Related Manuals for ETEKCITY ZAP 1L-S
Summary of Contents for ETEKCITY ZAP 1L-S
- Page 1 ZAP Remote Outlet Model Nos.: ZAP 1L-S ZAP 1L-Rx ZAP 1L-Tx Questions or Concerns? (855) 686-3835 support@etekcity.com...
- Page 3 Thank You. Thank you for purchasing the Remote Outlet by Etekcity. We are dedicated to providing our customers with quality products for building on better living. Should you have any questions or concerns about using your new product, feel free to reach out to our helpful Customer Support Team at...
-
Page 4: Table Of Contents
Table of Contents Safety Information Function Diagram Operation Reprogramming an Outlet Resetting an Outlet Troubleshooting Specifications Package Contents Warranty Information Customer Support... -
Page 5: Safety Information
Safety Information IMPORTANT: Please read, understand, and comply with all of the instructions provided in this manual before using this device. Failure to comply with the instructions given in this manual and/or using the device in ways other than the ones mentioned herein may result in physical harm and/or damage to the device. - Page 6 • Do not use appliances such as refrigerators, air conditioning units, and washing machines with the outlets. Such appliances exceed the maximum load current of 10A (~1200W). • Keep out of reach of children. • The outlets are best used in areas with proper air circulation. •...
-
Page 7: Function Diagram
Function Diagram 1. Outlet 2. Power/Program Button 3. Outlet Indicator Light 4. Outlet Number Front Back... - Page 8 5. Remote 6. ON Buttons 7. OFF Buttons...
-
Page 9: Operation
Plug each outlet into a powered socket. Operation The outlets are pre-programmed for immediate use, but the configuration can be customized to meet your needs. Install one 12V (23A) battery in each remote control. - Page 10 Press the ON or OFF buttons Plug an appliance into each et. Make sure the appliance for the corresponding outlet number outl is switched to ON in order to on the remote. The indicator light allow the outlet to control the on the corresponding outlet will turn on or turn off, confirming device.
-
Page 11: Reprogramming An Outlet
Reprogramming an Outlet Press and hold program button until indicator light starts to blink. Unplug device from outlet. Program Button... - Page 12 Release program button, press Pairing is successful when the ON or OFF button for the indicator light stops blinking. desired number on the remote. NOTE: You may repeat the reprogramming steps to assign up to 10 outlets to a single number to simultaneously control multiple devices with a single click.
-
Page 13: Resetting An Outlet
Resetting an Outlet Remove the outlet from the power socket. To remove an outlet from all remote control pairings: Unplug any devices connected to the remote outlet. - Page 14 Press and hold the program Hold program button for button. approximately 5 seconds Plug outlet back into power until LED indicator begins socket while continuing to to flash. hold program button. Program reset will be complete when indicator Program light stops blinking. Button...
-
Page 15: Troubleshooting
Troubleshooting Issue Solution Replace the remote batteries with new 12V (23A) batteries. Low Outlet is unresponsive battery power may decrease readable wireless remote range. to remote Make sure the outlet and device are properly connected commands. and powered on. Make sure that the outlet is placed in an area with proper air circulation to avoid overheating. -
Page 16: Specifications
Package Contents Specifications ZAP 1L-S 1 x Remote Outlet 1 x Remote Control 1 x 12V (23A) Battery Voltage: 120V~60 Hz 1 x User Manual Maximum Current: Maximum Power: 1200W Transmission Frequency: 433.92 MHz Remote Battery Power: ZAP 1L-Rx 12V (23A) - Page 17 FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
- Page 18 FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instructions as documented in this manual.
-
Page 19: Warranty Information
TERMS & POLICY Warranty Etekcity warrants all products to be of the highest quality in material, craftsmanship, Information and service effective from the date of purchase to the end of the warranty period. Etekcity will replace any product found to... - Page 20 This warranty is non-transferrable. limitation of incidental or consequential Etekcity is not responsible in any way for losses so the foregoing disclaimer may not any damages, losses, or inconveniences apply to you. This warranty gives you...
- Page 21 Defective Products & Returns Should your product prove defective within the specified warranty period, please contact Customer Support via support@etekcity.com with your invoice and order number. DO NOT dispose of your product before contacting us. Once our Customer Support Team has approved your request, please return the unit with a copy of your invoice and order number.
-
Page 22: Customer Support
Customer Support Team. Your satisfaction is ours! CUSTOMER SUPPORT SUPPORT HOURS Monday - Friday Etekcity Corporation 1202 N. Miller St., Suite A 9:00 am - 5:00pm PST/PDT Anaheim, CA 92806 Email: support@etekcity.com... - Page 24 Scan here and join the community! http://www.etekcity.com...