Etekcity ZAP 1L-S, ZAP 1L-Rx, ZAP 1L-Tx - ZAP Remote Outlet Manual

Also See for ZAP 1L-S:

Manual (24 pages)

Table of Contents

Contents

1 Function Diagram
2 Operation
3 Troubleshooting
- 3.1 Outlet is unresponsive to remote commands
4 Specifications
5 Package Contents
6 Safety Information
7 Customer Support
8 Documents / Resources
- 8.1 References
- 8.2 Download manual

Etekcity ZAP 1L-S, ZAP 1L-Rx, ZAP 1L-Tx - ZAP Remote Outlet Manual

Function Diagram

Function Diagram - Part 1

Outlet
Power/Program Button
Outlet Indicator Light
Outlet Number

Function Diagram - Part 2

Remote
ON Buttons
OFF Buttons

Operation

The outlets are pre-programmed for immediate use, but the configuration can be customized to meet your needs.

Install one 12V (23A) battery in each remote control.

Plug each outlet into a powered socket.

Plug an appliance into each outl et. Make sure the appliance is switched to ON in order to allow the outlet to control the device.

Press the ON or OFF buttons for the corresponding outlet number on the remote. The indicator light on the corresponding outlet will turn on or turn off, confirming that the outlet is now in use.

Reprogramming an Outlet

Unplug device from outlet.

Press and hold program button until indicator light starts to blink.

Release program button, press the ON or OFF button for the desired number on the remote.

Pairing is successful when indicator light stops blinking.
NOTE: You may repeat the reprogramming steps to assign up to 10 outlets to a single number to simultaneously control multiple devices with a single click.

Resetting an Outlet
To remove an outlet from all remote control pairings:

Unplug any devices connected to the remote outlet.

Remove the outlet from the power socket.

Press and hold the program button.
Plug outlet back into power socket while continuing to hold program button.

Hold program button for approximately 5 seconds until LED indicator begins to flash.
Program reset will be complete when indicator light stops blinking.

Troubleshooting

Issue	Solution
Outlet is unresponsive to remote commands	Replace the remote batteries with new 12V (23A) batteries. Low battery power may decrease readable wireless remote range.
	Make sure the outlet and device are properly connected and powered on.
	Make sure that the outlet is placed in an area with proper air circulation to avoid overheating.
	Make sure the maximum load current of 10A (~1200W) isn't being exceeded. If so, unplug the device from the outlet immediately.
	If the outlet is still unresponsive, refer to the Resetting and Reprogramming sections in the manual.

Specifications

Voltage:	120V~60 Hz
Maximum Current:	10A
Maximum Power:	1200W
Transmission Frequency:	433.92 MHz
Remote Battery Power:	12V (23A)
Remote Control Range:	100 ft (30 m)*
Operating Temperature:	32°~95°F (0°~35°C)
Storage Temperature:	-4°~167°F (-4°~75°C)

*NOTE: The wireless range may be shortened by other electronic devices, appliances, walls, and other physical barriers.

Package Contents

ZAP 1L-S
1 x Remote Outlet
1 x Remote Control
1 x 12V (23A) Battery
1 x User Manual

ZAP 1L-Rx
1 x Remote Outlet
1 x User Manual

ZAP 1L-Tx
1 x Remote Control
1 x 12V (23A) Battery
1 x User Manual

Safety Information

Please read, understand, and comply with all of the instructions provided in this manual before using this device. Failure to comply with the instructions given in this manual and/or using the device in ways other than the ones mentioned herein may result in physical harm and/or damage to the device.

Important Safety Information

The wireless range may be limited by other electronic devices, appliances, walls, or other physical barriers.
The outlets are intended for indoor use only.
Avoid exposure to high-temperature sources, direct sunlight, or moisture.
Do not exceed the maximum load current of 10A (~1200W).

Do not use appliances such as refrigerators, air conditioning units, and washing machines with the outlets. Such appliances exceed the maximum load current of 10A (~1200W).
Keep out of reach of children.
The outlets are best used in areas with proper air circulation.
When cleaning, use a dry cloth to wipe the outlet and remote surfaces.
For your safety, make sure the batteries within the remotes are correctly installed before use.
Do not dispose of any part of this product in a fire.
The remote is not compatible with rechargeable batteries.
This device is not intended for use in areas with high humidity, such as bathrooms.
For best performance, regularly change the batteries in the remote controls.
If the remote is not in use for an extended period of time, remove batteries.
These outlets are not compatible with the ZAP 3VX remote outlets.

Customer Support

Should you encounter any issues or have any questions regarding your new product, feel free to contact our helpful Customer Support Team.
CUSTOMER SUPPORT
Etekcity Corporation
1202 N. Miller St., Suite A Anaheim, CA 92806
Email: support@etekcity.com
Toll-Free: (855) 686-3835 SUPPORT HOURS
Monday - Friday
9:00 am - 5:00pm PST/PDT
*Please have your order confirmation number ready before contacting customer support.

Scan here and join the community!
http://www.etekcity.com