OPERATION a. Go to the normal servicing and maintenance schedule, as defined in the Maintenance Section. Understand Safety Procedures! Read and understand all safety procedures Connecting to the Tractor described in this manual before performing any work on or around the implement. -
Page 17: Detaching From Tractor
T.G. Schmeiser Co., Inc. CULTI PLOW Ground Engaging Components Detaching From Tractor 1. Park the tractor, place the transmission in park or Shanks and Points neutral, and apply the parking brake. Shut down the engine, relieve all hydraulic pressure, and remove the Visually inspect shanks and points for wear and damage. -
Page 18: Maintenance Schedule
CULTI PLOW T.G. Schmeiser Co., Inc. Maintenance Schedule The period recommended is based on normal operating conditions. Severe or unusual conditions may require more frequent service. Copy this page to continue the record. Hours and Serviced By Maintenance Before Each Use Ensure that all fasteners are tight, and all pins are secured in place. -
Page 19: Storage
T.G. Schmeiser Co., Inc. CULTI PLOW STORAGE 2. Lower safety stand (if equipped), secure it in place with locking pin, and unhitch the implement from the tractor. Refer to “Detaching From Tractor” on page Storage Preparation After Culti Plow field work is completed for a season, 3. -
Page 20: Parts Section
CULTI PLOW T.G. Schmeiser Co., Inc. Ordering Parts We manufacture a quality product that requires very little maintenance or repair. However, should a part break or become damaged, our knowledgeable staff can make sure you receive the part(s) to put your unit back into operation. -
Page 21: 2-Bar Culti Plow Shank Assembly
T.G. Schmeiser Co., Inc. CULTI PLOW 2-Bar Culti-Plow Shank Assembly SINGLE SHANK (all CP1 models) DOUBLE SHANK (all CP3 models) 16 17 16 17 Q’ty / Shank Ass’y Q’ty / Shank Ass’y Item Part Number Description Shank, Chisel F-9 SCP0702... - Page 22 CULTI PLOW T.G. Schmeiser Co., Inc. 3-Bar Culti-Plow Assembly Item Part Number Description HD Culti Plow Main Frame (specify size) HCP-00P000 SCP0604 HD Culti Plow Frame Clamp Plate varies SCP0661-01 3-1/2” Tie Clamp Plate varies —-------------- Triple Shank Assembly (see p.
-
Page 23: 3-Bar Culti Plow Shank Assembly
T.G. Schmeiser Co., Inc. CULTI PLOW 3-Bar Culti-Plow Shank Assembly (Triple Shank) 15 14 Item Part Number Description Q’ty / Shank Ass’y Shank, Chisel F-9 SCP0702 SCP0703 Shank, Chisel B-8 SCP0704 Shank, Chisel T-8 SCP0721 Chisel Point, Regular SCP0663-01 4-1/2” Tie Clamp Plate CSNC512144 3/4”... -
Page 24: Gauge Leg Assembly (Optional)
CULTI PLOW T.G. Schmeiser Co., Inc. 3-Bar Culti-Plow Gauge Leg Assembly (Optional) Item Part Number Description Gauge Leg LH HCP-00P100L HCP-00P100R Gauge Leg RH HCP-00P300 HD Culti Plow Ratchet GHB-6X6GSL Grease Seal WHB-08X016 1/2" X 1” UNF Wheel Bolts for 6 on 6 Std. Hub GHB-6X6ICN Inner Bearing Cone for 6 on 6 Std. -
Page 25: Culti Plow Shank Quantities
T.G. Schmeiser Co., Inc. CULTI PLOW Culti Plow Shank Quantities Qty. Ref.# Part Number Description SCP0702 Shank, Chisel F-9 Chisel Point, Regular SCP0721 SCP0603 Culti Plow Frame Clamp Plate PBNC-08040 1/2" X 2-1/2" NC Plow Bolt LWASHER-08 1/2" Lock Washer HXNUT-08NC 1/2"... -
Page 26: Notes
CULTI PLOW T.G. Schmeiser Co., Inc. NOTES www.tgschmeiser.com Ph. (559) 268-8128 Fax (559) 268-3279... -
Page 27: Limited Warranty Statement
Except as set forth above, T . G . Schmeiser Co ., Inc . shall have no obligation or liability of any kind on account of any of its equipment and shall not be liable for special or consequential damages . - Page 28 Version 2.0 August 2019...
Need help?
Do you have a question about the CULTI PLOW 2-BAR and is the answer not in the manual?
Questions and answers