Table of Contents
Related Manuals for Schmeiser SMART-TILL ORCHARD MAX
Summary of Contents for Schmeiser SMART-TILL ORCHARD MAX
- Page 1 SCHMEISER SMART-TILL ORCHARD MAX T. G. SCHMEISER Co., Inc. OPERATION AND PARTS MANUAL Version 1.0 June 2019 Read and understand the manual. This manual provides information and procedures to safely operate and maintain the Mid Row Ripper.
- Page 2 Smart-Till Orchard Max T.G. Schmeiser Co., Inc. Ph. (559) 268-8128 www.tgschmeiser.com Fax (559) 268-3279...
-
Page 3: Table Of Contents
Safety Signs and Decals........13 SPECIFICATIONS............14 Tractor Requirements..........14 3-Point Hitch.............14 ASSEMBLY AND OPERATION........14 Attaching to Tractor..........14 Initial Set Up Check List..........15 Setting the Smart-Till Orchard Max......15 Adjusting the Smart-Till Orchard Max.....16 Implement Break-In..........17 General Operating Instructions......17 Detaching From Tractor........17 Ph. (559) 268-8128 www.tgschmeiser.com... -
Page 4: Introduction
It is important that the Warranty Card be completed and Web: www.tgschmeiser.com sent to Schmeiser. The warranty will not be valid until the information is on file at Schmeiser. If information not Additional copies of this manual can also be downloaded contained in this manual is needed, contact your at www.tgschmeiser.com. -
Page 5: Safety
. Improper operation and maintenance of this unit could result in a dangerous situation that could cause injury or death. T.G. Schmeiser cannot anticipate every possible circumstance that might involve a potential Indicates a potentially hazardous situation which, if hazard. -
Page 6: Safety Icons Nomenclature
Smart-Till Orchard Max T.G. Schmeiser Co., Inc. Safety Icons Nomenclature Hazard Avoidance SLOW VEHICLE PLACARD This manual and the equipment has numerous safety icons. BLOCK WHEELS SET PARKING BRAKE These safety icons provide important operating instructions CRUSHING HAZARD (body) which alert you to potential personal... -
Page 7: General Safety
T.G. Schmeiser Co., Inc. Smart-Till Orchard Max GENERAL SAFETY To prevent injury, use a tractor equipped with a Roll Over Protective System (ROPS) . Read and Understand Manual Visually Inspect To prevent personal injury or even death, be sure Visually inspect the unit for any loose bolts,... -
Page 8: Transport Safety
Smart-Till Orchard Max T.G. Schmeiser Co., Inc. OPERATION SAFETY Highway and Transport Operations SAFETY INSTRUCTIONS Crush Hazard (Rolling Over) Do not clean, lubricate, or make adjustments When transporting the implement on public while the unit is moving . roads, use approved accessory lighting, flags, or... -
Page 9: Tractor Safety Devices
T.G. Schmeiser Co., Inc. Smart-Till Orchard Max MAINTENANCE SAFETY Tractor Safety Devices If transporting or operating the tractor and implement near a public roadway, the tractor must be equipped Use Properly Rated Tools with proper warning lighting and a Slow Moving Vehicle... -
Page 10: Bolt Torque Requirements
1" 1320 USEFUL LIFE Welding Repairs The T. G. Schmeiser implement has been designed for the specific purpose of conditioning the ground in Before performing any type of welding repair to agricultural applications. When this unit is no longer the implement, contact T.G. Schmeiser Co., Inc. -
Page 11: Safety Marking And Lighting
T.G. Schmeiser Co., Inc. Smart-Till Orchard Max SAFETY MARKING AND LIGHTING WIRING DIAGRAM FRONT OF MACHINE Item Part Number Description Q’ty GLT-LSDY Lamp, Surface Mount Double Yellow GLT-LSSR Lamp, Surface Mount Single Red D-2X9RY Reflective Tape, Yellow D-2X9RR Reflective Tape, Red... -
Page 12: Safety Signs And Decals
Smart-Till Orchard Max T.G. Schmeiser Co., Inc. SAFETY SIGNS AND DECALS SAFETY INSTRUCTIONS Replace all worn or damaged safety and instruction decals . ● It is the responsibility of the customer to know the ● Make sure the safety signs and other instructional... -
Page 13: Safety Signs And Decals
T.G. Schmeiser Co., Inc. Smart-Till Orchard Max Safety Signs and Decals Item Part Number Description Qty. D48X038RTM Read the Manual D48X038CRR Crush / Rollover Hazard D28X048SCE Sharp Object Hazard D28X048PPT Pinch Point D32X208TGS Schmeiser 2” X 13” D104608BLK Schmeiser 6-1/2” X 38”... -
Page 14: Specifications
