Schweigen Isodrive 900 Installation Manual
Hide thumbs
Also See for Isodrive 900:
- Installation manual (28 pages) ,
- Installation manual (24 pages)
Related Manuals for Schweigen Isodrive 900
Summary of Contents for Schweigen Isodrive 900
- Page 1 INSTALLATION GUIDE Isodrive 900 www.schweigen.co.nz www.schweigen.com.au 03/2024/V1 12.2016 / V1.0...
-
Page 2: Welcome
Welcome Thank you for purchasing your new Schweigen Isodrive system. To get the maximum output from this unit, please read through this guide before use and installation. This guide contains important information on the correct use and maintenance of the unit, as well as important safety notes. -
Page 3: Table Of Contents
Wall Installation ________________________________________________________________________________ 10 Flat Roof Installation ___________________________________________________________________________ 12 Through Wall Installation for Isodrive 900 _______________________________________________ 13 Fan Unit Shutter Assembly for Isodrive 900 (Optional) _____________________________________ 14 Twin 200mm Outlet Installation Example _______________________________________________ 15 5. Measurements Measurements for Isodrive 900 _________________________________________________________________ 16 6. -
Page 4: Your Safety
Children should be supervised to ensure that they do not play with the appliance, it is not a toy. Do not install Isodrive motor to a non-Schweigen and/or non-silent rangehood. If you fail to do so, your warranty will be voided. -
Page 5: Motor Features
Recommended Installation Distance Recommended Installation Distance Recommended Installation Distance Isodrive 900 motor, recommended 4 to 5 metres of flexi ducting. Isodrive 900 motor, recommended 4 to 5 metres of flexi ducting. Isodrive 900 motor, recommended 4 to 5 metres of flexi ducting. -
Page 6: Minimum Mounting Height
Any installation problem must be reported to Schweigen. Call outs relating to incorrect installation will result in a service fee direct to the customer. Schweigen takes no responsibility for problems caused by faulty installation, this may void warranty. A www.schweigen.co.nz or call... -
Page 7: Description
3. Description Isodrive Motor Included in the box: 1. Isodrive 900 motor (280W x 200H mm approx.) Approx. 3 metre, 10amp cable and standard male plug 2. Fire resistant 150mm (160mm OD (160mm OSD) ) PVC riser pipe Note: Cable cut-out at the bottom end only 3. -
Page 8: Installation
4. Installation 900 motor 50mm Pipe protrusion above dektite Power Cord 160mm (OSD) 150mm PVC Pipe (Locking holes fan end) Dektite Fix fan module using side locking screw Fit side supports to locate pipe Strap to supports Bell-mouth Adaptor Connect to NOTE: Prevent any cord bunching by rangehood pulling cord through from plug top end... -
Page 9: Roof Installation
Please be aware that the 900 motor is capable of expelling air at 900m /hr. For more information on environmental noise limit and conditions please contact your local Council. We have a list of recommended installers available on the Schweigen website. Page 9... -
Page 10: Wall Installation
Seal with silicone or urethane Locking screws to be fully *Optional wall mounting flange (P40113MF) is available tightened engaging in holes from Schweigen, please contact 1300 829 066. Figure 2 Wall Installation IMPORANT For more flexible ducting instructions, refer page 22. Page 10... - Page 11 4. Installation IMPORTANT: When mounting pipe fan locking holes to be in outside end of pipe (fan end) Min 150mm long 160mm (OSD) 150mm PVC pipe Locking holes at 10 and 4 o’clock Bell-mouth Adaptor Flexible 200mm ducting Min 50mm 900 motor Cord slots at bottom (6 o’clock position)
-
Page 12: Flat Roof Installation
*Optional wall mounting flange (P40113MF) is available *Optional wall mounting flange (P40113MF) is available from Schweigen, please contact 1300 829 066. from Schweigen, please contact 1300 829 066. 0800 200 510. Figure 4 Figure 4... -
Page 13: Through Wall Installation For Isodrive 900
Minimum pipe protrusion from wall surface Wall 47mm Power cord Wall cover plate Slot in pipe at bottom (6 O’Clock) (optional part) *Optional parts are available from Schweigen, please contact 1300 829 066. 0800 200 510. Figure 5 Page 13... -
Page 14: Fan Unit Shutter Assembly For Isodrive 900 (Optional)
4. Installation Fan Unit Shutter Assembly for Isodrive 900 (Optional) 1. Assemble by fitting shutter assembly into fan inlet shroud moulding, ensuring that attaching screws align with holes. Alignment can be checked visually by folding in shutter flaps. 2. Fully tighten both screws and re-check fitment into holes. -
Page 15: Twin 200Mm Outlet Installation Example
4. Installation Twin 200mm Outlet Installation Example This is for use where one motor is to be used and there are two 200mm outlets, refer figure 11. 900 motor Ensure flexible ducting is fully extended and as short as possible. Use smooth flowing curves for maximum air flow. -
Page 16: Measurements
5. Measurements Measurements for Isodrive 900 (Not to Scale) 278mm 157mm 131mm 198mm 53mm 242mm 440mm Dektite 160mm Shutter assembly (optional) is not shown in the diagram. Page 16... -
Page 17: Flexible Duct
Incorrect installation may reduce airflow or increase noise levels. Call outs relating to incorrect installation will result in a service fee directed to the customer. Schweigen will take no responsibility for problems caused by faulty installation. A list of preferred Schweigen installers can be obtained from the Schweigen website www.schweigen.com.au. -
Page 18: Shallow Roof Space
6. Flexible Duct Shallow Roof Space In shallow roof spaces, do not crush or kink flexible ducting, as it will reduce air flow severely. 90 degree curve made of PVC or galvanise can be used as a substitute for the bend, refer to figure 12. 90 degree curve PVC or galvanise curve Figure 12... -
Page 19: Securing Flexible Duct
6. Flexible Duct Securing Flexible Duct Flexible duct must be installed with supports at maximum intervals of 1.5 metres. Flexible ductwork can be supported by using gaffer or electrical tape. Provided that it does not restrict the internal diameter of the ducting. -
Page 20: Parts List
7. Parts List Parts List for Isodrive 900 Page 20... - Page 21 7. Parts List Parts List for Isodrive 900 Number Part Description Quantity Number P40100 Terminal Block Cover P40121 Wire Insulator Cap P1061 O Ring 4¼” ID P1059 Capacitor 2μF P807 Terminal Block P40102 Fan Plate – Motor Mount P40122 900 Inlet Shroud Mount...
-
Page 22: Maintenance
8. Maintenance Roof Restoration or Cleaning Before doing your roof restoration or cleaning, please completely cover the outside motor system and avoid all chemical contact. IMPORANT Any damages caused by the use of chemical products are not covered by warranty. Figure 15 Avoid chemical contact to motor system Page 22... -
Page 23: Warranty/Disclaimer
All information supplied is to be used for general reference purposes only and is on the understanding that Schweigen Home Appliances will not be liable for any loss, liability or damage of whatever kind arising as a result of any reliance upon such information. All pictures used in the guide are for illustrative purposes only. - Page 24 New Zealand 5 Tolich Place, Henderson, Auckland 0610. Phone 0800 200 510 8/3-4 Anzed Court, Distributed by: Email info.parex@whirlpool.com Web www.schweigen.co.nz Mulgrave 3170 Victoria. 1300 881 693 (EST) www.schweigen.com.au...
Need help?
Do you have a question about the Isodrive 900 and is the answer not in the manual?
Questions and answers