Table of Contents
Advertisement
en Ventilation function "Crisp Finish"
a When the time has elapsed, a signal sounds. A noti-
fication appears on the display confirming that the
operation has finished.
Once the cooking time has elapsed:
8.
If required, you can select other settings and re-
‒
start the operation.
When the food is ready, use
‒
pliance off.
If you have switched off the drying function for the
9.
microwave in the basic settings and condensation
has formed in the cooking compartment, dry the
cooking compartment.
→ "Drying function", Page 28
Note: If you open the appliance door during operation,
the operation stops. If you close the appliance door,
you must continue the operation. If you have changed
the basic setting for this, make sure that the microwave
does not resume operation without food inside.
→ "Basic settings", Page 23
Changing the microwave output setting
You can change the microwave output at any time.
Press the microwave output setting.
1.
Change the microwave output setting.
2.
Press "Apply".
3.
Changing the cooking time
You can change the cooking time at any time.
Press the cooking time.
1.
Change the cooking time using
2.
adjustment bar. Or enter the temperature directly via
the number field
.
Press "Apply".
3.
Ventilation function "Crisp Finish"
12 Ventilation function "Crisp Finish"
The ventilation function "Crisp Finish"
ture from the cooking compartment so that your meal
will be more crispy.
Hot steam that may escape when the appliance door is
opened is reduced.
12.1 Suitable types of heating with the
ventilation function
Only certain types of heating are suitable for the ventil-
ation function.
You can use the ventilation function for the following
types of heating:
¡ 4D hot air
¡ Top/bottom heating
¡ Pizza setting
¡ Circulated air grilling
12.2 Setting the ventilation function
You can activate the ventilation function at any time,
even after the start of the operation.
18
to switch the ap-
or
, or via the
extracts mois-
11.4 Setting added microwave
Note:
Note the correct way to operate the microwave:
¡ → "Safety", Page 2
¡ → "Preventing material damage", Page 6
¡ → "Microwave output settings", Page 11
¡ → "Cookware and accessories with microwave",
Page 16
Requirement: Observe the information about the re-
spective operating mode.
→ "Setting options with the microwave", Page 17
Press the operating mode that you require.
1.
Implement the settings for the operating mode, e.g.
2.
type of heating and temperature.
Press "Added microwave"
3.
Press the required microwave output setting.
4.
5.
Press "Cooking time" and set the cooking time.
Use
to start the operation.
6.
a The appliance starts to heat and the time counts
down.
a Once the cooking time has elapsed, a signal tone
sounds. A notification appears on the display con-
firming that the operation has finished.
Once the cooking time has elapsed:
7.
If required, you can select other settings and re-
‒
start the operation.
When the food is ready, use
‒
pliance off.
Changing added microwave
You can change or deactivate the added microwave at
any time.
Press the microwave output setting.
1.
Change or deactivate the microwave output setting.
2.
Press "Apply".
3.
Set a suitable type of heating and a temperature.
1.
If required, you can select other settings and com-
bine with the ventilation function.
Press "Crisp Finish".
2.
a "On" is in the tile.
Press
to start the operation.
3.
a The appliance starts heating.
a The setting values are shown on the display.
When the food is ready, use
4.
ance off.
Note: Amplified fan noises can be heard while the ap-
pliance is in operation.
Cancelling the ventilation function
You can switch off the ventilation function at any time.
Press "Crisp Finish"
▶
a For "Crisp Finish"
a The operation continues without the ventilation func-
tion.
.
to switch the ap-
to switch the appli-
.
, "Off" appears on the display.
Advertisement
Table of Contents