8. Extend or retract the 3-point top link to align its end category, certain size pins are used to attach the hole with the hole of the Smart-Till Orchard Max’s top implement to the tractor. CAT Il hitches require 1-1/8”... -
Page 15: Initial Setup Checklist
1. Use the adjustment on the tractor 3-point hitch lift arm to level the Smart-Till Orchard Max from side-to-side. 2. Adjust the top link to level the Smart-Till Orchard Max from front to back. Tine Gang Setting / Speed Chart... -
Page 16: Adjusting The Smart-Till Orchard Max
Adjusting the Smart-Till Orchard Max NOTICE Operating the Smart-Till Orchard Max with tine gangs at different angles can adversely affect the way the implement tracks and puts extra strain on the implement and tractor. Make sure all gangs are set to the same angle. -
Page 17: Implement Break-In
Smart-Till Orchard Max when used for the first time, it is recommended that the following mechanical items 8. Exit row by lifting the Smart-Till Orchard Max prior to be checked: passing the end post, but not so early as to neglect the final row. -
Page 18: Maintenance And Service
NOTICE on or around the implement. Tine gangs are directional and installed on the Smart-Till Orchard Max in a specific pattern. If tine NOTE: For service procedures Left-Hand and Right- gangs are removed or disassembled for any reason, Hand are referenced from the back of the always mark, reassemble, and reinstall in the same implement looking towards the tractor. -
Page 19: Replacing Tine Gang Bearings
4. Reinstall two new bolts and flanged nuts. It is Tine gangs are directional and installed on the Smart-Till Orchard Max in a specific pattern. If tine not recommended to reuse original tine gangs are removed or disassembled for any reason, hardware. -
Page 20: Ground Engaging Components
Smart-Till Orchard Max T.G. Schmeiser Co., Inc. 6. Slide the bearing off of the tine gang shaft. If the NOTICE bearing is seized on the tine gang shaft, use a two For best service life, always replace tine gang roller jaw puller to carefully remove it. -
Page 21: Maintenance Schedule
T.G. Schmeiser Co., Inc. Smart-Till Orchard Max Maintenance Schedule The period recommended is based on normal operating conditions. Severe or unusual conditions may require more frequent service. Copy this page to continue record. Hours and Serviced By Maintenance Before Each Use or Daily Ensure that all fasteners are tight, and all pins are secured in place. -
Page 22: Storage
6. Thoroughly wash the Smart-Till Orchard Max with a pressure washer or water hose to remove all dirt, 5. Attach the Smart-Till Orchard Max to the tractor 3- mud, or debris. point hitch. Refer to “Attaching to Tractor” on page 7. -
Page 23: Component Nomenclature
T.G. Schmeiser Co., Inc. Smart-Till Orchard Max COMPONENT NOMENCLATURE Component Locations Item Part Number Description Q’ty STO-14A000 Main Frame, 14 Ft. 853160 Gang LH Chrome 853161 Gang RH Chrome 3VB-E Clevis Pull Pin GBH-C23L01 CA 2-3 Lift Arm Bushing STO-00C000... -
Page 24: Parts Section
Smart-Till Orchard Max T.G. Schmeiser Co., Inc. Ordering Parts We manufacture a quality product that requires very little maintenance or repair. However, should a part break or become damaged, our knowledgeable staff can make sure you receive the part(s) to put your unit back into operation. -
Page 25: Chrome Tine Gang Assembly
T.G. Schmeiser Co., Inc. Smart-Till Orchard Max Chrome Tine Gang Assembly Q’ty/ Q’ty/ Item Part Number Description Item Part Number Description Gang Gang 853064 Left Top Carriage Plate (LH gang) 231262 Aerator Tine, LH Chrome (LH gang) 853160 Right Top Carriage Plate (RH gang) -
Page 26: Gang Roller Assembly
Smart-Till Orchard Max T.G. Schmeiser Co., Inc. Chrome Tine Gang Assembly Q’ty/ Item Part Number Description Gang Trunnion Bearing Assembly 553389 (Includes bearing, hangers, and thrust washers) 553390 Roller Thrust Plate 2.7 202270 5/8” X 1-1/2” Gr.5 NC Bolt LWASHER-10 5/8”... -
Page 27: Limited Warranty Statement
Except as set forth above, T . G . Schmeiser Co ., Inc . shall have no obligation or liability of any kind on account of any of its equipment and shall not be liable for special or consequential damages . - Page 28 Version 1.0 June 2019...
Need help?
Do you have a question about the SMART-TILL ORCHARD MAX and is the answer not in the manual?
Questions and answers